Edge Lighting Cody 12" Manual de usuario

ARM

1.5MM ALLEN

WRENCH

M3 SET SCREW

SWIVEL

CONNECTOR

Installation Instructions for Cody 12" Canopy Mount Picture Light

904-CPL-12-01

Install the Fixture

CPL-12-_

1718 W. Fullerton Ave

Chicago, IL 60614

Tel: 773-770-1195

Fax: 773-935-5613

www.edgelighting.com

[email protected]

1: Rotate the Cody's head perpendicular to the arm making

sure the arm is completely inserted into the head swivel

connector. Tighten the M3 set screw on the swivel connector

with the provided 1.5mm Allen wrench to secure the head in

place.

SAVE THESE INSTRUCTIONS!

- This product is ETL listed for indoor location.

- This product is wall mounted only.

- This product can mount to either a 4" square electrical box

with round plaster ring or an octagon electrical box.

- This instruction shows a typical installation.

IMPORTANT INFORMATION

HEAD

ARM

1.5MM ALLEN

WRENCH

M3 SET SCREW

SWIVEL

CONNECTOR

HEAD

2: Insert the loose arm assembly (provided in the box) into the

other swivel connector, insert the joining arm into the

mounting bracket of the first arm. Tighten the M3 set screw

on the swivel connector with the

1.5mm Allen wrench.

and mounting bracket

HEAD

ARM

JOINING ARM

MOUNTING BRACKET 2

MOUNTING BRACKET

ANCHOR

WALL

ELECTRICAL

BOX

3: Hold the two mounting brackets against the wall above the

electrical box. Using a level, align the mounting brackets

and mark the four bracket holes on the wall.

4: Tap the anchors onto the marked points into the wall up to

the threaded portion with a hammer.

5: Screw the threaded portion of the anchors in with the a

Phillips screwdriver.

NOTE: The Cody 12" canopy mount must be installed right

above the electrical box.

LED POWER SUPPLY

WIRE NUT

ELECTRICAL BOX

6: Connect the white LED power supply wire to the neutral

power wire with a wire nut.

7: Connect the black LED power supply wire to the hot power

wire with a wire nut.

8: Place the LED power supply and all wire connections inside

the electrical box.

CROSSBAR

ASSEMBLY

#8-32 SCREW

ELECTRICAL BOX

POWER WIRE

9: Mount the crossbar assembly to the electrical box holes with

the provided #8-32 screws.

#8 SCREW

MOUNTING BRACKET

ELECTRICAL BOX

10: Line up the mounting bracket holes with the anchors and

secure the fixture to the anchors with the four #8 screws

provided.

ANCHOR

ARM

2MM ALLEN WRENCH

M4 SET SCREW 11

11: To adjust the height, loosen the four M4 set screw on

the mounting brackets with the provided 2mm Allen

wrench. Adjust the Cody to the desired height by sliding it

up or down. Tighten the four M4 set screws with the 2mm

Allen wrench.

MOUNTING BRACKET

11 H

THUMB

NUT

CUTOUT

14 13

12: Connect each low voltage LED power supply wire (red

wire) to one fixture wire with a wire nut.

13: Place the excess wires and wire nuts inside the electrical

box.

14: Line up the canopy cut out edge with the fixture wires.

Place the canopy onto the electrical box and tighten the

thumb nut to the crossbar assembly nipple.

15: Hang the frame cable into the two mounting bracket slots.

IMOUNTING BRACKET SLOT

FRAME CABLE

NOTE: The Cody 12" contains 12 watt integrated LED lamps.

These lamps are rated for 50,000 hours.

16: Rotate the fixture head to properly wash the picture with

light.

FIXTURE HEAD

PICTURE 16

15 15

Este manual sirve para los siguientes modelos

Otros manuales de Luminaria de Edge Lighting

Edge Lighting

Edge Lighting Cody CPL-6-P Series Manual de usuario

Manuales populares de Luminaria de otras marcas

Emos

Emos CLASSIC ZY1431T Manual de usuario

Westinghouse

Westinghouse Outdoor Lighting Fixture Manual de usuario

Hedler

Hedler C 12 silent Manual de usuario

Blizzard Lighting

Blizzard Lighting Puck: CSI Manual de usuario

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manual de usuario

Lightmaxx

Lightmaxx Shaft 5R Manual de usuario

Triarch

Triarch 31083 Manual de usuario

Philips

Philips 32614 Series Manual de usuario

IKEA

IKEA TIVED Manual de usuario

Lightolier

Lightolier LP200 Manual de usuario

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manual de usuario

Martin

Martin MAC 250 Krypton Manual de usuario

Cooper Lighting

Cooper Lighting Halo L3232E Manual de usuario

Stageline

Stageline ODW-2410RGBW Manual de usuario

Light Sky

Light Sky Tornado Series Manual de usuario

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manual de usuario

Lightolier

Lightolier Lytespan 83ED17S Manual de usuario

Lightolier

Lightolier Calculite CS8226 Manual de usuario