EFT Z Series Guía de instalación

Z SERIES AGRICULTURAL DRONE SYSTEM

（Model：Z30/Z 50）

A s sembly Instruction Manual

Version 1.0 EN202 3

Co ntents

Safety Guidelines ................................................................................................................................................................. 1

In The B ox ............................................................................................................................................................................. 2

Preparations ......................................................................................................................................................................... 3

Installation Steps ................................................................................................................................................................. 4

Parts I ntroduction ....................................................................................................................................................... 4

Flow C hart .................................................................................................................................................................... 4

Steps ............................................................................................................................................................................. 5

Step 1：Install la nding gear ...............................................................................................................................5

Step 2：Install motor set and drone arms ....................................................................................................... 6

Step 3：Connect Cables .................................................................................................................................... 8

Step 4：Install T he Centrifugal Nozzles ......................................................................................................... 10

Step 5：Install C amera .....................................................................................................................................10

Ending : .............................................................................................................................................................. 11

Switch Spreading Tank ............................................................................................................................................. 11

Specifications ..................................................................................................................................................................... 12

Z Series Assembly Manual

Safety Guidelines

1. Please carefully check the goods according to the product list before assembly, complete the installation according

to tutorial video or this manual.

2. Make s ure that you have well known the each part of this product before assembling this product. Do not assemble

it violently. If you have any questions when assembling this product, please contact EFT or the authorized agency.

3. Not being a toy, plus for certain safety risks, the product is not suitable for t hose who are under 18 years old, or

those who have no or limited capacity for civil conduct, or those with mobility impairments, or those restricted by

existing laws ， regulations and policies. Please keep the product out of reach of children and be particularly cautious

while there are children present.

4. Before installing this product, please make sure that you have fully understood the features and functions of the Z

series products, have professional installation and debugging techniques, and strictly follow this manual to install the

various parts of the drone. Incorrect as s embly may cause personal injury or the device is not running properly.

5. During assembly, please check each component carefully to see that it is properly connected and all in the correct

position.

6. During t he installation, please operate carefully to avoid damage and loss caused by improper operation.

7. When installing t he water pipe, do not bend it much to avoid creases and affect the s praying effect.

8. For replacement parts, please purchase original repair parts.The components from other sources may cause failure

and users shall take the risk.

9. Unauthorized disassembly, modification, installation or use of this product for purposes other than t he original

design is prohibited, otherwise the warranty will be invalidated.

10. Be sure to connect and insert t he battery and turn on the power after completing all the installation and wiring.

11. Please complete all assembly and no-load flight test , spraying inspection, and then carry out field operations.

12. Before test , please confirm whether the remote control can be connected normally and whether the battery

power is suff icient. During testing, make sure the drone is in an open area to avoid hitting obstacles or people.

Warning

Improper assembly will affect product performance, please ensure that you have professional installation and

debugging techniques, and strictly follow with this manual. We do not accept any return or exchange due to subjective

factors, such as subjectively determined that it is not easy to use, don't know how to use, and the performance does

not meet the expected, which are non-product quality problems. All damages and risks from personal reasons during

assembly and operation shall be borne by t he users, we do not assume any related liability.

Z Series Assembly Manual

In The Box

When unpacking, please check that all items in this checklist are included according to the package you purchased. If

there is something missing, please contact our after-sales customer s er vice team in t ime.

Product Form：CKD

Number of packages：2

Packaging Materials：Carton + protective foam

The packaging reference is as follows:

Three soluti ons are optional, as follows ：

Item

Basi c s et

Advanced set

Standard s et

Drone frame

√

Motor set*4

√

Impeller pump*2

√

Flowmeter

√

Liquid level gauge

√

Centrifugal nozzle*2

√

Switchboard

√

Piping fittings

√

Flight control

√

Receiver

√

Camera

√

Remote control

√

RTK

√

Rear radar

√

Front radar

√

Altitude Radar

√

* Warm tips：

Due to long distance in ternational shipments, the product protruding parts may be cracked by pressure, vibration and v iole n t transportation,

especially at the interface of the flowmeter, which may cause water leakage. We strongly recommend that you carefully check each part for

deformation, cracks or other damage a f ter receiving the goods. If the re is any problem, please contact us and apply for replacement.

Box 1：①drone body ②landing gear ③

motor set ④paddle ⑤paddle clip ⑥fittings

Box 2：①Tanks and S prinklers ②

Remoto control ③Centrifugal nozzles

Z Series Assembly Manual

Preparations

Required t ools

1. Screwdriver Set: For tightening and loosening screws.

2. Extended screwdriver (M4, M5 models): For tightening and loosening screws.

3. Screw g lue (provided): For locking s crews, bolts and nuts.

4. Grease (provided): For sealling the plug.

5. Scissors/utility knife: For cutting wires, tape, etc.

6. Level: Used to level the motor s et.

7. Hexagonal socket 6mm: For t ightening and loosening the hexagonal stud at t he locking buckle of the arms.

8. Ordinary safety g loves.

In spection

• Check the model, specification, the number of boxes, accessories, and the compatibility of each parts according to

the list of items. If there are something wrong or miss ing, please take photos as evidence.

• Check whether the components are in good condition, whether the tripod is deformed, whether the internal flight

control is loose, whether the plug connector is s kewed or falling of f, whether there is any crack at the f low meter

connector, etc. If t here are any of the above situations, please contact customer serv ice as soon as poss ible.

Mount ing fittings

Item

Spec.

Qty

Application

Tee Fixing

landing gear bar

Sticker

Arm locking handle and Motor base

Grease

The plug of the signal cable

Screw fastening glue

Arm mounting

Camera bracket

Camera installation

M4*35 Cylindrical screw+M4 nut

M3*8 Cylindrical screw

Φ8*23 Long pin*4

Locking handle installation

φ8*17 Short pin

M4*75+6 Hex stud

M4*12 Cylindrical screw

Gasket

Arm installation

M6*12Locking screw

φ8*M6*78Locking nut

M4*10

Cylindrical screw

Landing gear fixtures

M4*20

Cylindrical screw

M4*30

Cylindrical screw

landing gear bar

M3*16 Cylindrical screw

Nozzle installation

Z Series Assembly Manual

Installation Steps

Parts I ntroduction

Flow C har t

Motor set *4

Paddle*4

Drone ar m*4

landing gear mount*4

landing gear bar

Landing gear *2

Drone bo dy

Centrifugal n ozzle * 2

Tanks an d Sprinklers

Remote control bag

Fitting bag

Z Series Assembly Manual

Steps

Step 1：Install landing gear

1. Open the package, take out the drone frames , the landing gear and crossbar components as well as the mountings and screws.

2. Remove the front and rear upper and lower covers to facilitate the turn over the frame and subsequent assembly.

3. Insert the m ounts into both ends of the bent l egs.

4. Turn t he frame over, then install the bent legs on the frame, note the arrow to head. Use M4*20 screws to fasten, and then use

M4*12 screws to fix t he mounting seat .Do not fasten to facilitate the frame leveling.

5. After installing the landing gear on both sides, install the four tee fixings according to the positioning marks on the bent legs, and

pay attention to the interface horizontally inward.

Z Series Assembly Manual

6. Insert the front crossbar F (351mm) and the rear crossbar B (322mm) into the tee fittings, and fasten them with M4*30 half-thread

screws.

7. Restore the receiver antenna, remove the tape, and fix the antenna with M4*10 cylindrical screws.

8. After the landing gear is installed, press the frame to level the drone, and then tighten t he m ounting seat of the landing gear.

Step 2：Install motor set and drone arms

Tips

*Pay attention to each arm label and motor code, clockwi s e from the head is M1-M4 in turn , in stall CCW at M1 and M3 , and install CW at M2

and M4.

*The M1 an d M 2 arms with the motor cable, But the M3 and M4 a rm s will through the water pipe and the nozzle adapter cable first, and then

threaded into the motor cables, and then lightly lock them to a void falling off.

*It is recommended to install the propeller wh en test the ai rcraft. Note that the CCW an d CW motor are respectively a dapted to the

corresponding paddles.

1. Take one of CW and one of CCW, and pass the nozzle adapter cable and water pipe through the motor head, and the other two

motors no need.

2. Insert the 4 motor sets and cables into the carbon tube arm, and fix them with the screws on the motor base, do not tighten them

for adjusting later.

Z Series Assembly Manual

3. Install the spacer on the arm head swivel position .

4. Remove the wire buckle and the cable-passing seal.

5. Put the arm with the n ozzle adapter cable, the water pipe into the rear frame folder, and the arm without the water pipe into the

front frame folder, then use the φ8*M6*78 lock nut to penetrate from t he upper part. The l ower M6*12 pair lock screws need to be

glued

(the glue has been supplied as standard) ( the cable faces forward and the water pipe faces backward).

6. Install the l ocking buckle of the arm, insert the long pin into the hole of the arm holder, in sert the short pin into the hole of the

handle, and then insert the hexagonal stud into the long pin at the end of the arm.

Z Series Assembly Manual

7. Adjust the arm handle to a suitable angle, use M4*12 screws to pass through the short pin of t he handle, insert into the hexagonal

stud and t ighten.

8. Affix 'Watch Your Fingers' on t he buckle of the arm and 'Mind The Blade' on the motor fixing place.

9. Follow the above steps to install the remaining arms and m otors.

Step 3：Connect Cables

1. Pass each cable of the motors through the cable-passing seal , and then restore the seal.

2. Assemble the wire buckle to the frame, adjust the l ength of t he cables to facilitate the insertion.

Short Pin

Long Pin

Hexagonal stud

Otros manuales para Z Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Zumbido de EFT

EFT

EFT G20 Manual de usuario

EFT

EFT Z Series Manual de usuario

EFT

EFT G06 Manual de usuario

EFT

EFT E416P Manual de usuario

Manuales populares de Zumbido de otras marcas

Ryze

Ryze Tello Manual de usuario

PowerVision

PowerVision PowerRay Manual de usuario

Force1

Force1 rogue F72 Manual de usuario

Zerotech

Zerotech DOBBY Manual de usuario

Protocol

Protocol VIDEODRONE AP Manual de usuario

dji

dji Matrice M210 Manual de usuario

MAKE

MAKE Terry Kilby Manual de usuario

SYMA

SYMA X440 Manual de usuario

RUKO

RUKO F11 Manual de usuario

SYMA

SYMA X5UW(720P) Manual de usuario

Dynali

Dynali 25 H Guía

dji

dji PHANTOM 4 Manual de usuario

Atlas

Atlas AtlasPRO Manual de usuario

Twodots

Twodots TVVIN BOARD Manual de usuario

GDU

GDU SAGA Manual de usuario

Ares

Ares ETHOS QX 130 Manual de usuario

Walkera

Walkera ZHUN Manual de usuario

dji

dji WIND-4 Manual de usuario