Edsyn LONER 951SX-230 Manual de usuario

951SX-230

LONER®

Temperature Controlled

Soldering Station

• COMPLIES WITH MIL-S-45743E, MIL-STD-2000-1B, WS6536E AND

ESD SPEC, DOD-STD-1686, DOD-HDBK-263

made

U S A

Instruction manual

Specications for Model 951SX-230

Power Requirements 230V, 50/60 Hz

Power Rating 15W - 220W

Heater Rating 230V, 95W

Temperature Range 400°F-800°F/205°C-427°C

Temperature Regulation ±6°F/±3°C

Tip-to-Ground Voltage

Leakage/Resistance < 2mV/< 2 ohms

Overall Dimension 4.1"W x 8.2"H x 10"D

104 mm x 208 mm x 254 mm

Weight 2.5 lbs/1.1 kg

Contents

951SX-230 includes 1 - LT375 Soldering Tip

PD528 Tool Pod

SH230 Sponge Holder

(Includes RS199 Cleaning Sponge,

RS243 Leveling Pad, LN230 Liner)

WP556 WIGAPRY Low Static Computer Aid

DISTINGUISHING FEATURES

For 951SX-230 For 951SX-230P

POWER CORD WIRING

BROWN to LINE

BLUE to NEUTRAL

GRN/YEL to GROUND

For 951SX-230B

13A Fuse inside

For 951SX-230I

Power Cord

WARNING:

DO NOT HIT OR TAP THE SOLDERING TOOL. THE HEATER ELEMENT WILL BREAK!!!

CAUTION:

Over-lling can cause thermal shock

to the tip or heating element during

tip cleaning.

• Replace RS199 Cleaning Sponge

1. Fill water only up to the top of the RS243

Leveling Pad.

2. Depress RS199 to moisten it completely.

• Replace SC581 Solder Collector

1. Hold the Housing rm and turn Cap

counter-clockwise and pull it away from the

Housing.

2. Remove used SC581 and replace with

a new one.

3. Reassemble Pod with TOP of the Cap in

proper position.

MAINTENANCE

Static Safe

Temp.

Regulation

Indicator

SH230

Sponge Holder

PD528 Tool

Pod

Power Switch

Calibration Pots for HI & LO Temp. Hollow Threadless Heater

LN230

SH230-1

RS243

RS199

SC581

Solder Col-

lector

SR043

Front Hous-

ing

SR042

Thermal

Housing

TEMPERATURE CALIBRATION

1. Turn on power and set Temperature Control Knob to 400°F (205°C).

2. Using a clean and well tinned Tip, apply a small amount of solder on the Tip, just enough

to form a bead on top of the Tip.

3. Place the center of the thermocouple wire of the SDS100 on top of the bead.

4. Again, apply a small amount of solder on the center of the thermo-couple wire, just enough

to embed the center.

5. Adjust LO-Temp. Calibration Pot so the Meter will read 400°F (205°C).

6. Set Temperature Control Knob to 800°F (427°C).

7. Adjust Hi-Temp. Calibration Pot so the Meter will read 800°F (427°C).

TIP CARE

1. Set desired temperature. Blinking Neon Lamp means Tool is ready.

2. TIN the Tip. (apply solder)

3. Do not rub, bend or reshape the Tip.

4. Always clean the Tip by wiping it against the saturated sponge and always RE-TIN.

TIP CLEANING

To maintain proper Tip to Ground resistance.

1. Remove Tip from Heater Assembly.

2. Using a ST707 Soldering Tool Maintenance Brush, clean Tip and Heater Barrel

at surfaces shown.

3. Install the tip and tighten RS372 Retaining Sleeve. Take note of the gap to ensure

proper tting.

MS412

TemperatureCalibration System

SDS100

METER

FX635

clean these areas gap

ST707

JUMBO

TIP

.03 (0.8 mm) .48 (12.2 mm)

.06 (1.5 mm) .48 (12.2 mm)

.02 (0.5 mm) 1.13 (28.8 mm)

.07 (2.0 mm) .93 (23.6 mm)

.03 (0.8 mm) .48 (12.2 mm)

.10 (2.5 mm) .74 (18.8 mm)

.06 (1.5 mm) 1.21 (30.7 mm)

.04 (1.0 mm) 1.21 (30.7 mm)

.20 (4.9 mm) .93 (23.6 mm)

.32 (8.3 mm) .97 (21.1 mm)

CHANGING TIP

1. MAKE SURE YOUR TOOL IS COOL!

2. Turn Retaining Sleeve counter-clockwise to remove.

3. Remove old Soldering Tip.

4. Insert new Tip.

5. Install Retaining Sleeve. (should be "nger" tight only.)

SOLDERING TIPS

Iron Plated for long life•Nickel and Chrome Plated for optimum heat transfer

CONTACT EDSYN FOR MORE SELECTIONS AB

Large and heavy tip for

heavy duty soldering.

Fine point tip for

SMD soldering.

LT374 Standard Probe

LT375 Standard Spade

LT392 Extra-Long Needle Point

LT394 Extra-Long Spade

LT446 SMD Probe

LT337BC Heavy Duty Terminal Spade

LT223BC Heavy Duty Fine Spade

LT222BC Extra long Needle Point

LT153BH Jumbo Spade

LT155BH Jumbo Angle Spade

SET-UP & REQUIRED ACCESSORIES FOR HEAVY DUTY AND JUMBO TIPS

Apply

AN112 or AN122* Anti-Seize

Compound

to Heater and area of Tip contact.

"BC"

HEAVY DUTY TIP

AC735

RS351

RS271

*AN122 Anti-Seize Compound comes in syringe dispenser.

DO NOT USE the soldering tool if soldering tip is loose. This will cause the heater element to break.

Retaining Sleeve

RS372- for General Purpose Tip

RS271- for Heavy Duty Tip

Soldering Tip

912

1B 1C

22J

22A

22D

22C

22B

22H

22G

22F

22I

22E

951SX-230 LONER® SOLDERING STATION

SPARE PARTS LIST

1 PD528 Tool Pod 1

1A SR042 Thermal Housing for Tool Pod 1

1B SC581 Solder Collector for Tool Pod 1

1C SR043 Front Housing for Tool Pod 1

2 SH230 General Purpose Sponge Holder 1

2A RS199 Cleaning Sponge 1

2B RS243 Leveling Pad for SH230 1

2C LN230 Liner for SH230 1

2D SH230-1 Sponge Holder Tray 1

3 SR302 Control Panel Label 1

4 SR452 Power Switch, DPST 1

5 SR045 Knob, Temperature Control 1

6 SR243 5K Potentiometer, Temperature Control 1

7 SR015 Flat Head Screw- Slotted #6 - 32 x 1/2 4

9 SR017 Hex Nut- #6 - 32 4

10 SR244 Top Case 1

11 SR019 Dove Tail Mount 1

12 15222W95 Circuit Board 1

13 SR573 LED Assy. 1

14 SR611 Bottom Base 1

15 SR011 Pan Head Screw- Phillip #6 - 18 x 5/8 5

16 SR054 Bottom Weight 1

17 POWER CORD ASSY. POWER CORD ONLY 1

SR547 for 951SX-230P SR163 for 951SX-230P

SR548 for 951SX-230 SR318 for 951SX-230

SR549 for 951SX-230B SR454 for 951SX-230B

SR580 for 951SX-230I SR026 for 951SX-230I

18 SR251 Rubber Foot 4

19 SR226 Strain Relief Block for Tool Cord 1

20 SR241 Strain Relief for Power Cord 1

21 SR543 Fuse, 250V, 1 A (5mm x 20 mm) 1

22 SR336 Soldering Tool, Complete Assembly 1

22A SR057 Handle for Tool 1

22B SR058 Cord Strain Relief 1

22C SR546 Tool Cord Assy., Burn Proof 1

22D SR337 Heater Element Assembly Kit (O-Ring (22E) & Collar (22g) Included 1

22E SR062 O-Ring 1

22F SR063 Vinyl Sleeve 1

22G SR064 Collar 1

22H LT375 LONER® Standard Spade Tip 1

22I RS382 Retaining Sleeve 1

22J RB386 Retaining Bushing 1

22K SR525 Silicone Hose, Low Static (sold per foot) 5-1/4"

23 SR053 Strain Relief for Tool Cord 1

24 SR255 Spacer for Potentiometer 1

25 SR310 Label, Calibration Pot, Right Front or Left Rear 1

ITEM

NO. PART NO. DESCRIPTION QTY

REQ'D

951SX-230 instruction manual

THE NAMES LONER, SOLDAPULLT, SOLDAVAC, ATMOSCOPE

AUTO-VAC, IDLE-REST, PIXTER, FUMINATOR, OCTAVAC AND KLATCH

ARE REGISTERED TRADEMARKS OF EDSYN, INC.

MOST PRODUCTS ARE COVERED BY U.S. AND

FOREIGN PATENTS AND PENDING APPLICATIONS.

DESIGN, COLOR AND MATERIALS

SUBJECT TO CHANGE WITHOUT NOTICE.

TIP STYLE ON SOLDERING, DESOLDERING AND HOT AIR TOOLS MAY VARY.

PRINTED IN U.S.A.

NO PART OF THIS PUBLICATION INCLUDING THE INDIVIDUAL ICONS

MAY BE REPRODUCED OR UTILIZED IN ANY FORM OR BY ANY MEANS

WITHOUT THE PERMISSION OF EDSYN, INC.

951SX-230i .pdf

FORM.657 Rev F

Intellectual

Property

Tabla de contenidos

Otros manuales de Pistola de soldar de Edsyn

Edsyn

Edsyn 971E LONER Manual de usuario

Edsyn

Edsyn 971DX-230 Manual de usuario

Edsyn

Edsyn CL1080 LONER Manual de usuario

Edsyn

Edsyn LONER 951SX-H10 Manual de usuario

Edsyn

Edsyn 971-230 LONER Manual de usuario

Edsyn

Edsyn SOLDAVAC VA175 Manual de operación y mantenimiento

Edsyn

Edsyn 971 LONER Manual de usuario

Edsyn

Edsyn LONER 971DX Manual de usuario

Edsyn

Edsyn ZD905 Manual de usuario

Edsyn

Edsyn 981C-230 Manual de usuario

Edsyn

Edsyn LONER 971DF-230 Manual de usuario

Edsyn

Edsyn Loner CL1180 Manual de usuario

Edsyn

Edsyn CL1280 LONER Manual de usuario

Manuales populares de Pistola de soldar de otras marcas

Bakon

Bakon 3200 Manual de usuario

Proxxon

Proxxon Gaslotset MGS Manual de usuario

jbc

jbc SFR-A Manual de usuario

jbc

jbc CL8010 Manual de usuario

HAKO

HAKO FX-8804 Manual de usuario

SATA

SATA 02002A Manual de usuario

Velleman

Velleman HRJA151 Manual de usuario

Weller

Weller WSM 1 Manual de usuario

Vishay Precision Group

Vishay Precision Group Micro-Measurements Mark V Instrucciones de montaje

ersa

ersa i-CON 1V Manual de usuario

Hakko Electronics

Hakko Electronics FX-100 Manual de usuario

Weller

Weller WAD 101 Manual de usuario

Weller

Weller WXD 2 Manual de usuario

AlienTek

AlienTek T100 Manual de usuario

Atten

Atten ATETOOL AT-689A Manual de usuario

Surtek

Surtek 112554 Dimensiones y guía de instalación

Parkside

Parkside PLBS 30 A1 Manual de usuario

BlackJack SolderWerks

BlackJack SolderWerks BK8000 Manual de usuario