Ecler VEO-XRI1C Manual de usuario
VEO-XTI1C / VEO-XRI1C
VEO-XTI2L / VEO-XRI2L
How to configure a Cisco SG300 Ethernet Switch for Ecler
VEO over IP products
QUICK START GUIDE
2
INDEX
1. Establishing communication with the Cisco Ethernet Switch.......................................3
2. Enabling IGMP Protocol ........................................................................................................3
3. Enabling Jumbo Frame...........................................................................................................7
4. Configuring the DHCP Server.............................................................................................. 7
3
1. Establishing communication with the Cisco Ethernet Switch
1. Connect your computer to the Cisco Ethernet Switch using an Ethernet
cable. The Cisco SG300 Ethernet Switch comes with a default Static IP
address of 192.168.1.254; you must configure your PC with a Static IP
address in the same subnet.
2. Set a Static IP address on your computer network interface card, such as
192.168.1.66 along with the following mask 255.255.255.0.
3. Open your Internet browser and digit the default IP address of the switch:
http://192.168.1.254. The Default User ID and Password for the unit is
“Cisco”.
2. Enabling IGMP Protocol
The IGMP Protocol is mandatory for the correct operation of the VEO over IP
products in multicast configurations. Without IGMP the audio/video can’t work
properly or may freeze.
1. Select Multicast →Properties. Enable the Bridge Multicast Filtering Status
by activating the related selection box and clicking on Apply.
4
2. Select Multicast →IGMP Snooping. Enable the IGMP Snooping Status by
activating the related selection box and clicking on Apply.
3. In the IGMP Snooping Table, select the default VLAN ID 1 and click on Edit.
5
4. In the resulting window, activate the related selection box for IGMP
Snooping Status and verify that the Immediate Leave selection box is
enabled and then click on Apply.
5. Select Administration →File Management →Copy/Save Configuration.
Enable Running Configuration and Startup Configuration as shown below
and save all changes by clicking Apply.
6
6. Select Administration →File Management →Reboot, and click on the
Reboot button to reboot the Ethernet switch and make all the changes
running.
7
3. Enabling Jumbo Frame
1. Select Port Management →Port Settings. Enable Jumbo Frames by
activating the related selection box and click on Apply.
4. Configuring the DHCP Server
The DHCP Server will automatically configure the IP addresses of each device
connected to the switch. All the devices need to be set as DHCP client in their own
Network Configuration page. This allows avoiding any conflict between devices.
Note: Please check VEO user manual for IP configurations of each product,
accordingly to your installation needs.
8
1. To change the Ethernet Switch Static IP address to the same subnet as the
AV over IP Devices, select Administration →Management Interface →IPv4
Interface. Set IP Address Type to Static, and enter the IP Address
(accordingly to your network requirements), and set the Network Mask to
255.255.255.0. In this case we e default IP address. After applying these
settings you need to change the IP address on your computer network
interface card to the same subnet just set above.
2. Select IP Configuration →DHCP Server →Network Pools and click on the
Add… button
9
3. Set the Pool Name, the Network Mask (255.255.255.0), the Address Pool
Start (192.168.1.10), and the Address Pool End (192.168.1.100). Verify
that you allocate enough IP addresses for all Transmitters and Receivers
present on the network.
Click on the Apply button.
10
4. Select IP Configuration →IPv4 Management and Interfaces →DHCP
Server →Properties.
Enable the DHCP Server Status by activating the related selection box and
clicking on Apply.
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Extensor de Ecler
Ecler
Ecler VEO-XPS43 Manual de usuario
Ecler
Ecler VEO-XTI1C Manual de usuario
Ecler
Ecler VEO-XPT24 Manual de usuario
Ecler
Ecler VEO-XTI1CG2 Manual de usuario
Ecler
Ecler VEO-XTI2L Manual de usuario
Ecler
Ecler VEO-XPS15 Manual de usuario
Ecler
Ecler VEO-XPT44 Manual de usuario
Ecler
Ecler VEO-XTI2L Manual de uso y mantenimiento
Ecler
Ecler VEO-XPT44A Manual de usuario
Ecler
Ecler VEO-XTT44 Manual de usuario
