ECOWITT GW1000 Manual de usuario
1
Wi-Fi Gateway with Temperature, Humidity
and Barometric Sensor
Operation manual
Model: GW1000
Thank you for purchasing this Wi-Fi Gateway with
built-in temperature, humidity and barometric pressure
sensor. Your sensor data will be available on your local
Wi-Fi network and the Internet. Supported sensors (sold
separately) include: outdoor temperature and humidity,
multi-channel temperature and humidity, rain, wind, soil
moisture, particulate matter (PM2.5). In the future
additional sensors will be supported, such as: water
leakage sensor, lightning detector, etc.
To ensure the best product performance, please read this
manual and retain it for future reference.
2
Contents
1 Unpacking ................................................................... 3
2 Overview..................................................................... 4
2.1 Features ............................................................ 4
3 Setup Guide................................................................. 6
3.1 Gateway Introduction....................................... 6
3.1.1 LED Indicators ...................................... 7
3.1.2 Button Function..................................... 8
3.2 Publish to Internet Weather Services................ 9
3.3 Gateway Wi-Fi Configuration ........................ 10
3.4 Adding weather services................................. 13
3.5 Ecowitt Weather.............................................. 16
3.6 Weather Underground..................................... 17
3.6.1 WU Dashboard vs Live Data............... 18
3.7 Calibration or Rain totals................................ 19
3.8 Registering with and using wunderground.com
.............................................................................. 20
3.9 Device Settings............................................... 22
3.10 Sensor ID...................................................... 23
3.11 Viewing data on wunderground.com............ 23
4 Specification.............................................................. 27
5 Warranty Information ................................................ 28
3
1Unpacking
Open your Wi-Fi gateway box and inspect that the
contents are intact (nothing broken) and complete
(nothing missing). Inside you should find the following:
QTY
Item Description
1
GW1000 Wi-Fi gateway
1
Cable clip
1
User Manual
Table 1: Package Content
If components are missing from the package, or broken,
please contact customer service to resolve the issue.
Note: The gateway must be plugged into a USB (2.0 or
later) port for its power supply. You may want to
use a USB extension cable (USB type A - Male
straight to female straight; not included) to allow
for better placement.
4
2Overview
Figure 1: Wi-Fi Gateway
2.1 Features
•Built-in temperature, humidity and atmospheric
pressure sensors (cabled probe attached to unit).
•Receives sensor data from external sensors, if
installed and configured (sold separately): outdoor
temperature and humidity, multi-channel (max 8)
temperature and humidity, rain, wind, soil moisture
(max 8), PM2.5 (max 4) and so on.
•Makes all sensor data available to mobile application
(WS View for iOS or Android) on your local
network.
•Mobile application is also used for local viewing of
sensor data, and to assist in configuration of
services.
•Pushes sensor data to Internet based weather
services.
5
•Supports uploading all the sensors data to Ecowitt
Weather server: https://www.ecowitt.net.
•Other supported weather services for uploading:
wunderground.com, Weathercloud, and WOW. Only
sensor data supported by each specific service will
be uploaded.
•View historical records from your WU station
(temperature, humidity, wind, rain).
•View all the sensor current and history records,
graph on Ecowitt Weather server. History records
can also be exported from the server.
•The gateway is powered by USB connection.
•Supports MAX 8 WH31 multi-channel temperature
and humidity sensor (optional)
•Supports MAX 8 WH51 soil moisture sensor
(optional) and MAX 4 WH41 PM2.5 air quality
sensor (optional)
6
3Setup Guide
3.1 Gateway Introduction
See Figure 2 to help you identify elements of the gateway.
Figure 2: Gateway Introduction
1 Wi-Fi Configure/Reset Button
2. RF Status Indicator Light
3. Wi-Fi Status Indicator Light
4. USB Connector for system power supply
5. Temperature, humidity and barometric 3-in-1 sensor
Figure 3:Gateway parts identification
7
Before configuring the gateway with your mobile
application, please read the description of the LED
indicators (2 and 3), and button function for better
understanding.
3.1.1 LED Indicators
RF (Blue): Indicates RF data receiving status
•Flash (each): indicates one packet of RF data from a
sensor was received.
•Off (steady): indicates no RF data received.
Wi-Fi (Red): Indicates Wi-Fi connection status
•On (steady): indicates connected to Wi-Fi network;
network communication normal and data uploaded
to configured weather service(s) successfully.
•Off (steady): Wi-Fi connection failed.
•Flash (slow - 1Hz), indicates connected to Wi-Fi
network; network communication normal, but
upload to one or more configured weather services
failed. First confirm Internet access through your
router is functioning, and then check whether the
upload server account and password are correct (use
WS View application).
•Flash (faster - 2Hz), indicates that Wi-Fi
configuration mode is active. Use the WS View
mobile application to complete the configuration.
8
3.1.2 Button Function
The black button is used for the following two modes:
Wi-Fi Configure Mode: Press and hold the button for
about 5 seconds until the Wi-Fi status LED is fast flashing
indicating the gateway is ready for Wi-Fi configuration.
Reset Mode: Press and hold the button for about 10
seconds will reset the gateway and clear the history data.
Note:
1. When powered up, and when there is no valid Wi-Fi
configuration (including very first time), the Wi-Fi
status LED will be fast flashing. It means that the
gateway is in the Wi-Fi configuration mode. Use the
mobile application to complete the configuration
process.
2. If you purchased optional sensor(s), you can power up
the new sensor at any time and use mobile
application’s live data view to confirm whether the
sensor has been added successfully.
3. To add multi-channels sensors WH51 or
WH41(optional), GW1000 firmware V1.4.6 or above
will be required. No specific channel sensor needed
to purchase, for each new sensor will be recognized
as a new channel according to the Power-on
sequence on the app.
Please follow the operation tips:
1. Go to your app store and download the latest WS
View app and install it.
9
2. Open the app and update the firmware to
V1.4.6(or above) as instructed on the app.
3. After the update, power on your first WH51 or
WH41 sensor and wait for several minutes.
4. Open the Live data page and check whether the
sensor is added as CH1.
5. If succeeded, you can power on other sensors one
by one and please attach a label on each sensors for
distinction.
3.2 Publish to Internet Weather Services
Your gateway can send your sensor data to WS View APP
via local network or selected internet-based weather
services. The supported services are shown in the table
below:
Service
Description
Ecowitt
Weather
Site: https://www.ecowitt.net
Ecowitt’ s new weather server that can
host a bunch of sensors that other
services don’t support at this time.
Weather
Underground
Site: https://wunderground.com
provides local & long-range weather
forecasts, weather reports, maps &
tropical weather conditions for
locations worldwide.
10
WOW
Site: https://wow.metoffice.gov.uk
A UK based weather observation
website.
Weather
Cloud
Site: https://weathercloud.net
A large network of weather stations
reporting data in real time from all
over the world.
Table 2: Supported weather services
3.3 Gateway Wi-Fi Configuration
The gateway can function as an independent Wi-Fi access
point during Wi-Fi configuration. This will be used to
allow your mobile application to connect to it directly
during configuration (temporarily), passing configuration
information about your normal Wi-Fi network to the
Gateway so that it can later connect to your preferred
Wi-Fi network.
Please follow the following procedure:
1. Download the mobile application from the iOS App
Store or Google Play store, as appropriate for your
device.
2. Plug your gateway into an available USB port that
supplies power and ensure it is in Wi-Fi
configuration mode (RED LED flashing fast). If it is
not, follow the procedure to put it in that mode (hold
down button for about 5 seconds).
Otros manuales para GW1000
2
Tabla de contenidos
Otros manuales de Puerta de ECOWITT
Manuales populares de Puerta de otras marcas
LST
LST M500RFE-AS Manual de usuario
Kinnex
Kinnex Media Gateway Manual de usuario
2N Telekomunikace
2N Telekomunikace 2N StarGate Manual de usuario
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario
Telsey
Telsey CPVA 500 - SIP Manual de usuario
