Eaton 10250T Manual

Effective June 2011

Instructional Leaet IL04707001E

10250T contact block assembly

• Underwriters Laboratories Listed

• For use on a flat surface of Type 1, 2, 3, 3R,

3S , 4, 4X, 12, and 13 enclosures

• IP65

 For indicating lights without moveable operations.

General

1. Drill mounting hole for vertical or horizontal

mounting per one of the figures above.

2. Ensure sealing gasket is in place on the

operator. Align locating nib of operator

with notch in panel and insert operator

through mounting hole. Exception: See

special instruction publication 20437 for

placement of sealing gasket when using

10250T/91000T protective boots.

3. Place legend plate and mounting nut over

operator. Tighten mounting nut. If applicable,

assemble lenses, mushroom buttons, etc., to

operator. Tighten securely (5 ft-lbs) (6.8 Nm).

4. Torque terminals to 7 in-lbs (0.8 Nm).

For ease of assembly, Eaton recommends

the following tools:

• 10250T/91000TA95 for 10250T/91000T octagonal

nuts, E29, and E30 lines

• E22CW for 10250T/91000T octagonal nuts,

E22, E34, and E30 lines

Retaining

Nut

Thrust Washer

(Optional)

Nameplate

Operator

Gasket

Panel

0.063–0.250

(1.6–6.3 mm)

Assemble MasterTest or

Flasher Modules to Rear

of Contact Blocks.

Wires Shown are not Included

Ratings are Stamped

on Light Unit

and Contact Block

#755 Lamp

Saddle ClampType Terminals

14 AWG–22 AWG

(2.5 mm2—0.34 mm2)

Solid or Stranded.

Do Not Mix One or Two

Conductors perTerminal

Earth/Ground

Conductor

91000/E34

EarthTerminal

ILL

P.B.

IND

LIGHT

PUSH

PULL

T-Line Operator

Lens Washer

0.60

(15.2 mm)

1.20

(30.5 mm)

0.136 (3.5 mm) Diameter Hole or

0.180 (4.6 mm) Rectangular Notch

Use 60/75ºC Copper Conductors Only

Vertical Mounting Horizontal Mounting

Eaton Corporation

Electrical Sector

1111 Superior Ave.

Cleveland, OH 44114

United States

877-ETN-CARE (877-386-2273)

Eaton.com

Printed in USA

Publication No. IL04707001E / Z11206

June 2011

Eaton is a registered trademark

of Eaton Corporation.

All other trademarks are property

of their respective owners.

Instructional Leaet IL04707001E

Effective June 2011

10250T contact block assembly

Push–pull operators

Application guide

To assist in the selection of contact blocks, the diagram on page 1

shows pictorially by symbols “A” and “B” locations of contact

circuits after assembly of contact blocks to the operator. Table 1 and

Table 2 show the effect of the push and pull operations on either

NO or NC contacts.

A maximum of two contact blocks may be used with each operator.

Maximum torque of stacking screws is 9 in-lbs. Adding more

than two blocks may cause this switch to malfunction. Single

circuit contact must be mounted under circuit “A”. Special function

contact blocks are not available for use with the three-position

push–pull operator.

ote:N Buttons and lenses in various colors are ordered and packaged sepa-

rately. This pushbutton unit is oiltight when the adapter gasket and button or

lens gasket are securely tightened.

Table 1. Push–Pull Operator Types

Operator

Type

Contact

Block

Circuit

Operator Mode and Contact Circuit

Pulled Intermediate Pushed

Circuits

A B Circuits

A B

Momentary

push and pull

and

momentary pull,

maintained push

2NC

1NO

X X

O X

O O

Maintained

push and pull

(Two-positions)

1NC

2NC

1NO

2NO

X or X

X X

O or O

O O

intermediate

position

O or O

O O

X X

Momentary

push and pull

(Three-positions)

1NO–1NC O X O O X O

ote:N X = contacts closed; O = contacts open

Table 2. Push–Pull Wire Position Operation

Control Line Diagram Operator Circuits Operator Mode

Three-wire,

three-position,

momentary

Circuit

L2L1

Momentary

push and pull

2NC

contact

blocks

START

(Momentary)

Normal position

(Maintained)

STOP

(Momentary)

Two-wire,

two-position,

maintained

Circuit

L2L1

Maintained

push and pull

1NC

contact

blocks

START

(Maintained)

intermediate

position

STOP

(Maintained)

Three-wire

momentary pull,

maintained push

Circuit

L2L1

Maintained

push and

maintained

ready,

momentary

pull to start

2NC

contact

blocks

START

(Momentary)

Normal position

(Maintained)

STOP

(Momentary)

Otros manuales de Cambiar de Eaton

Eaton

Eaton Cooper Power NR Series Especificaciones técnicas

Eaton

Eaton KA349WE Manual de usuario

Eaton

Eaton FAK-R/V/KC01/IY Manual de usuario

Eaton

Eaton P5-125/Z Manual

Eaton

Eaton TRIPP LITE U460-003-3AG Manual de usuario

Eaton

Eaton Cutler-Hammer ATVSKDA30300XSU Manual de usuario

Eaton

Eaton PV-20A-2P-AC-I1/SVB-SW Manual

Eaton

Eaton P5-125/Z Manual

Eaton

Eaton xiria series Manual de usuario

Eaton

Eaton Pow-R-Line SPX0361126 Manual de usuario

Eaton

Eaton Cutler-Hammer ATC-300 Manual de usuario

Eaton

Eaton DILM185A Manual de usuario

Eaton

Eaton AT0 I Series Manual

Eaton

Eaton XNH1-1-A Series Manual

Eaton

Eaton PDI WaveStar BCMS Manual de usuario

Eaton

Eaton ASALMSN Guía del usuario

Eaton

Eaton TM-1-8290/E/SVB Manual

Eaton

Eaton Cutler-Hammer NTV Series Manual de capacitación

Eaton

Eaton Powerware 9155 Manual de usuario

Eaton

Eaton ATR Series Manual

Eaton

Eaton Cutler-Hammer Manual de programación

Eaton

Eaton 9155 UPS Manual de usuario

Eaton

Eaton Crouse-hinds series Manual de usuario

Eaton

Eaton xComfort CTAA-01/01 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario