Edimax ES-3116RE+ Manual de usuario

16-Port 10/100Mbps

Smart Switch

(VLAN, Trunking & Fiber Option)

ES-3116RE+

User’s Manual

FCC Class B Certification

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following conditions:

1.This device may not cause harmful interference, and

2.This device must accept any interference received, including

interference that may cause undesired operation.

Warning!

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the distance between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different

from the one which the receiver is connected to.

• Consult the dealer or an experienced radio/TV technician for

help.

You are cautioned that changes or modifications not expressly

approved by the party responsible for compliance could void your

authority to operate the equipment.

1.Introduction

Congratulations on your purchase of this 16-port Smart Fast

Ethernet Switch. This high performance switch provides sixteen

fast ethernet ports to segment network traffics, extend fast ethernet

connection distance, and convert data packets between different

transmission speeds.

This Switch provides sixteen shielded RJ-45 ports. These are

10BaseT/100BaseTX Auto-negotiation ports.

This switch utilize stored-and-forward switching architecture

that filters and forwards data after the complete data packet is

received and examined to be free of errors. With one set of status

LEDs for each individual port, the switch operation status can be

easily monitored.

It’s rackmount design that can be mounted on the industrial

standard 19 inches rack in the enterprise wiring center.

This switch supports both full & half duplex on all ports which

are able to provide 200Mbps of bandwidth to the connected devices,

with auto-negotiation providing smooth migration from Ethernet to

Fast Ethernet. It also supports backpressure and IEEE 802.3x

advanced flow control capability that can reduce congestion and

prevent packet loss.

And it offers advance features :

VLAN : Port based VLAN allows you to set virtual

LANs within your network

Trunking : Reduce the bottleneck between swtiches

Fiber Option : Provide one fiber module option

2.Features & Specifications

(1) Features

Comply with IEEE 802.3 10BaseT and IEEE 802.3u

100BaseTX Standards.

Provide 16 UTP ports with 10/100Mbps Auto-Negotiation.

Provide one uplink port which can connect to another

hub/switch using a normal UTP cable

One 100Mbps Fiber-SC/ST module option (Support

Full/Half Duplex)

Support IEEE 802.3x compliant full-duplex flow control,

half-duplex flow control

Full wire speed on every port.

Support Port-based VLAN

Support 2 Trunking Group

Standard 19” rackmount size.

Support store-and-forward switching architecture.

(2) Specifications

Standards : IEEE 802.3 10BaseT and IEEE 802.3u

100BaseTX

10/100Mbps Ports : RJ-45 x 16

Uplink Port : RJ-45 x 1

100Mbps Fiber-SC/ST Port : Optional

Switching Architecture : Store and Forward

MAC Address : 8K

Buffer : 512Kbyte

Flow Control : Back pressure and IEEE 802.3x

VLAN : Port-based VLAN up to 16 groups

Trunking : 2 groups

N-Way Auto-Negotiation : on all ports

Full-Duplex / Half-Duplex : on all ports

Switch LED : Power

Port LEDs : Link/Activity, 100M, Collision/Full-Duplex

Power : 100~240V AC, full range internal power

Emission : FCC Class B , CE Mark , C-tick

3.Package Contents

One Fast Ethernet Switch

One Power Cord

One User’s manual

Rackmount accessories

4.Physical Description

(1) Panel

Front View

Control Button

LED

Rear View

SWAC 100-240V

POWER

Power Connector

Power Switch

RJ-45 Connectors

Expansion Slot

LED/Button Panel

Power LED

Setup

Buttons

Setup Functions

Normal : Link / Activity

Setu

: Status

Normal : 100Mbps

Setu

: Port

Normal : Full Duplex / Collision

Setu

: Grou

(2) LED

LED Status Description

On Power is supplied

System Power Off No Power

On Collision detected in

this segment

FUL/COL

(Full Duplex/Collision) Off No Collision

On A valid link is

established

Flash Data packets

received

LNK/ACT

(Link/Activity)

Off No link is established

On This port run at

100Mbps

Normal

Port

100M

(100Mbps) Off No connected or run

at 10Mbps

On This group is in

setting mode

Group Off This group is not in

setting

On This port is in setting

mode

Port Off This port is not in

setting mode

On This port is selected

Setup

Status

Status Off This port is not

selected

On VLAN is in setting mode

VLAN Off VLAN is not in setting mode

On Trunking is in setting mode

TRUNK Off Trinking is not in setting mode

On Speed is in setting mode

10/100M Off Speed is not in setting mode

On Full/Half duplex is in setting

mode

FULL/HALF Off Full/Half duplex is not in

setting mode

On Save function is in setting

mode

Setup

Function

SAVE Off Save function is not in setting

mode

5.Installation

(1) Operating Environment

This 16 ports smart switch must be installed and operated

within the limits of specified operating temperature and humidity

(see previous section under Specifications). Do not place objects on

top of the unit. Do not obstruct any vents at the sides of the unit. Do

not position the unit near any heating source such as heater, radiator,

or direct exposure to sun. Prevent entering of water and moisture

into the unit. If necessary, use dehumidifier to reduce humidity.

(2) Connecting network devices

The RJ-45 ports on the switch are designed as MDI-X ports

which allow using straight-through cables to connect this switch to

workstation or hub’s uplink port (MDI). A crossover cable must be

used to connect the switch directly to a hub’s regular port.

Connect one end of the network cable to the RJ-45 port on the

front panel, and connect the other end of the network cable to the

RJ-45 port on the network device. Follow the same procedure to

connect all the RJ-45 ports of the switch. The UTP network cables

must comply with EIA/TIA 568 specifications and Category 5

standard for 100Mbps data transmission. Maximum length, using

UTP cable, between the switch and connected device is 100 meters

(300ft). Once the network cable is connected to both ends and the

attached network device is powered on, the green LNK/ACT LED

should be lit.

An uplink port is located right next to the 16th port of this switch. The

uplink port is a shared port with the 16th port but provides the MDI

connecting to another hub/switch using regular straight-through cables.

Otherwise if you have bought our fiber option module that you can expansion to 1.5k

meters (5000ft) between the switch and connected device.

(3) Connecting the power

Connect the power cord to the power socket on the rear panel of

the unit. Connect the power cord to the power outlet and turn on

power switch. The Power LED on the front panel should be lit.

6.Advance Configuration

This switch provides advance features which offer you more

flexibility in setting up your network. The following section explain

how to setting up the VLAN, Trunking, Speed and Full/Half duplex

modes.

(1) VLAN

Virtual LAN (VLAN) is a logical subgroup within a local area

network which can be configure through port configuration. VLAN

can be configured to optimize traffic or to isolate specific

workstations for reasons of security or convenience. Each VLAN

you configure behaves as an isolated broadcast domain just as if it

were a separate switch. There is no communication between ports on

the separate VLANs unless the VLANs are connected by an external

router.

VLAN Configuration

This Switch provides sixteen VLAN groups. Please refer to the

following procedure to configure VLAN：

VLAN Group 3

VLAN Group 2

VLAN Group 1

Step 1. Press the Function button until the VLAN LED is on.

Step 2. Press the Group button to scroll between the VLAN groups 1 to 16.

Step 3. Press the Port button to scroll between the port 1 to 16.

Tabla de contenidos

Otros manuales de Cambiar de Edimax

Edimax

Edimax GS-5008E Manual de usuario

Edimax

Edimax ES-3205P Manual de usuario

Edimax

Edimax ES-5160G+ Manual de usuario

Edimax

Edimax GS-1026 Manual de usuario

Edimax

Edimax ES-3105P Manual de usuario

Edimax

Edimax ES-5424P Manual de usuario

Edimax

Edimax Two-console 16 port PS/2 KVM Switch Manual de usuario

Edimax

Edimax SP-1101W Manual de usuario

Edimax

Edimax EK-2U2C Manual de usuario

Edimax

Edimax 9-Port Desktop Ethernet Hub ER-5390S Manual de usuario

Edimax

Edimax EK-UA2C Manual de usuario

Edimax

Edimax GS-1016 Manual de usuario

Edimax

Edimax EU-HB4S Manual de usuario

Edimax

Edimax EK-PA2C Manual de usuario

Edimax

Edimax SP-2101W V3 Manual de usuario

Edimax

Edimax USBH-004 Manual de usuario

Edimax

Edimax ES-3116RL Manual de usuario

Edimax

Edimax GS-5654LX Manual de usuario

Edimax

Edimax EK-08RE Manual de usuario

Edimax

Edimax 16 Port Nway Fast Ethernet PoE Web Smart... Manual de usuario

Edimax

Edimax ES-516G+ Manual de usuario

Edimax

Edimax HP-5101ES Manual de usuario

Edimax

Edimax EK-16RE Manual de usuario

Edimax

Edimax EK-2U2CA Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario