Eiki LC-XBS500 Manual de usuario
Quick Start Guide
MODEL
Use this book as a start guide when setting up the projector.
For detailed information about installation, setup and operation of projector,
refer to the owner's manual on the CD-ROM.
Read the safety instructions in this quick start guide before using projector.
LC-XBS500
LC-WBS500
Quick Start Guide
MODEL
Use this book as a start guide when setting up the projector.
For detailed information about installation, setup and operation of projector,
refer to the owner's manual on the CD-ROM.
Read the safety instructions in this quick start guide before using projector.
LC-XBS500
LC-WBS500
5
Package Overview
Unpack and inspect the box contents to ensure all parts listed below are in
the box. If something is missing, please contact your dealer.
Owner's Manual(CD) AC Power cord Remote Control with batteries
(AA or LR6)
VGA cable Quick Start Guide Lens Protection Ring
6
Install remote control batteries
Operating range
Wired Remote Control Transmitter
①Open the battery cover. ②Install new batteries. ③Put the cover back.
Two AA batteries
For correct polarity
(+ and –), be sure
battery terminals
are in contact
with pins in the
compartment.
Point the remote control toward the remote
control receivers on the projector (front and
back) when pressing any button.
The maximum operating range for the remote
control is about 5 meters and 60 degrees.
The remote control can be used as a wired
remote control. Wired remote control helps you
use the remote control outside of the operation
range (26.25'/8m). Connect the remote control
and the projector with the remote control cable.
Connected with the remote control cable, the
remote control does not emit wireless signal.
To ensure safe operation, please observe the following precautions:
● Use two (2) AA or LR6 type alkaline batteries.
● Always replace batteries in sets.
● Do not use a new battery with a used battery.
● Avoid contact with water or liquid matter.
● Do not expose the remote control to moisture or heat.
● Do not drop the remote control.
● If the battery has leaked in the remote control, carefully wipe the case clean and
install new batteries.
● Risk of explosion if two batteries are replaced by an incorrect type.
● Dispose of used batteries according to the instructions on the battery or local
regulations or guides.
30°
30°
30°
30°
5m
5m
Adjusting
7
Positioning the projector
Note:
● The brightness in a room has a great inuence on image quality. It is recommended to limit the
ambient lighting in order to get the best image.
● All measurements are approximate and may vary from the actual sizes.
Note:
The data in "()" is the project distance for
16:9 aspect ratio.
Note:
The data in "()" is the project distance for
16:9 aspect ratio.
16:9 :
16:9 :
4:3 :
16:10 :
Screen size
(WxH)mm
4:3 aspect ratio
30" 100" 150" 200" 300"
610x457 2032x1524
3048x2286
4064x3048 6096x4572
Maximum 0.882m 3.034m 4.570m 6.107m 9.180m
Minimum 1.482m 5.031m 7.566m 10.101m 15.171m
Screen size
(WxH)mm
16:9 aspect ratio
30" 100" 150" 200" 300"
664x373 2213x1245
3320x1867
4427x2490 6641x3735
Maximum 1.111m 3.796m 5.713m 7.631m 11.466m
Minimum 1.859m 6.288m 9.452m 12.616m 18.943m
Screen size
(WxH)mm
16:10 aspect
ratio
30" 100" 150" 200" 300"
646x404 2154x1346
3231x2019
4308x2692 6462x4039
Maximum 0.938m 3.219m 4.848m 6.477m 9.735m
Minimum 1.573m 5.336m 8.023m 10.711m 16.086m
Adjustable feet
The projection angle can be adjusted up to 40
mm with the adjustable feet.
Rotate the adjustable feet to lift the projector
to a certain height. During lifting, rotate the two
feet clockwise.
To lower or retract the adjustable feet, rotate
the two feet counterclockwise.
Keystone distortion of projected images can
be corrected by auto settings, remote control
operation or menu operation. Adjustable feet
Screen size
(WxH)mm
16:9 aspect ratio
30" 100" 150" 200" 300"
664x373 2213x1245
3320x1867
4427x2490 6641x3735
Maximum 1.111m 3.796m 5.713m 7.631m 11.466m
Minimum 1.859m 6.288m 9.452m 12.616m 18.943m
LC-WBS500:
LC-XBS500:
30”
30”
(Diagonal:Inch)
Max. Min.
(Center)
(Diagonal:Inch)
Max. Min.
(Center)
0.882m(1.111m)
3.034m(3.796m)
4.570m(5.713m)
6.107m(7.631m)
9.180m(11.466m)
15.171m(18.943m)
0.938 m(1.111m)
3.219m(3.796m)
4.848m(5.713m)
6.477 m(7.631m)
9.735 m(11.466m)
16.086m(18.943m)
30”
30”
(Diagonal:Inch)
Max. Min.
(Center)
(Diagonal:Inch)
Max. Min.
(Center)
0.882m(1.111m)
3.034m(3.796m)
4.570m(5.713m)
6.107m(7.631m)
9.180m(11.466m)
15.171m(18.943m)
0.938 m(1.111m)
3.219m(3.796m)
4.848m(5.713m)
6.477 m(7.631m)
9.735 m(11.466m)
16.086m(18.943m)
Adjusting
8
a
b
Adjusting
Lens shift adjustment
Projection lens can be moved from side to side and up to down.
This function makes the positioning of images easy on the screen.
The display position can be shifted upward up
to 40%(XGA), 50%(WXGA) elevation of the
display.
The display position can be shifted to the left
up to 10% width of the display.
The display position can be shifted to the right
up to 10% width of the display.
When the lens is shifted to top.
When the lens is shifted to leftmost. When the lens is shifted to rightmost.
When the lens is shifted to bottom.
The display position can be shifted downward
up to 40%(XGA), 50%(WXGA) elevation of the
display.
When the lens is
shifted to the center. Shifting range
a: 40% (LC-XBS500)
50% (LC-WBS500)
b: 10% (LC-XBS500)
10% (LC-WBS500)
9
Adjusting
Connecting the AC power cord
This projector uses nominal input voltages of
100–240V AC and it automatically applies to
different input voltages. It is designed to work
with a single-phase power system having a
grounded neutral conductor.
To reduce the risk of electrical shock, do not
plug into any other type of power system. If
you are not sure of the type of power being
supplied, consult your authorized dealer or
service station. Connect the projector with all
peripheral equipment before turning it on.
The AC outlet should be near this equipment
and must be easily accessible.
Note:
Note:
For safety, unplug the AC power cord when the projector is not in use. When the projector is
connected to an outlet with AC power cord, it is in stand-by mode and consumes a little electric
power.
Connect the AC power cord
(supplied) to the projector.
Turn on the projector
1.Complete peripheral connections (with a
computer, HDR,etc.) before turning on the
projector.
2. Connect the projector’s AC power cord into
AC outlet.The POWER indicator turns red.
3. Press the POWER button on side control or
on the remote control. The POWER indicator
becomes green and the cooling fans start to
work. The preparation display appears on
the screen and the countdown starts.
4. If the projector is locked with a PIN code, a
PIN code input dialog box appears. Enter
the PIN code as instructed below.
Note:
● When the logo select is set to be "Off" the
logo will not be displayed on the screen.
● When the Display function is set to be "Off" ,
the logo and countdown will not be displayed
on the screen.
● During the countdown period, all operations
are invalid except shutdown.
16
Start-up display
10
Connecting
Connecting to computer(Digital and analog RGB)
Unplug the power cords of both the projector and external equipment from the AC outlet
before connecting the cables.
Cables used for connection:
● VGA cable ● Serial cable*
● HDMI cable*
(*=Cables are not supplied with the projector)
VGA IN 1 / YCbCr / S-VIDEO IN
RS-232C
VGA IN 2 / VGA OUT
HDMI
LAN
AUDIO IN
(MONO)
VIDEO IN
R L
USB-B USB-A
AUDIO OUT AUDIO INR/C
HDMI output
HDMI
cable
HDMI input
RS232 input
RS232 output
Serial
cable
(Cross)
VGA output VGA input/output
VGA
cable VGA
cable
VGA input VGA output/input
Otros manuales para LC-XBS500
3
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Proyector de Eiki
Eiki
Eiki LC-XB250W Manual de usuario
Eiki
Eiki LC-XB40 Manual de usuario
Eiki
Eiki LC-WIP3000 Manual de usuario
Eiki
Eiki LC-XM4 Manual de usuario
Eiki
Eiki EIP-3500 Manual de usuario
Eiki
Eiki LC-NB1U Guía de configuración
Eiki
Eiki LC-XAU200 Manual de usuario
Eiki
Eiki LC-WNB3000N Manual de usuario
Eiki
Eiki EIP-WSS3100 Manual de usuario
Eiki
Eiki DLP Projector EIP-5000 Manual de usuario
Eiki
Eiki XG-705A Manual de usuario
Eiki
Eiki LC-NB1UW Manual de usuario
Eiki
Eiki HDT700 Manual de usuario
Eiki
Eiki LC-HDT700 Manual de usuario
Eiki
Eiki LC-XIP2000 Manual de usuario
Eiki
Eiki Brilliant LC-XNP4000 Manual de usuario
Eiki
Eiki LC-WB42N Manual de usuario
Eiki
Eiki XL Series Manual de usuario
Eiki
Eiki Powerhouse LC-SX1U Guía de configuración
Eiki
Eiki Xenon ARC EX-1500 Manual de usuario
