EDRO DYNATROL HMI Manual de usuario
The EDRO Corporation
P.O. Box 308
East Berlin, CT 06023 U.S.A. July, 2009
www.edrodynawash.com
PROGRAMMING – OPERATION
PARTS REFERENCE MANUAL
DYNATROL HMI
TOUCH SCREEN CONTROL
For DynaWash Washer-Extractors
Includes DynOzone Programming and Operation
HMI Code 1.00
Technical specifications are based on the latest information available
at the time of printing and are subject to change without notice.
DynaTrol HMI Touch Screen Control
Page 1
TABLE OF CONTENTS
Page
Machine Configuration 2
Motor Setup 4
Water Level Setup 4
Ozone/Signal Setup 5
Timers Setup 5
Miscellaneous Configurable Parameters 6
Language Setup 6
Programming 7
Wash/Rinse Step 8
Drain Step 10
Extract Step 10
Pause Step 11
Link Program 11
End Program 11
Operation 12
Load and Start a Program 12
AutoStart 13
Wash Screen 13
Override Mode 14
Drain Screen 14
Extract Screen 15
Program Complete 15
Alarms and Warnings 16
Reports 17
Alarms 18
Counters 19
Program History 20
Technical Information 21
On Screen Control Manual 21
Debug Screens 22
Settings 24
Passwords 24
Copy Program 25
Reset Factory Programs 25
Clear Program Names 25
Transfer Programs 26
Default Factory Programs 26
HMI System 27
Set System Time 27
Calibrate Screen 27
Download Port 27
Backlight 27
HMI Configuration Settings 27
Parts Reference 28
DynaTrol HMI Touch Screen Control
Page 2
The DynaTrol touch screen control features the latest HMI (Human Machine Interface)
control technology. It is based on a Programmable Logic Controller using ladder logic
code. Use of DynaTrol can be broken down into the following categories:
•Machine Configuration
•Wash Formula Programming
•Operation: Worker and Supervisor Modes
•Managerial Reports on Operation
•Technical Information and Troubleshooting
•Settings
The DynaTrol touch screen control can be setup to work on any DynaWash®washer-
extractor. It must be properly configured to take full advantage of its capabilities.
MACHINE CONFIGURATION
To enter Machine Configuration, press the Configuration button from the Home screen,
then select Machine Configuration. You will need a Level 3 password to continue.
Once you have entered Machine Configuration, you will need to assign a machine series
type:
DynaTrol HMI Touch Screen Control
Page 3
Select a model:
DynaTrol HMI Touch Screen Control
Page 4
The next screens contain information on specific machine parameters which provide
unique model characteristics. They are broken down into the following sub sections:
•Motor Setup
•Water Level Setup
•Ozone / Signal Setup
•Timers Setup
•Miscellaneous Configurable Parameters
A help button is located next to each parameter which further describes the
necessary input or provides a means to set the value.
Enter or change a value by pressing the corresponding number box on the right side of
the screen. A popup window will appear with the current parameter value. Enter a new
value and press ENT to accept, CLR to clear and the X to return without saving.
MOTOR SETUP
Configures motor design and speed settings for the machine.
WATER LEVEL SETUP
Configures values which are affected by level sensing.
DynaTrol HMI Touch Screen Control
Page 5
OZONE/SIGNAL SETUP
Configures DynOzone system and signals working parameters:
TIMERS SETUP
Configures values which are affected by timers.
DynaTrol HMI Touch Screen Control
Page 6
MISCELLANEOUS CONFIGURABLE PARAMETERS
Configures miscellaneous parameters.
LANGUAGE SETUP
To choose Language, press the Configuration button from the Home screen. Then
select the Language button. A level 4 password is required to enter.
Select an available language. This will change all screens except technical information
screens to the selected language. Technical information screens are by default English.
DynaTrol HMI Touch Screen Control
Page 7
PROGRAMMING
The DynaTrol touch screen allows for the entry of up to 50 wash programs with 25 steps
per program, as well as the ability to link programs. Wash programs may contain any of
the following:
•Wash / Rinse Step
•Drain Step
•Extract Step
•Pause Step
To enter Wash Programming, press the Configuration button from the Home screen.
Then select the Wash Programming button. A Level 2 password is required to enter.
Begin by selecting a wash program number. Use the + / - buttons to scroll. Program
names appear in the text box. Twenty factory programs are preloaded. These may be
edited, deleted or re-loaded. To edit name, press the text box.
From this screen you can select a program, change program name, return to previous
menu, delete program, or edit program. To delete, press delete button. This action
cannot be undone. To begin or edit program, press edit for programming options.
DynaTrol HMI Touch Screen Control
Page 8
The main wash programming screen contains six operations:
•Wash / Rinse
•Extract
•Drain
•Pause
•Link Program
•End Program
Press the blue box button next to the operation you wish to perform. A blue operation
box indicates the current step function. From this screen you can press the return button
which will load a program summary screen, delete button which will delete a step, insert
button which will insert a step, or edit button to edit the step.
WASH / RINSE Step
A Wash / Rinse step may contain the following operations: Water fill, temperature
control; rotation control; DynOzone control; and signal control. A time must be entered
for any wash / rinse step.
WATER FILL
Press Cold to activate cold valve; Hot for hot valve, and Reuse for optional reuse valve.
Water fills can be programmed to level and temperature with level being the determining
completion factor.
DynaTrol HMI Touch Screen Control
Page 9
TEMPERATURE CONTROL
Programming a temperature and the Heat button will activate the heating device. This
setting will be maintained for the duration of the step.
ROTATION CONTROL
The step programmable wash cadence is set to a default standard wash rotation. By
pressing the Rotation button a screen with six options will appear. The setting is step
local. Available selections include: Standard Wash; Delicate Wash; Fluff; Forward Only;
Reverse Only; No Rotation. When selecting Standard Wash, Delicate Wash, or Fluff a
new screen will popup with default settings which can then be accepted or modified.
DYNOZONE CONTROL
Selecting the Ozone button will activate the DynOzone system during the wash step.
System will start based on the configured step start parameters and continue for the
duration of step.
SIGNAL CONTROL
Up to 10 signal outputs (depending on model) may be programmed per step. A popup
screen allows for global naming of the signal as well as time entry. A signal time cannot
exceed step time.
Tabla de contenidos
Manuales populares de Pantalla táctil de otras marcas
Elecro Engineering
Elecro Engineering Poolsmart Plus Instrucciones de instalación
Johnson Controls
Johnson Controls IQ4 HUB Manual de usuario
Elo TouchSystems
Elo TouchSystems ET2270L Manual de usuario
Elo TouchSystems
Elo TouchSystems ET1002L Manual de usuario
Elo TouchSystems
Elo TouchSystems 3201L Manual de usuario
Duratec
Duratec S15 Manual de usuario
