Edwards AIM Manual de usuario

D145-45-840

Issue C Original

Instructions

Active Inverted Magnetron Gauge - Electrode Kit

These instructions are applicable to the following: AIM Electrode Kit (Item Number D145-45-802), AIM-SL Electrode Kit (Item Number

D145-48-802).

1DismantletheAIMGauge

1. Hold the body tube and magnet housing in separate hands.

2. Push the components together and turn the magnet housing anti-clockwise (relative to the body tube) to release the bayonet-type

locking mechanism, then separate the two components keeping their centre lines in-line.

2Dismantlethetube

1. Unscrew and remove the white collar: take care not to bend the protruding anode assembly pin.

2. Remove the anode: keep the centre line of the tube and anode in-line. Ensure that you do not bend the anode pin.

3. Remove the Viton™ 'O' ring.

4. Use circlip pliers to remove the circlip from the other end of the tube.

5. Remove the cathode from the tube.

3 Reassembly

Reassemble the components as described in Section 2 but in the reverse order. Note that:

zA cathode plate is at one end of the cathode tube. This plate should be at the collar end (that is, the opposite end to the

vacuum flange). When you reassemble the AIM Gauge, make sure that the long pin end of the anode enters the centre hole in

the cathode plate.

zBefore you screw in the collar, check that the anode pin is central within the line of view through the central hole in the

cathode tube.

zWhen you fit the new anode assembly, you must check the gaps between the striker plates and the shield and ensure that they

are correctly set as shown in Figure 1 below.

Figure 1 - Striker plate/shield gap settings

Viton™ is a trademark of DuPont Dow Elastomers L.L.C.

1. Striker plate

2. Shield

3. Striker plate (not fitted

on all anode assemblies)

Ipsitech 9000(K)-2008

D145-45-840 Issue C

Edwards and the Edwards logo are trademarks of Edwards Limited.

This page has been intentionally left blank.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Edwards

Edwards

Edwards AIM-S-NW25 Manual de usuario

Edwards

Edwards AIM-S-NW25 Manual de usuario

Edwards

Edwards APGX-H Manual de usuario

Edwards

Edwards Barocel 7045 Manual de usuario

Edwards

Edwards AIM-S-NW25 Manual de usuario

Edwards

Edwards APG100 Manual de usuario

Edwards

Edwards IG40 BA Manual de usuario

Edwards

Edwards PRG20K Manual de usuario

Edwards

Edwards AIM-S-NW25 Manual de usuario

Edwards

Edwards GXS 0-60 SLM Manual de usuario

Edwards

Edwards TruWave Manual de usuario

Edwards

Edwards OLM100 Manual de usuario

Edwards

Edwards AIM-SI1-NW25 Manual de usuario

Edwards

Edwards FSRZI-A Instrucciones de montaje

Edwards

Edwards ATC-E Manual de usuario

Edwards

Edwards M528-09-160 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario