edesix VIDEOBADGE VB-400 Manual de usuario
VB-400 Series - Quickstart Guide - ED-006-021-08
Wearable Security for Professionals
1
ED-006-021-08
VIDEOBADGE VB-400
QUICKSTART GUIDE
Wearable Security for Professionals
VB-400 Series - Quickstart Guide - ED-006-021-08
2
Wearable Security for Professionals
CONTENTS
INTRODUCTION 3
CHARGING YOUR DEVICE 4
Solo Docking Station (VB-400-SOLO) 5
14 Port Docking Station (VB-400-DOCK14) 6
Battery Status LED 7
CONFIGURING YOUR DEVICE 8
IDENTIFYING AN RFID ASSIGNED BADGE 9
USING YOUR VIDEOBADGE VB-400 10
To Start / Stop recording (Congurable) 10
ACCESSORIES 13
REGULATORY INFORMATION 14
VB-400 Series - Quickstart Guide - ED-006-021-08
Wearable Security for Professionals
3
INTRODUCTION
Welcome, and thank you for choosing Edesix as your Body Worn Camera provider.
This simple guide will lead you through the set-up process of your VB-400 Body Worn Camera
and all accompanying accessories.
Lens
Buzzer
Speaker
Function
Button B
LED
LED
Function
Button C
Slider
Dual
Microphone
Front
Function Button
Function
Button A
LED
VB-400 Series - Quickstart Guide - ED-006-021-08
4
Wearable Security for Professionals
CHARGING YOUR DEVICE
Upon receiving your VB-400 VideoBadge, it is recommended that you fully charge the device before
usage.
When charging using a Solo or 14 Slot docking station, insert the camera into the dock as shown in
the diagram.
Ensure the camera clicks securely in place. Check that the top LED blinks green to indicate charging
Slide down to
click into place
VB-400 Series - Quickstart Guide - ED-006-021-08
Wearable Security for Professionals
5
Once fully charged, the same LED will turn solid green. If the LED is not lit, the device is not charging.
Your VideoBadge will be fully charged within 8 hours from a at battery.
To enable charging you will require one of the following;
Solo Docking Station (VB-400-SOLO)
MConnected to your laptop
If you are charging your VB-400 camera via a Solo Docking Station (VB-400-SOLO) your VideoBadge
will bleep to indicate charging has commenced, and the LED, as indicated, will ash green to show
charging.
View on Top Face
Charging: Flashing green LED
View on Top Face
Fully Charged: Solid green LED
VB-400 Series - Quickstart Guide - ED-006-021-08
6
Wearable Security for Professionals
14 Port Docking Station (VB-400-DOCK14)
MConnected to a power supply and
Dock Controller
If you are charging your VB-400 camera via a 14
Port Docking Station (VB-400-DOCK14) the top
LED will ash green to show charging, and the
camera will bleep when successfully connected to
VideoManager.
View on Top Face
Charging: Flashing green LED
View on Top Face
Fully Charged: Solid green LED
Once fully charged, the same LED will turn solid green. If the LED is not lit, the device is not charging.
Your VideoBadge will be fully charged within 8 hours from a at battery.
VB-400 Series - Quickstart Guide - ED-006-021-08
Wearable Security for Professionals
7
Battery Status LED
To quickly understand the current battery status of your VideoBadge, press the bottom button on
the front face of the camera and refer to the bottom right LED.
Colour Key:
Green LED: OK
Orange/Yellow LED: Low
Red LED: Critical
Battery Status Button
(Congurable)
VB-400 Series - Quickstart Guide - ED-006-021-08
8
Wearable Security for Professionals
CONFIGURING YOUR DEVICE
Prior to using your VB-400 VideoBadge, your
device must be congured and assigned to you
using VideoManager. For detailed information on
how to congure your device, please refer to the
VideoManager User Guide.
Each VideoBadge requires a valid VideoManager
Licence, or access to the Edesix Cloud Service, in
order for you to assign devices and access footage.
For further details, see the VideoManager User
Guide.
To ascertain whether your VideoBadge has been
congured, please view the top left LED on your
device.
This LED will turn solid green once congured and
assigned. Your VideoBadge is charged, assigned
and ready to use when the LEDs shown are both
solid green.
Congured, charged & assigned
Solid green light
Please Note: If you try to use your VideoBadge before it has been assigned, the bottom LED on the
front face of the camera will start to ash red and you will hear an alarm tone.
You will not be able to use your camera until it has been assigned.
VB-400 Series - Quickstart Guide - ED-006-021-08
Wearable Security for Professionals
9
IDENTIFYING AN RFID ASSIGNED BADGE
Once your device is congured, your system administrator may wish badge users to utilise an RFID
system for camera assignment. For further information on using RFID with your VB-400, please refer
to the VideoManager User Guide.
Having presented your RFID card, your docked, assigned VB-400 will identify itself with a solid red
LED as shown.
RFID Assigned Badge
VB-400 Series - Quickstart Guide - ED-006-021-08
10
Wearable Security for Professionals
USING YOUR VIDEOBADGE VB-400
The Edesix VB-400 series of cameras are intuitive and simple to use.
To Start / Stop recording (Congurable)
Users can activate recording by pressing on the single front button located in the centre of the
badge as shown. Recording is stopped by pressing and holding the front button.
Record activation and deactivation buttons are congurable by Administrators.
Start Recording initiated will be indicated by a short bleep, the top right LED showing red and the
top front LEDs showing red.
Solid red LED
Press centre button to
start/stop recording
Tabla de contenidos
Otros manuales de Cámara digital de edesix
