Edelbrock 5213 Manual de usuario

Rev. 3/08 - AJ/mc

Catalog #5213, #5214

Brochure #63-5213

Page 1 of 2

Edelbrock Anti-Hop Bars

for 1964-1972 GM A-Body (Catalog #5213)

& 1978-1987 GM A/G Body (Catalog #5214)

INSTALLATION INSTRUCTIONS

Please study these instructions carefully before installing your new anti-hop bars. If you have any questions, contact our

Technical Hotline at: 1-800-416-8628, 7 am to 5 pm, Monday-Friday, Pacific Standard Time or e-mail us at

[email protected].

Tools and Supplies Required:

❑ Jackstands ❑Torque Wrench (70 lb. min.)

❑Tire Chocks ❑Drill Motor

❑1/4” Drill Bit ❑Grease Gun

❑Floor Jack ❑Thread Lock Compound

❑7/16” & 3/4” Sockets and Wrenches

Caution: Installation requires being under raised vehicle. Support vehicle on level and stable ground using proper load

rated stands.

Note: Differential fill plug will not be accessible after installation. Check/change differential fluid before installation. The

right anti-hop will have to be removed to check fluid. After install, a fill plug style rear cover could be added.

1. Place vehicle on level stable ground (i.e. concrete or driveway). Chock front wheels at front and rear of tire

(Fig.1).

2. Raise rear of vehicle and support so to keep rear suspension loaded with vehicle weight. Removing rear tires is not

required but can be helpful.

3. During installation it is critical to maintain pinion angle. To do this, use floor jack to support pinion area of rear end

housing. NOTE: An angle finder can be used to measure pinion angle.

4. Remove left upper trailing arm bolt from rear end bushing and loosen front trailing arm bolt. Rotate trailing arm up

and out of way. On 1978-1987 A/G cars, remove brake line distribution block bolt.

5. Remove pressed-in O.E.M. rubber bushing with caution so as to not damage rear end housing.

6. Install left anti-hop bar with grease fitting facing rear of vehicle. (Left bar in #5213 will be stamped with #25-4027

and #5214 will be stamped with #25-4038). Minor moving of brake line may be required on some years and models.

On #5214 use 5/16” bolt, nut and bracket to relocate line

(Fig. 2).

IMPORTANT NOTE:

Proper installation is the responsibility of the installer. Improper installation will void warranty and may

result in poor performance and engine or vehicle damage.

INSTALLATION INSTRUCTIONS

Fig. 1 Fig. 2

Rev. 3/08 - AJ/mc

Catalog #5213, #5214

Brochure #63-5213

Page 2 of 2

Edelbrock Corporation, 2700 California St., Torrance, CA 90503

Tech Line: 1-800-416-8628

E-Mail: [email protected]

7. Locate anti-hop bar on steel bushing and 1/2"

(Fig. 3)

snug at this time.

8. Install upper trailing arm on anti-hop bar urethane bushing.

9. Drill 1/4" hole through axle housing web using anti-hop bar as guide. NOTE: Make sure to have at minimum 1/4" of

material between bolt hole and web edge,

(Fig. 2).

10. Install 1/4" bolt, washer and nyloc nut. Tighten bolt to 20 ft/lbs.

11. Use thread lock compound on upper trailing arm and steel bushing bolts and torque to 70 ft/lbs.

12. Remove right upper trailing arm bolt from rear end bushing and loosen front trailing arm bolt. Rotate trailing arm up

and out of way.

13. Remove pressed in O.E.M. rubber bushing with caution so as to not damage rear end housing.

14. Install right anti-hop bar with grease fitting facing rear of vehicle. (Right bar in #5213 is marked #25-4028, #5214 is

marked #25-4039).

15. Locate anti-hop bar on steel bushing and 1/2 bolt

(Fig. 3)

, snug at this

time.

16. Install upper trailing arm on anti-hop bar urethane bushing.

17. Drill 1/4" hole through axle housing web using anti-hop bar as guide.

NOTE: Make sure to have minimum of 1/4" of material between bolt hole

and web edge.

18. Install 1/4" bolt, washer and nyloc nut torque to 10 ft/lbs.

19. Use thread lock compound on upper trailing arm and steel bushing bolts

and torque to 70 ft/lbs.

20. Although Edelbrock anti-hop bar bushings are prelubed, you may want to lub the bushings. Install zerk fitting covers

to prevent dirt and corrosion of the zerk fittings.

Check hardware tightness after 10 miles and on a regular basis.

Note: To further upgrade your suspension, use other Edelbrock suspension, springs and shocks. See an Edelbrock

dealer or go to our website at www.edelbrock.com.

Fig. 3

Steel Bushing

and Bolt

Grind here,

if needed.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Pieza de automóvil de Edelbrock

Edelbrock

Edelbrock 67112 Manual de usuario

Edelbrock

Edelbrock 5658 Manual de usuario

Edelbrock

Edelbrock 5683 Manual de usuario

Edelbrock

Edelbrock 6719 Manual de usuario

Edelbrock

Edelbrock 73802 Manual de usuario

Edelbrock

Edelbrock 7892 Manual de usuario

Edelbrock

Edelbrock 1799 Manual de usuario

Edelbrock

Edelbrock 68642 Manual de usuario

Edelbrock

Edelbrock Pro-Flo 3 Manual de usuario

Edelbrock

Edelbrock 70024 Manual de usuario

Edelbrock

Edelbrock 5674 Manual de usuario

Edelbrock

Edelbrock 63-0144 Manual de usuario

Edelbrock

Edelbrock Performer RPM 1967 Manual de usuario

Edelbrock

Edelbrock 8147 Manual del propietario

Edelbrock

Edelbrock Fe Ford 5771 Manual de usuario

Edelbrock

Edelbrock Performer RPM Series Manual de usuario

Edelbrock

Edelbrock 2760 Manual de usuario

Edelbrock

Edelbrock 1795 Manual de usuario

Edelbrock

Edelbrock 5713 Manual de usuario

Edelbrock

Edelbrock 5694 (Stainless Steel) Manual de usuario

Edelbrock

Edelbrock 70028 Manual de usuario

Edelbrock

Edelbrock 770769 Manual de usuario

Edelbrock

Edelbrock 6669 Manual de usuario

Edelbrock

Edelbrock 4462 Manual

Manuales populares de Pieza de automóvil de otras marcas

Dakota Digital

Dakota Digital 650277 Manual de usuario

bosal

bosal 037031 Manual de usuario

Vintage Air

Vintage Air 571063 Manual de usuario

GFB

GFB EX38 Manual de usuario

bosal

bosal 028091 Manual de usuario

Dodge

Dodge 8W-43 Guía de inicio rápido

ICI

ICI Magnum FBM10DGN Manual de usuario

Volant Perfomance

Volant Perfomance 19435 Manual de usuario

BENDIX

BENDIX GEN 4 GEN 5 ABS Manual de usuario

Vintage Air

Vintage Air 571065 Manual de usuario

Rugged Ridge

Rugged Ridge 11503.13 Manual de usuario

BENDIX

BENDIX CYCLONE DURADRAIN TRAILER WATER Manual de usuario

Porsche

Porsche 968 - ASSEMBLY INSPECTION PROCEDURE AND MAINTENANCE... Guía

Sumitomo

Sumitomo FINE CYCLO FC-A 15 G Manual de usuario

Toshiba

Toshiba 48-1250 A Manual de usuario

aldes

aldes EHT2 Manual de usuario

Go Rhino

Go Rhino 24371T Manual de usuario

BBK

BBK 18950 Manual de usuario