Edwards 10 Manual de usuario

C410-01-882

Issue B Original

Instruction Manual

Model 10 Water Jet Pump

This page has been intentionally left blank.

Edwards and the Edwards logo are trademarks of Edwards Limited.

Contents

C410-01-882 Issue B

Contents

Section Page

1 Technical Data ....................................................................................1

2 Construction .......................................................................................2

3 Installation notes .................................................................................3

For return of equipment, complete the HS Forms at the end of this manual.

Illustrations

Figure Page

1 Model 10 Water Jet Pump .............................................................................................. 3

Associated publications

Publication title Publication number

Vacuum pump and vacuum system safety P400-40-100

edwards jp 08/09

C410-01-882 Issue B

Edwards and the Edwards logo are trademarks of Edwards Limited.

Contents

Edwards and the Edwards logo are trademarks of Edwards Limited.

Technical Data

C410-01-882 Issue B

1TechnicalData

Note: *Performance is limited only by the temperature and pressure of the water supply. At a water pressure of

1.4 bar (20 lbf in-2) and a temperature of 15 ºC, the pumping speed is approximately 3.9 l min-1, and the

ultimate vacuum 17 mbar. Water consumption is approximately 625 l h-1.

The Model 10 pump operates from standard water supplies to produce rough vacuum for application in the

distillation, filtration aeration fields and general duties not requiring higher performance mechanical vacuum pumps.

Model 10

Operating water pressure (optimum) 1.4 bar (20 lbf in -2)

Operating water temperature 15 ºC

Operating water pressure (recommended) 1 to 2 bar (15 to 30 lbf in -2)

* Pumping speed (air) 3.9 l min-1

Ultimate vacuum 16 to 18 mbar

Water consumption 625 l h-1

Connections

Water in 12 mm bore tubing

Drain 3/8 in (9.5 mm) bore tubing

Vacuum 7 mm bore tubing

Weight 34 g

Product Description Order number

Model 10 water jet pump C410-01-000

Spares Order number

Viton ball/pin assembly for non-return valve C039-01-010

C410-01-882 Issue B

Edwards and the Edwards logo are trademarks of Edwards Limited.

Construction

2Construction

The pump is constructed from a plastic material (PPS) which has high corrosion resistance properties. The material

is non-flammable and is resistant to a wide range of solvents, mineral and organic acids and alkalis. It must NOT be

used with the following:

Bromine (wet)

Butyl Amine

Chlorosulfonic Acid

Chlorine (dry)

Chromic Acid Conc

Hydrogen peroxide 30%

Morpholine

Nitric Acid 35% to Conc

Sulphuric Acid 98%

Trichlorethylene

Riffled nozzles are provided on the pump for the water and vacuum connections and an internal non-return valve

prevents flooding of the vacuum system in the event of fluctuating water pressure.

C410-01-882 Issue B

Edwards and the Edwards logo are trademarks of Edwards Limited.

This page has been intentionally left blank.

3 Installation notes

1. Connection to the water supply should be made using 12 mm bore tubing and to the vacuum system using 7 mm

bore vacuum tubing. If it is desired to fit a water drain, thus should be of 9.5 mm bore tubing.

Note: After considerable service, the tubing may stick to the nozzles and it should be removed by cutting.

2. Should the jet nozzle assembly or the vacuum connection be removed:

Ensure ball valve is located correctly in the vacuum arm, on re-assembly, so that the pin projects towards

the centre line of the jet nozzle assembly.

The vacuum nozzle should be carefully tightened to a torque setting not exceeding 18 lbf in (maximum) and

the jet nozzle to a torque setting not exceeding 24 lbf in (maximum).

CAUTION

The ball valve is manufactured from an elastomer which is liable to swell in the presence of certain chemical

(particularly ketones and esters). Should the pump cease to operate when such chemicals are present, then the

valve is suspect and should be inspected. Access to the valve is obtained by unscrewing the vacuum nozzle.

Renew the valve ball if swollen or deteriorated.

Figure 1 - Model 10 Water Jet Pump

1. Water inlet

2. Jet nozzle assembly (C410-01-001)

3. Ball/Pin assembly (C039-01-010)

4. Vacuum connection (C410-01-004)

5. Vacuum

6. Body (C410-01-005)

7. Water drain

C410-01-882 Issue B

Edwards and the Edwards logo are trademarks of Edwards Limited.

This page has been intentionally left blank.

Tabla de contenidos

Otros manuales de Bomba de agua de Edwards

Edwards

Edwards nRVi Manual de usuario

Edwards

Edwards RV3 Manual de usuario

Edwards

Edwards nXDS6i Manual de usuario

Edwards

Edwards xds35i Manual de usuario

Edwards

Edwards EXTPX Series Manual de usuario

Edwards

Edwards A726-01-805 Manual de usuario

Edwards

Edwards EXT70/70200 Manual de usuario

Edwards

Edwards EH500T4 T3 Series Manual de usuario

Edwards

Edwards GXS Series Manual de usuario

Edwards

Edwards STP Series Manual de usuario

Edwards

Edwards A730-01-983 Manual de usuario

Edwards

Edwards STP Series Manual de usuario

Edwards

Edwards STP Series Manual de usuario

Edwards

Edwards nEXT240 Manual de usuario

Edwards

Edwards STP Series Manual de usuario

Edwards

Edwards STP Series Manual de usuario

Edwards

Edwards XDS Series Manual de usuario

Edwards

Edwards RV3 Manual de usuario

Edwards

Edwards 30B5M Manual de usuario

Edwards

Edwards T-Station 300 Manual de usuario

Edwards

Edwards CDX1000 Manual de usuario

Edwards

Edwards Diffstak 63/150 Manual de usuario

Edwards

Edwards EXT555H Manual de usuario

Edwards

Edwards EXT70 Series Manual de usuario

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario