Edin Univox Digi RS-ST Manual de usuario

User guide

Univox Digi RS-ST

Digital stationary transmitter

Part no 550020

Content

Introduction�� 2

Product overview�� 3

Display overview�� 4

Connecting instruction�� 5

Bluetooth connection�� 5

Operating instruction �� 6

Compatible receiver Digi RS �� 7

Application�� 8

Troubleshooting��10

Maintenance��11

Warranty��11

Safety��11

Environment��11

Technical data��12

Introduction

Thank you for choosing a Univox product! We hope you will be satisﬁed� Univox Digi RS-ST

stationary transmitter is used where you have an audio source that you want to transfer

wirelessly to receivers with headphones or neckloop�

Digi RS is suitable for a variety of applications, such as teaching, seminars, meetings,

simultaneous interpretation, product demonstrations, talks, sermons, workout etc�

The basic model for Digi RS stationary transmitter comes with frequencies 821 - 832 and

863 - 865MHz, but it is also available in other frequency ranges for use both in and out of

the EU�

A Front panel

A1� Power button

A2� 3�5mm headphone/headset-mic jack

A3� Bluetooth button

A4� Headphone volume control

A5� Mic (Transmitter) / Feed (Interpreter O/I)

button

B1� Rod antenna (TNC connector)

B2� Bluetooth sensor

A3� 6�3mm daisy chain output

B4� 6�3mm daisy chain input

B5� RCA mix output

B6� RCA aux input

A6� Mic level control

A7� OLED Display

A8� Menu / Set jog dial

A9� Aux (Transmitter) / Feed Thru (Interpreter O/I)

button

A10� Aux-in level control

B7� Combo input (XLR/6�3mm)

B8� Switch setting (Line/Mic/Phantom)

B9� Uploading port (not activated)

B10� DC jack

B11� Cable clamp

B Rear panel

9876543

98765

Product overview

C1� Mode

- Transmitter (default)

- Interpreter O (to work with okayo’s 10-way Language Router LR-10)

- Interpreter I

C2� RF signal power

- Low (default)

- Mid

- Hi

C3� Audio level

- Fluctuates with audio signal

C4� Aux-in level

- Low

- Hi (default)

C5� Channel lock

- Channel will be locked automatically when the transmitter is on

C6� Channel number

- Default channel is CH01� Total channel quantity varies with productversion�

- To enter the setting menu, press and keep pressing the jog dial (A8) when turning the

transmitter on�

- Turn the jog dial clockwise to select preferred setting and then press the jog dial

again to conﬁrm new selection and return to setting menu�

- To exit the setting menu, select “Save and Exit” and press the jog dial again�

Display overview

C Standby screen

Setting screen

Connecting instruction

1� Connecting appropriate RCA cable with the transmitter

2� Connecting microphone/line with the transmitter� Switch to MIC or

Line�

3� Connecting the transmitter with supplied power adapter and fasten

the cable well with cable clamp�

4� Compiling channels before operating� (Not active in this model)

5� Connecting the transmitter with active speaker or ampliﬁer�

6� Connecting with next transmitter for daisy chain connection�

7� Connecting the transmitter with supplied TNC rod antenna�

8� Connecting to Bluetooth device, see below�

7 6 54

Bluetooth connection

Push the BT button in the front panel to activate the Bluetooth option� When the BT

button is ﬂashing blue the Digi RS-ST transmitter is “discoverable” for any Bluetooth device

you may want to connect – smartphone, laptop, tablet etc� Make sure that Bluetooth

is activated on your device and ﬁnd the transmitter (“DST 07”) in the list of available BT

signal sources in your device (Settings/Connection/Bluetooth)� Select the DST 07 device

in the list and the BT button will light steadily blue� The connection is now established� To

transmit the BT signal, the “Feed thru” option must be selected� This is done by pushing

the Feed thru button (A9) to ON position (LED lights green)�

Note! As the Digi RS system is mainly designed to capture speech and enhance speech

intelligibility for hearing impaired, music may not sound as full as in the original sound

source� This is normal and not a fault�

Operating instruction

Mode: Transmitter

• Turn the transmitter on

Press the power button for 1 second to turn the transmitter on�

• Unlock the channel

Channel will automatically be locked when the transmitter is on� Press and keep

pressing the jog dial until lock symbol disappears� Then, turn the jog dial clockwise

to select preferred channel number which will be locked when the jog dial is pressed

again�

• Check channel frequency

Press the jog dial shortly when the transmitter is in standby to check the frequency of

selected channel�

• Monitor audio via headphones

Connect 3�5mm headphones or headset mic and tune the volume control at

appropriate position to monitor audio on the transmitter� Note! All audio signals except

mic-in can be monitored�

CAUTION! Listening at high volume for long periods may damage your hearing�

• Activate mic/aux function

Press the mic/aux button to activate or deactivate the function� Tune the mic/aux level

to appropriate position via the control� Note! When headset mic is in use, make sure

mic volume is appropriately adjusted in addition to aux volume�

• Turn the transmitter oﬀ

Press the power button for 2 seconds to turn the transmitter oﬀ�

Advanced operation (Mode: Interpreter O/I)

In addition to standard mode (Transmitter), two additional modes (Interpreter O and

Interpreter I) are also available� For multi language (more than 2) an optional language

router LR-10 is required (order item)�

• Interpreter I (manual)

If only 1 or 2 language interpretation is required, the product can be manually operated

with the Feed or Feed Thru switch�

• Interpreter O (automatic)

Connect it with 10-way language router LR-10 (order item) when this mode is

selected� Both Feed and Feed Thru button will automatically be activated during the

operation of language router LR-10�

Compatible receiver Digi RS

Interface

1� External antenna

2� Power/Signal indicator

- Steady blue: Signal is received with full power

- Steady red: Signal is received but battery is running low

- No LED: No signal is received

3� Battery status

4� Channel lock

- To release the receiver from lock mode, press both up and down (7) buttons

simultaneously until lock symbol disappears�

5� Selected channel

- When the receiver is in unlock mode, press the up or down button (7) to select same channel

as that of the transmitter’s� Press power/set button (8) again or leave it for 5 seconds to

conﬁrm the newly selected channel�

6� Volume wheel

7� Up/Down buttons

8� Power/Set button

- Press and hold this button for 1 second to turn the receiver on�

- Press and hold this button for 2 seconds to turn the receiver oﬀ�

9� Earphone jack

AMPLIFIER

CH05

CH01

FLOOR IN

CH01

(Feed Thru) (Feed Thru)

CH01 CH03 CH05

(Feed)

CH03

10-way language router LR-10

Application

Conferencing/Assistive listening

(Mode: Transmitter)

Interpretation for multi-languages

(Mode: Interpreter O)

AMPLIFIER

CH05

CH01

FLOOR IN

CH01

(Feed Thru) (Feed Thru)

CH01 CH03 CH05

(Feed)

CH03

10-way language router LR-10

CH01 CH02

CH01

CH02

FLOOR

(Feed) (Feed)

AMPLIFIER

Interpretation for 1-2 languages

(Mode: Interpreter I)

Troubleshooting

Why can’t I turn the transmitter on?

• Check if the transmitter is connected to power�

Why can’t I hear anything from the bodypack receiver?

• Check if the bodypack receiver is turned on�

• Check if selected channel on both transmitter and receiver is the same�

• Check if the volume of the bodypack receiver is tuned at appropriate level�

• Check if the bodypack receiver is located within the operation range of the transmitter�

Why can’t the transmitter send audio signal?

• Check if the input signal is properly connected to the transmitter�

• Check if the mic/aux level is tuned at appropriate level�

Why is the operation range shorter?

• Check if the attached antenna is properly connected�

• Check if the audio level is adjusted correctly�

• Adjust the RF power in the setting menu�

Tabla de contenidos

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario