Edge-Core ECS3510-10PD Manual de programación

Management Guide

www.edge-core.com

10-Port Layer 2

Fast Ethernet Switch

ANAGEMENT

UIDE

ECS3510-10PD FAST ETHERNET SWITCH

Layer 2 Switch

with 8 10/100BASE-TX (RJ-45) Ports,

and 2 Gigabit Combination Ports (RJ-45/SFP)

ECS3510-10PD

E032014/ST-R03

149100000179A

– 5 –

ABOUT THIS GUIDE

PURPOSE This guide gives specific information on how to operate and use the

management functions of the switch.

AUDIENCE The guide is intended for use by network administrators who are

responsible for operating and maintaining network equipment;

consequently, it assumes a basic working knowledge of general switch

functions, the Internet Protocol (IP), and Simple Network Management

Protocol (SNMP).

CONVENTIONS The following conventions are used throughout this guide to show

information:

OTE

Emphasizes important information or calls your attention to related

features or instructions.

AUTION

Alerts you to a potential hazard that could cause loss of data, or

damage the system or equipment.

ARNING

Alerts you to a potential hazard that could cause personal injury.

RELATED PUBLICATIONS The following publication details the hardware features of the switch,

including the physical and performance-related characteristics, and how to

install the switch:

The Installation Guide

Also, as part of the switch’s software, there is an online web-based help

that describes all management related features.

BOUT

HIS

UIDE

– 6 –

REVISION HISTORY This section summarizes the changes in each revision of this guide.

MARCH 2014 RELEASE

This is the third release of this guide. This guide is valid for software

release v1.4.2.1. It includes the following changes:

◆Added the command "clock timezone-predefined" on page 771.

DECEMBER 2013 RELEASE

This is the second release of this guide. This guide is valid for software

release v1.4.0.1. It includes the following changes:

◆Updated parameter values under "Configuring the Console Port" on

page 141.

◆Updated parameter values under "Configuring Telnet Settings" on

page 143.

◆Updated description of parameters under "Configuring by Port List" on

page 152.

◆Added timeout parameter under "Configuring a Dynamic Trunk" on

page 177.

◆Added sections "Displaying Transceiver Data" on page 166,

"Configuring Transceiver Thresholds" on page 167, and "Configuring

Load Balancing" on page 187.

◆Added the section "Creating CVLAN to SPVLAN Mapping Entries" on

page 215.

◆Added “priority” parameter under "Mapping Protocol Groups to

Interfaces" on page 221.

◆Added the section "Configuring MAC Address Learning" on page 229.

◆Added new parameters under "Configuring Loopback Detection" on

page 242.

◆Updated description of “Type” parameter and added description of

“CoS” parameter under "Configuring a Class Map" on page 290.

◆Updated description of “Access Level” parameter under "Configuring

User Accounts" on page 328.

◆Added “Counter” parameter under "Binding a Port to an Access Control

List" on page 373.

◆Added the sections "Configuring ACL Mirroring" on page 374 and

"Showing ACL Hardware Counters" on page 376.

◆Added the parameter “Allow Zeros” under "Configuring Global Settings

for ARP Inspection" on page 378.

BOUT

HIS

UIDE

– 7 –

◆Updated parameter list under "Configuring Port Security" on page 387.

◆Added the section "IPv6 Source Guard" on page 409.

◆Updated parameter list under "DHCP Snooping Configuration" on

page 418 and "Configuring Ports for DHCP Snooping" on page 420.

◆Added “UDP Port” parameter under "Remote Log Configuration" on

page 428.

◆Added “MED-Location Civic Address” parameter under "Configuring

LLDP Interface Attributes" on page 433.

◆Added the section "Configuring LLDP Interface Civic-Address" on

page 437.

◆Updated parameter list under "Displaying LLDP Local Device

Information" on page 439 and "Displaying LLDP Remote Device

Information" on page 442.

◆Added the sections "Creating SNMP Notification Logs" on page 477 and

"Showing SNMP Statistics" on page 479.

◆Updated description for ERPS version 2 under "ERPS Ring

Configuration" on page 502, and added the section "ERPS Forced and

Manual Mode Operations" on page 518.

◆Added the sections "Configuring a Remote Loop Back Test" on page 564

and "Displaying Results of Remote Loop Back Testing" on page 566.

◆Added the section "Using the Trace Route Function" on page 571

◆Added description of parameters for RA Guard under "Configuring IPv6

Interface Settings" on page 580.

◆Added the section "Specifying a DHCP Client Identifier" on page 603,

"Configuring DHCP Relay Service" on page 604.

◆Added the section "Configuring the PPPoE Intermediate Agent" on

page 608.

◆Added description of “Multicast Data Drop” under "Filtering IGMP Query

Packets and Multicast Data" on page 632.

◆Updated parameter list under "Displaying Multicast Groups Discovered

by IGMP Snooping" on page 633.

◆Added the section "MLD Snooping (Snooping and Query for IPv6)" on

page 643.

◆Added the section "Multicast VLAN Registration for IPv6" on page 668.

◆Added "TFTP Configuration Commands" on page 736.

BOUT

HIS

UIDE

– 8 –

◆Added the command "terminal" on page 747.

◆Added UDP port parameter for the command "logging host" on

page 751.

◆Added the command "clock summer-time (date)" on page 766, "clock

summer-time (predefined)" on page 768, and "clock summer-time

(recurring)" on page 769.

◆Added “mac-notification” parameter for the command "snmp-server

enable traps" on page 790, as well as the commands "snmp-server

enable port-traps mac-notification" on page 793 and "show snmp-

server enable port-traps" on page 794.

◆Updated description of the “level” parameter under the commands

"enable password" on page 816, and "username" on page 817.

◆Added the command "accounting commands" on page 836.

◆Added the commands "mac-learning" on page 880, and "port security

mac-address-as-permanent" on page 883.

◆Added the command "ip dhcp snooping limit rate" on page 910.

◆Added the commands "ipv6 dhcp snooping option remote-id" on

page 919 and "ipv6 dhcp snooping option remote-id policy" on

page 920.

◆Added MAC and ACL mode options for the commands "ip source-guard

binding" on page 926, "ip source-guard max-binding" on page 929, "ip

source-guard mode" on page 930.

◆Added the command "clear ip source-guard binding blocked" on

page 931.

◆Updated parameter list for the command "show ip source-guard

binding" on page 932.

◆Added the section "IPv6 Source Guard" on page 933.

◆Added “allow zeros” parameter to the command "ip arp inspection

validate" on page 942.

◆Added “counter” parameter to the command "ip access-group" on

page 962, "ipv6 access-group" on page 968, and "mac access-group"

on page 974.

◆Added Layer 3 and 4 parameters to the command "permit, deny

(MAC ACL)" on page 971.

◆Added the command "clear access-list hardware counters" on

page 979, and added the “hardware-counters” parameter to the

command "show access-list" on page 980.

BOUT

HIS

UIDE

– 9 –

◆Added the commands "discard" on page 985 and "show discard" on

page 991.

◆Added the commands "transceiver-monitor" on page 996, "transceiver-

threshold-auto" on page 996, "transceiver-threshold current" on

page 997, "transceiver-threshold rx-power" on page 998, "transceiver-

threshold temperature" on page 999, "transceiver-threshold tx-power"

on page 1000, "transceiver-threshold voltage" on page 1001, and

"show interfaces transceiver-threshold" on page 1003.

◆Added the command "lacp timeout" on page 1017.

◆Added “access-list” parameter to the command "port monitor" on

page 1023.

◆Added the command "spanning-tree tc-prop-stop" on page 1094.

◆Added changes for ERPS version 2 under "ERPS Commands" on

page 1099.

◆Added “priority” parameter to the command "protocol-vlan

protocol-group (Configuring Interfaces)" on page 1158.

◆Updated syntax for "class-map" on page 1188 command.

◆Added “cos” parameter to "match" on page 1190 command.

◆Added commands "clear ip igmp snooping groups dynamic" on

page 1222 and "clear ip igmp snooping statistics" on page 1223.

◆Updated display text for the command "show ip igmp snooping group"

on page 1224.

◆Added the command "ip igmp authentication" on page 1232 and "show

ip igmp authentication" on page 1237.

◆Updated syntax for the command "ip igmp query-drop" on page 1236.

◆Added commands "ip multicast-data-drop" on page 1236 and "show ip

multicast-data-drop" on page 1240.

◆Added sections "MLD Snooping" on page 1241 and "MLD Filtering and

Throttling" on page 1251.

◆Added commands "mvr priority" on page 1264 and "mvr proxy-

switching" on page 1266.

◆Updated parameters for "mvr immediate-leave" on page 1270.

◆Added commands "clear mrv groups dynamic" on page 1273 and "clear

mrv statistics" on page 1273.

◆Updated parameters for "show mvr members" on page 1276 and "show

mvr statistics" on page 1278.

BOUT

HIS

UIDE

– 10 –

◆Updated display text for the command “show mvr statistics query” on

page 1278, and “show mvr statistics summary” on page 1278.

◆Added the section "MVR for IPv6" on page 1283.

◆Added commands "clear efm oam event-log" on page 1374, "efm oam

remote-loopback" on page 1375, and "efm oam remote-loopback test"

on page 1376.

◆Added the section "DHCP Relay Option 82" on page 1397.

◆Updated parameter description for the command "ip address" on

page 1404.

◆Added the section "ND Snooping" on page 1439.

JANUARY 2012 RELEASE

This is the first release of this guide. This guide is valid for software release

v1.3.4.5.

Tabla de contenidos

Otros manuales de Cambiar de Edge-Core

Edge-Core

Edge-Core ES4624-SFP Manual de usuario

Edge-Core

Edge-Core ECS4610-24F Manual de programación

Edge-Core

Edge-Core ECS4310-26T Manual de programación

Edge-Core

Edge-Core ES4524M-PoE Manual de usuario

Edge-Core

Edge-Core AS5912-54X Manual de usuario

Edge-Core

Edge-Core ECS3510-28F Manual de usuario

Edge-Core

Edge-Core ECS3510-52T Manual de usuario

Edge-Core

Edge-Core ES3628EA Manual de usuario

Edge-Core

Edge-Core ECS2100-10T Manual de usuario

Edge-Core

Edge-Core ECS4620-28T Manual de usuario

Edge-Core

Edge-Core ECS4650-54T Manual de usuario

Edge-Core

Edge-Core ES4324 Manual de usuario

Edge-Core

Edge-Core ES3528-WDM Manual de programación

Edge-Core

Edge-Core AS7326-56X Instrucciones de funcionamiento

Edge-Core

Edge-Core ECS4620-28T Manual de usuario

Edge-Core

Edge-Core AS5610-52X Manual de usuario

Edge-Core

Edge-Core AS4610-54T Manual de usuario

Edge-Core

Edge-Core AS6701-32X Manual de usuario

Edge-Core

Edge-Core ECS4510-28P Manual de usuario

Edge-Core

Edge-Core ECS4510-28T Manual de usuario

Edge-Core

Edge-Core ECS2020 Series Manual de programación

Edge-Core

Edge-Core ECS4310-18T Manual de usuario

Edge-Core

Edge-Core ECS3510-26P Manual de usuario

Edge-Core

Edge-Core ECS2100-10T Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario