Ekwb EK-FC GV100 PRO Manual de usuario

INSTALLATION MANUAL

EK-FC GV100 PRO BACKPLATE

BACKPLATE

- 2 -

This product is intended for installation only by expert users. Please

consult with a qualiﬁed technician for installation. Improper installation

may result in damage to your equipment. EK Water Blocks assumes no

liability whatsoever, expressed or implied, for the use of these products,

nor their installation. The following instructions are subject to change

without notice. Please visit our web site at www.ekwb.com for updates.

Before installation of this product please read important notice,

disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

Please carefully read the manual thoroughly before beginning

with the installation process!

Please remove your graphics card from the computer to assure

safest mounting process in order to prevent any possible

damages to your GPU and/or graphics card circuit board (PCB).

The EK ﬁttings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured by the

rubber O-ring gaskets.

The use of corrosion inhibiting coolants is always recommended

for any liquid cooling system.

Do not use pure distilled water! For best results EK recommends

the use of EK-CryoFuel coolants!

- 3 -

TABLE OF CONTENT

GENERAL INFORMATION 4

INSTALLING THE BACKPLATE 4

ATTACHING EK-FC GV100 PRO BACKPLATE TO THE GRAPHICS CARD 6

REQUIRED TOOLS 6

IMPORTANT DISCLOSURES 7

SUPPORT AND SERVICE 8

SOCIAL MEDIA 8

- 4 -

INSTALLING THE BACKPLATE

STEP 1

PREPARING YOUR GRAPHICS CARD

EK-FC GV100 PRO Backplate is very easy to install. First install EK-

FC GV100 water block according to its installation manual. If you

have it already installed, please check the picture below to see which

mounting screws are to be left in their position and which are to be

removed. Please remove the four (4) M2.5x4 AX1 screws and their

PVC washers as well (marked with arrow).

STEP 1

GENERAL INFORMATION

STEP 1

Sample picture of Quadro GV100 graphics card.

STEP 1

- 5 -

STEP 2

EK-FC GV100 PRO features passive cooling of the printed circuit

board and its components therefore it is mandatory to install the

enclosed thermal pad. Please install enclosed 1.0mm thermal pad (

Thermal Pad G 1.0mm (120x24)) as shown on the picture below. You

may need to trim the excess thermal pad.

1. Thermal Pad G – 1.0mm (EAN: 3830046996770)

STEP 2

M 2.5 x 4 AX1

3 pcs

M 2.5 helix nut

5 pcs

BAG CONTENT:

Bag content is universal for all backplates, you may not need all screws.

M 2.5 x 6 AX1

7 pcs

M 2.5 x 7 AX1

7 pcs

M 2.5 PVC washer

10 pcs

- 6 -

REQUIRED TOOLS

Phillips-head screwdriver Scissors

STEP 1

Take enclosed mounting screws and install them as shown on

picture below.

HINT: Do not tighten screws until they are all positioned in their

mounting holes. The backplate has milled in standoffs, so there

is no fear of over tightening of the screws. Nevertheless, do not

exaggerate with screwing force as there is no need for it

By all means users must also consider that this product is intended

to be used only with EK-FC GV100 PRO series water blocks. No other

3rd party heat sinks or coolers are ofﬁcially supported! EK does not

offer any assistance or support in the latter application.

STEP 1

ATTACHING EK-FC GV100 PRO BACKPLATE TO THE GRAPHICS CARD

M2.5 Helix nuts

M2.5 X 6 AX1 Screws

M2.5 X 7 AX1

Screws

Plastic

washers

- 7 -

IMPORTANT DISCLOSURES

VERY IMPORTANT NOTICE

Once the installation is completed, it is a recommended practice to

test the cooling circuit for leaks prior to powering up the computer.

We recommend a 24 hour leak test prior to powering up the

computer. Do not test the water block using city water pressure. This

will rupture the top of the housing and render the block unusable

(and will void your warranty).While all efforts have been made to

provide the most comprehensive tutorial possible, EK Water Blocks

assumes no liability expressed or implied for any consequential

damage(s) occurring to your equipment as a result of using EK Water

Blocks cooling products, either due to errors or omissions on our

part in the above instructions, or due to failure or defect in the EK

Water Blocks cooling products.

WARRANTY

Our products are warranted against defects in materials or

workmanship for a period of 24 months beginning from the date of

delivery to the ﬁnal user. During this period, products will be repaired

or have parts replaced at our discretion provided that: (I) the product

is returned to the agent from whom it was purchased; (II) the product

has been purchased by an end user and has not used for commercial

purposes; (III) the product has not been misused, handled carelessly,

or used in a manner other than in accordance with the instructions

provided describing its installation and proper use. This warranty does

not confer rights other than those expressly set out above and does

not cover any claims for consequential loss or damage. This warranty

is offered as an extra beneﬁt and does not affect your statutory rights

as a consumer. This warranty is voided if the product comes in contact

with aggressive UV additives or other improper liquids.

EK blocks are sealed with warranty void circular label, which proves

that the block has withstood a pressure leak test. Removing it will void

leak-free guarantee and not the guarantee on the product itself. Any

other RMA issues can be reported to EK Support at www.ekwb.com/

support for further analysis.

For assistance please contact:

http://support.ekwb.com/

EKWB d.o.o.

Pod lipami 18

1218 Komenda

Slovenia - EU

EKWaterBlocks

@EKWaterBlocks

ekwaterblocks

EKWBofﬁcial

SUPPORT AND SERVICE

SOCIAL MEDIA

Otros manuales para EK-FC GV100 PRO

Tabla de contenidos

Otros manuales de Accesorios de computadora de ekwb

ekwb

ekwb EK-FC7970 Series Manual

ekwb

ekwb EK-Classic DP Side PC-O11D G1 D-RGB + DDC 3.2... Manual de usuario

ekwb

ekwb EK-Quantum Vector D-RGB Upgrade Kit Manual de usuario

ekwb

ekwb EK-FC Radeon Vega Strix Series Manual de usuario

ekwb

ekwb EK-XTOP Revo D5 PWM RGB Series Manual

ekwb

ekwb EK-FB Manual

ekwb

ekwb EK-FB ASUS M8G Monoblock Series Manual de usuario

ekwb

ekwb EK-FC6990 Manual

ekwb

ekwb EK-Supreme HF Series Manual

ekwb

ekwb EK-FB GA Z270X Monoblock Series Manual de usuario

ekwb

ekwb EK-FC970 GTX Series Manual

ekwb

ekwb EK-FC 6970 V2 Guía

ekwb

ekwb EK-FC R9-290X DCII Original CSQ Series Manual

ekwb

ekwb EK-FC Strix RTX 2080 Ti Backplate Classic Manual de usuario

ekwb

ekwb EK-FB ASUS M9H Monoblock Series Manual de usuario

ekwb

ekwb EK-Quantum Surface P360M Manual de usuario

ekwb

ekwb EK-FC R9-285 Series Manual

ekwb

ekwb EK-FB RE3 Manual

ekwb

ekwb EK-Supremacy sTR4 Series Manual de usuario

ekwb

ekwb EK-RAM Monarch Series Manual de usuario

ekwb

ekwb EK-FC R9-290X Matrix Series Manual

ekwb

ekwb EK-FC R9-290X SE Series Manual

ekwb

ekwb EK-VGA Supremacy Series Manual

ekwb

ekwb EK-FB GA X399 GAMING RGB Monoblock Series Manual de usuario

Manuales populares de Accesorios de computadora de otras marcas

Motorola

Motorola ATRIX Manual de usuario

HP USB Media Docking Station Manual de usuario

Cherry

Cherry B.UNLIMITED 3.0 Manual de usuario

Logitech

Logitech IO2 Manual de usuario

ARM

ARM DSTREAM-ST Manual de usuario

Bartec

Bartec TC 7 Series Manual de usuario

Philips

Philips SPC3540 Manual de usuario

Logitech

Logitech mk220 Manual de usuario

SilverStone

SilverStone LC02 Manual de usuario

Flexispot

Flexispot ML2B Manual de usuario

Hamlet

Hamlet UNIVERSAL COVER 101 KBT2 Manual de usuario

Adam Equipment

Adam Equipment RS-485 Manual de usuario

Vivo

Vivo MOUNT-KB05-4DW Manual de usuario

Kvaser

Kvaser Memorator Professional Manual de usuario

DRC

DRC D-Imaging Manual de usuario

Sven

Sven Base 305 сombo Manual de usuario

Hama

Hama 108310 Manual de usuario

SpeechWare

SpeechWare FlexyMike FMK03 Manual de usuario

ekwb EK-FC GV100 PRO Manual de usuario

Manuales populares de Accesorios de computadora de otras marcas