Edge-Core ECS4110-28T Manual de programación

Management Guide

www.edge-core.com

ECS4110-28T/28P/52T/52P

28/52-Port Gigabit Ethernet

Layer 2+ Switch

ANAGEMENT

UIDE

ECS4110-28T GIGABIT ETHERNET SWITCH

Layer 2+ Managed Switch

with 24 10/100/1000BASE-T (RJ-45) Ports,

and 4 Gigabit SFP Ports

ECS4110-28P GIGABIT ETHERNET POE SWITCH

Layer 2+ Managed Switch

with 24 10/100/1000BASE-T (RJ-45) PoE Ports,

and 4 Gigabit SFP Ports

ECS4110-52T GIGABIT ETHERNET SWITCH

Layer 2+ Managed Switch

with 48 10/100/1000BASE-T (RJ-45) Ports,

and 4 Gigabit SFP Ports

ECS4110-52P GIGABIT ETHERNET POE SWITCH

Layer 2+ Managed Switch

with 48 10/100/1000BASE-T (RJ-45) PoE Ports,

and 4 Gigabit SFP Ports

E072014/ST-R02

150200000929A

– 5 –

ABOUT THIS GUIDE

PURPOSE This guide gives specific information on how to operate and use the

management functions of the switch.

AUDIENCE The guide is intended for use by network administrators who are

responsible for operating and maintaining network equipment;

consequently, it assumes a basic working knowledge of general switch

functions, the Internet Protocol (IP), and Simple Network Management

Protocol (SNMP).

CONVENTIONS The following conventions are used throughout this guide to show

information:

OTE

Emphasizes important information or calls your attention to related

features or instructions.

AUTION

Alerts you to a potential hazard that could cause loss of data, or

damage the system or equipment.

ARNING

Alerts you to a potential hazard that could cause personal injury.

RELATED PUBLICATIONS The following publication details the hardware features of the switch,

including the physical and performance-related characteristics, and how to

install the switch:

The Installation Guide

Also, as part of the switch’s software, there is an online web-based help

that describes all management related features.

BOUT

HIS

UIDE

– 6 –

REVISION HISTORY This section summarizes the changes in each revision of this guide.

JULY 2014 RELEASE

This is the second version of this guide. This guide is valid for software

release v1.1.2.0. It includes information on the following changes:

◆Adds information for the ECS4110-28T and ECS4110-28P.

◆Updated information in Table 1, "Key Features," on page 75.

◆Updated information under "Description of Software Features" on

page 76.

◆Updated information in Table 2, "System Defaults," on page 82.

◆Updated information in Table 6, "Switch Main Menu," on page 106.

◆Added the section "Configuring NTP" on page 139.

◆Added the section "Configuring Time Servers" on page 140.

◆Updated description of Media Type under "Configuring by Port List" on

page 156.

◆Added the section "Displaying Transceiver Data" on page 170.

◆Added Timout Mode under "Configuring a Dynamic Trunk" on page 179.

◆Added the section "Configuring Load Balancing" on page 189.

◆Updated information under "Traffic Segmentation" on page 193.

◆Added description of L3 Interface parameter under "Configuring

VLAN Groups" on page 202.

◆Added description of Mask parameter under "Configuring MAC-based

VLANs" on page 227.

◆Added the section "Configuring MAC Address Learning" on page 231.

◆Updated the parameter list under "Configuring Loopback Detection" on

page 242.

◆Added description of BPDU Flooding and Cisco Prestandard Status

parameters under "Configuring Global Settings for STA" on page 243.

◆Added description of BPDU Flooding and Admin Edge Port parameters

under "Configuring Interface Settings for STA" on page 250.

◆Updated the parameter list under "Configuring a Class Map" on

page 288.

◆Updated the paramter list under "Configuring Local/Remote Logon

Authentication" on page 311.

BOUT

HIS

UIDE

– 7 –

◆Updated the parameter list under "Configuring AAA Accounting" on

page 317.

◆Updated the parameter list under "Configuring AAA Authorization" on

page 323.

◆Updated description of the Access Level parameter under "Configuring

User Accounts" on page 326.

◆Added the section "Setting a Time Range" on page 353.

◆Updated description of Source Address Type and Destination Address

Type parameters under "Configuring an Extended IPv6 ACL" on

page 365.

◆Added Internet Protocol parameter under "Configuring a MAC ACL" on

page 367.

◆Added the section "Configuring ACL Mirroring" on page 372.

◆Added the section "Showing ACL Hardware Counters" on page 374.

◆Added the parameter Allow Zeros under "Configuring Global Settings

for ARP Inspection" on page 376.

◆Updated parameter list under "Configuring Port Security" on page 385.

◆Added the parameter Re-authentication Max Retries under "Configuring

Port Authenticator Settings for 802.1X" on page 390.

◆Updated the parameter list for "DoS Protection" on page 399.

◆Added the section "IPv6 Source Guard" on page 406.

◆Updated the parameter list for "DHCP Snooping Global Configuration"

on page 415.

◆Added the Circuit ID parameter under "Configuring Ports for DHCP

Snooping" on page 417.

◆Added description of time range parameters under "Setting the Port

PoE Power Budget" on page 450.

◆Updated Table 34, "Supported Notification Messages," on page 462.

◆Added the section "Creating SNMP Notification Logs" on page 476 and

"Showing SNMP Statistics" on page 478.

◆Added the sections "Ethernet Ring Protection Switching" on page 495,

"Connectivity Fault Management" on page 520, and "OAM

Configuration" on page 556.

◆Added the Forwarding Priority parameter under "Configuring IGMP

Snooping and Query Parameters" on page 570.

BOUT

HIS

UIDE

– 8 –

◆Added the sections "Filtering IGMP Query Packets and Multicast Data"

on page 584 and "Displaying IGMP Snooping Statistics" on page 586.

◆Added the section "MLD Snooping (Snooping and Query for IPv6)" on

page 595.

◆Added the section "Configuring MVR Global Settings" on page 605.

◆Updated the parameter list under "Configuring MVR Domain Settings"

on page 607.

◆Added the section "Configuring MVR Group Address Profiles" on

page 608.

◆Updated the parameter list under "Configuring MVR Interface Status"

on page 611.

◆Updated the parameter list under "Displaying MVR Receiver Groups" on

page 616.

◆Added the section "Displaying MVR Statistics" on page 617.

◆Added the section "Multicast VLAN Registration for IPv6" on page 621.

◆Added new parameters under "Configuring IPv6 Interface Settings" on

page 644.

◆Added the section "Specifying a DHCP Client Identifier" on page 669.

◆Added the section "Configuring DHCP Relay Service" on page 671.

◆Added the section "Using the Trace Route Function" on page 684.

◆Added the sections "Configuring Static Routes" on page 691 and

"Displaying the Routing Table" on page 693.

◆Updated syntax for the command "show running-config" on page 729.

◆Added the commands "show watchdog" on page 734 and "watchdog

software" on page 735.

◆Updated syntax for the command "copy" on page 738.

◆Updated syntax for the command "delete" on page 741.

◆Added the command "upgrade opcode reload" on page 745.

◆Added "TFTP Configuration Commands" on page 746.

◆Updated syntax for the command "logging host" on page 761

◆Added "NTP Commands" on page 773.

BOUT

HIS

UIDE

– 9 –

◆Added the commands "clock summer-time (date)" on page 777, "clock

summer-time (predefined)" on page 778, and "clock summer-time

(recurring)" on page 779.

◆Updated syntax for the command "snmp-server enable traps" on

page 798.

◆Added the commands "snmp-server enable port-traps mac-notification"

on page 801 and "show snmp-server enable port-traps" on page 802.

◆Updated description of syntax for the commands "enable password" on

page 824 and "username" on page 825.

◆Added commands "privilege" on page 827 and "show privilege" on

page 827.

◆Added the commands "tacacs-server retransmit" on page 836 and

"tacacs-server timeout" on page 837.

◆Added the command "accounting commands" on page 844.

◆Updated syntax for the command "show accounting" on page 846

◆Added the command "dot1x max-reauth-req" on page 866.

◆Added the section "PPPoE Intermediate Agent" on page 880.

◆Added the commands "mac-learning" on page 890, "port security

mac-address-as-permanent" on page 893, and ."show port security" on

page 893.

◆Updated syntax and description for the command "ip dhcp snooping

information option" on page 918.

◆Added the command "ip dhcp snooping limit rate" on page 920.

◆Added the command "ip dhcp snooping information option circuit-id" on

page 922.

◆Added the command "clear ip dhcp snooping binding" on page 924.

◆Added the section "DHCPv6 Snooping" on page 926.

◆Updated syntax for "ip source-guard binding" on page 936 and "ip

source-guard max-binding" on page 939.

◆Added the command "ip source-guard mode" on page 940.

◆Added the command "clear ip source-guard binding blocked" on

page 941.

◆Updated syntax for "show ip source-guard binding" on page 942.

◆Added the section "IPv6 Source Guard" on page 943.

BOUT

HIS

UIDE

– 10 –

◆Added allow-zeros parameter to the command "ip arp inspection

validate" on page 952.

◆Added new commands under the section "Denial of Service Protection"

on page 957.

◆Added new commands under the section "Port-based Traffic

Segmentation" on page 963.

◆Added counter parameter to the commands "ip access-group" on

page 975, "ipv6 access-group" on page 981, and "mac access-group"

on page 987.

◆Updated syntax for the command "permit, deny (MAC ACL)" on

page 984.

◆Updated syntax for the command "show access-group" on page 992.

◆Added the commands "discard" on page 999 and "show discard" on

page 1004.

◆Updated syntax for the command "media-type" on page 1001.

◆Added commands under "Transceiver Threshold Configuration" on

page 1009.

◆Added the commands "port channel load-balance" on page 1022, "lacp

timeout" on page 1029, and "show port-channel load-balance" on

page 1033.

◆Added the commands "power mainpower maximum allocation" on

page 1036 and "show power mainpower" on page 1042.

◆Added access-list parameter to the command "port monitor" on

page 1045.

◆Added the command "spanning-tree system-bpdu-flooding" on

page 1099.

◆Updated description for the command "spanning-tree bpdu-filter" on

page 1103.

◆Updated description for the command "spanning-tree bpdu-guard" on

page 1104.

◆Added block parameter to the command "spanning-tree

loopback-detection action" on page 1108.

◆Added the command "spanning-tree port-bpdu-flooding" on page 1112

and "spanning-tree tc-prop-stop" on page 1114.

◆Updated syntax for the command "show spanning-tree" on page 1116.

◆Added the chapter "ERPS Commands" on page 1119.

Otros manuales para ECS4110-28T

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Edge-Core

Edge-Core

Edge-Core ES4005V Manual de usuario

Edge-Core

Edge-Core ES3628EA Manual de usuario

Edge-Core

Edge-Core ECS4110-52T Manual de usuario

Edge-Core

Edge-Core AS6700-32X Manual de usuario

Edge-Core

Edge-Core ECS3510-52T Manual de usuario

Edge-Core

Edge-Core ECS4510-12PD Manual de programación

Edge-Core

Edge-Core ES3526YA Manual de usuario

Edge-Core

Edge-Core ES3528M Manual de usuario

Edge-Core

Edge-Core AS4610-30T Manual de usuario

Edge-Core

Edge-Core ECS4650-54T Manual de usuario

Edge-Core

Edge-Core Minipack-AS8000 Manual de usuario

Edge-Core

Edge-Core ES3528-WDM Manual de programación

Edge-Core

Edge-Core ES4308-POE Manual de programación

Edge-Core

Edge-Core ECS4510-28P Manual de usuario

Edge-Core

Edge-Core ECS4310-26T Manual de programación

Edge-Core

Edge-Core AS5610-52X Manual de usuario

Edge-Core

Edge-Core ES4512C Manual de usuario

Edge-Core

Edge-Core ECS2100-10T Manual de usuario

Edge-Core

Edge-Core AS7712-32X Manual del propietario

Edge-Core

Edge-Core AS6712-32X Manual de usuario

Edge-Core

Edge-Core AS9926-24D Manual de usuario

Edge-Core

Edge-Core ECS2020 Series Manual de programación

Edge-Core

Edge-Core AS7535-28XBE Manual de usuario

Edge-Core

Edge-Core AS5916-54XKS Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario