Ei Electronics Ei146 Optical Manual de usuario

Shannon Free Zone, Shannon, Co. Clare, Ireland.

Ph.+353 61 471277 Fx.+353 61 471053

Web: www.eielectronics.com

E & OE As our policy is one of continuous product development, we reserve the right to alter product details without prior notice. Ei146 DataSht RevB

Model Ei146 Optical

Easi-Fit base

9V Alkaline Battery back up

High performance optical chamber with integral

insect screen

Test/Hush button

Advanced suppression and calibration technology

Interconnectable to other Ei mains powered alarms

Built in auto self test feature

Low power cell warning

Kitemarked to BS EN 14604:2005

5 year guarantee

Product Description

The Ei146 is an Optical Smoke Alarm that runs on 230V

AC mains power, and has a 9V alkaline battery back up

in the event of mains failure. The 9V battery will last for

up to 4 years in standby mode, and capable of powering

the smoke detector for up to 2 years in the event of

mains failure.

The Ei146 is supplied with the Easi-Fit base that allows

very quick and simple installation of the smoke alarm,

combined with simple detector head removal and

replacement. The Easi-Fit base automatically connects

both mains power and battery as the detector head

slides on to the Easi-Fit base.

The Ei146 has other advanced features such as high

performance optical chambers fitted with integral insect

screens to reduce the chances of false alarms, as well

as the ability to interconnect up to twelve alarms to allow

all alarms to sound if just one of the interconnected

alarms should be triggered.

The Ei146 has built in circuitry to aid suppression of

voltage transients and RF interference to further reduce

the chances of false alarms under such conditions.

Operation

The green indicator will illuminate to show mains

power is present

The red indicator will flash every 40 seconds to

show that the detector has performed an automatic

self test

The red indicator will flash rapidly to show an alarm

condition for the smoke detector

The “Test/Hush” button will either silence false

alarms or perform a unit self test

In “Test” mode the alarm will perform a self test and

sound the horn

In “Hush” mode the alarm enters a ten minute period

of reduced sensitivity to overcome false alarm

conditions, and will then automatically reset itself

When interconnected to other Ei mains powered

alarms, an alarm on one detector will trigger all other

interconnected alarms within one second (only the

triggered alarm will flash a red indicator)

The smoke detector will emit a beep and flash the

red light every 40 seconds to indicate that the

battery back up is depleted and needs replacing

MAINS POWERED 230V~

9V Alkaline Battery Back-Up

Shannon Free Zone, Shannon, Co. Clare, Ireland.

Ph.+353 61 471277 Fx.+353 61 471053

Email. [email protected]

Web: www.eielectronics.com

E & OE As our policy is one of continuous product development, we reserve the right to alter product details without prior notice. Ei146 DataSht RevB

Model Ei146 Optical

Installation & Placement

Wiring for Interconnected Alarms

Be very careful about correctly wiring the alarms as mixing Live and Neutral

will blow/damage interconnected alarms.

Alarms should be placed in accordance with the general guidelines shown in

the diagram above. These recommendations are based on the problem of

areas of “dead air” close to corners of rooms and apexes of ceilings, which

could result in the prevention of smoke reaching the smoke detector

Please consult instruction booklet for specific installation details

Important Precaution:

Do not install the actual smoke/heat alarm

itself in new or renovated buildings until all

work is completed (including floor coverings)

and the building has been fully cleaned. The

wiring can be installed when appropriate.

(Excessive dust and debris from building work

can contaminate the smoke chamber and

cause problems, and it will also invalidate the

guarantee). If it must be installed, cover it

completely, particularly around the edges, with

a dust cover (eg. a plastic bag), until all

cleaning is finished.. Connect wires to the unit

as in wiring diagram. All wiring must comply

with local codes.

Technical Specification

Sensor Optical, uses light scatter from

smoke

Sensitivity: Complies with BS 5446 Part 1:

2000

Source: Contains no radioactive material

Airspeed: Essentially immune to the effect

of airspeed.

Button Test: Simulates the effect of smoke and

checks chamber, electronics and

horn.

Ambient Light: Chamber housing design and

compensation overcomes

problems with stray light.

AutomaticSelf-Test: Smoke Chamber is tested every 40

Sec. and unit beeps (without LED

flash) if it is degraded.

Insect Screen: Prevents insects or debris entering

chamber (1.00mm mesh size)

Supply Voltage: 230V AC

Battery back up: 9V Alkaline Battery

Specifications are subject to change

Power-On Indicator: Continuous green LED

Alarm: Electronic Piezoelectric horn

Alarm Sound Output: 85dB (minimum) at 3m

Alarm Status: Red LED flashes every second on

unit sensing fire

Temperature Range: 0° to 40°C

Humidity Range: 15% to 95% Relative Humidity

Interconnect: Up to 12 interconnected mains

powered easi-fit smoke or heat

alarms, along with an EI128 relay

base

Fixing: Easi-Fit mounting base

Plastic material: UL94VO flame retardant

Dimensions: 152mm x 50mm depth

Weight: 345g

Warranty: 5 year (limited) warranty

Approvals: Kitemarked to BS EN 14604:2005,

CE Approved

Otros manuales para Ei146 Optical

Tabla de contenidos

Otros manuales de Detector de humo de Ei Electronics

Ei Electronics

Ei Electronics Easichange Series Manual de usuario

Ei Electronics

Ei Electronics Ei141 Ionisation Manual de usuario

Ei Electronics

Ei Electronics Ei 3105TY Manual de usuario

Ei Electronics

Ei Electronics Ei2110e Series Manual de usuario

Ei Electronics

Ei Electronics Ei 181 Ionisation Manual de usuario

Ei Electronics

Ei Electronics Ei 105R Optical Manual de usuario

Ei Electronics

Ei Electronics RadioLINK Ei170RF Manual de usuario

Ei Electronics

Ei Electronics Ei141EK Manual de usuario

Ei Electronics

Ei Electronics Ei156TLH Optical Manual de usuario

Ei Electronics

Ei Electronics EiA207 Series Manual de usuario

Ei Electronics

Ei Electronics EiA600 Series Manual de usuario

Ei Electronics

Ei Electronics Ei605 Series Manual de usuario

Ei Electronics

Ei Electronics Ei605MTYRF Manual de usuario

Ei Electronics

Ei Electronics Ei 100TYC Ionisation Manual de usuario

Ei Electronics

Ei Electronics aico Ei146e Manual de usuario

Ei Electronics

Ei Electronics Ei144 Heat Manual de usuario

Ei Electronics

Ei Electronics EI129 Manual de usuario

Ei Electronics

Ei Electronics Ei161RC Ionisation Manual de usuario

Ei Electronics

Ei Electronics Ei 151TLR Ionisation Manual de usuario

Ei Electronics

Ei Electronics Ei650iW Manual de usuario

Ei Electronics

Ei Electronics Ei141 Ionisation Manual de usuario

Ei Electronics

Ei Electronics Ei161e Manual de usuario

Ei Electronics

Ei Electronics Ei3105RF Optical Manual de usuario

Ei Electronics

Ei Electronics Heat Alarm Ei 164R Heat Manual de usuario

Manuales populares de Detector de humo de otras marcas

x-sense

x-sense SD19-W Manual de usuario

BRK electronic

BRK electronic First Alert P1010 Manual de usuario

FireAngel

FireAngel Thermoptek ST-622 Manual de usuario

teko

teko Astra-42A Manual de usuario

Safetec

Safetec SDS-2/6 Manual del propietario

Siemens

Siemens PE-11C Manual de usuario

System Sensor

System Sensor DH500ACDC Manual de usuario

Resolution Products

Resolution Products RE612 CryptiX Manual de usuario

First Alert

First Alert PC900V Manual de usuario

Eminent

Eminent EM6590 E-Domotica Manual de usuario

Carrier

Carrier Kidde Quell Q301 Manual de usuario

VESDA

VESDA VLF-500 Manual de usuario

ELRO

ELRO FS8110 Manual de usuario

Heiman

Heiman SMOKI NS-626PHS Manual de usuario

Regin

Regin SDD-S65 Manual de usuario

Family Gard

Family Gard FG225 Manual de usuario

Greystone

Greystone DSD120 Manual de usuario

Aparton

Aparton ASD-10 Manual de usuario