Eaton S801T Manual de instrucciones

Instructions for Installing Lugs or Bus Interface Kits onto Soft Starter,

Models S801T/S811T, S801U/S811U, and S801V/S811V

The typical kit includes three lugs or bus interfaces with hardware for line or load side mounting on the S801T,

S801U,S801V, S811T, S811U or S811V frame. There are two screw lengths included with the typical kit. The inch

screws are used for line side mounting. The 3 inch screws are used for load side mounting.

The EML40, universal lug kit, includes separate bus interface components and hardware. 1.75 inch screws are used

for line side mounting. .75 inch screws are used for load side mounting.

Effective 05/06

* Requires special lug cover. Check with EATON | Cutler-Hammer for availability.

Pub 9000

Revision 01

TO AVOID SHOCK HAZARD,

DISCONNECT ALL POWER

BEFORE ANY FUNCTIONS

ARE PERFORMED ON THIS

EQUIPMENT.

AVERTISSEMENT

WARNING

Hazard of Burn or

Electrical Shock

Risque de Brulure ou de

Choc Electrique

POUR EVITER TOUT CHOC

ELECTRIQUE, COUPLER

LALIMENTA-TION DE CET

EQUIPEMENT AVANT DY

EFFECTUER DES TRAVAUX.

POWER WIRING

00mm

S801T/

S811T

S801U/

S811U

EML

EML 3

EML 4

EML 5

EML 6

EML50

Frame

Size Cat. No. Number of

Conductors

Wire Sizes

75°C only

Torque

Requirements

Number of

Kits Reqd

1.75 BUS

4-1/0 ( 1. -53.5mm²)

4/0 - 500 MCM (107- 40mm²)

4/0 - 500 MCM (107-150mm²)

/0 - 300 MCM (70-150mm²)

N/A

8,3 N-m ( 50 LB-IN)

5,5 N-m ( 5 LB-IN)

N/A

90mm

S801V/

S811V

EML 8

EML30

EML3

EML33

EML40

EML51A

EML51B

.00 BUS

3.00 BUS

4/0 - 500 MCM (107- 40mm²)

/0 - 300 MCM (70-150mm²)

4/0 - 500 MCM (107- 40mm²)

N/A

8,3 N-m ( 50 LB-IN)

5,5 N-m ( 5 LB-IN)

34,0 N-m (300 LB-IN)

N/A

Fig. 1 S801V Shown with Lugs Installed on Load Side

Without Terminal Cover in Place

FOR S801V/S811V

1. Remove soft starter terminal cover by removing the four #6 cover screws. Once screws have been removed, slide

cover off soft starter.

. Line Side - Fasten lugs to soft starter with three each 2 inch long allen head cap screws, 1/4 lock washers, and

1/4 flat washers per pole. Tighten to 1 0 LB-IN (13.6 N-m). For the EML40, attach lugs and tighten 1.75 inch screws

to 300 LB-IN. Discard remaining hardware.

Load Side - Remove shipping bolts. Position and fasten lugs to soft starter with three each 3 inch long allen head

cap screws, 1/4 lock washers, and 1/4 flat washers per pole. Tighten to 1 0 LB-IN (13.6 N-m). For the EML40,

attach lugs and tighten .75 inch screws to 300 LB-IN. Discard remaining hardware.

3. Replace terminal cover. Tighten the four #6 cover screws to 5 LB-IN (0.6 N-m). NOTE: The cover cannot be used

with the EML40 kit.

4. When the EML40 Kit is used, verify that 1/ inch clearance is maintained between the poles.

FOR S801T/S811T, and S801U/S811U

1. Remove soft starter terminal cover by removing the two #6 cover screws. Once screws have been removed, slide

cover off soft starter.

. Line Side - Fasten lugs to soft starter with one each 2 inch long allen head cap screw, 1/4 lock washer, and 1/4

flat washer per pole. Tighten to 1 0 LB-IN (13.6 N-m). Discard remaining hardware.

Load Side - Remove shipping bolts. Position and fasten lugs to soft starter with one each 3 inch long allen head

cap screw, 1/4 lock washer, and 1/4 flat washer per pole. Tighten to 1 0 LB-IN (13.6 N-m). Discard remaining

hardware.

3. Replace terminal cover. Tighten the two #6 cover screws to 5 LB-IN (0.6 N-m).

Pub 9000

Page

Effective 05/06 IT SS#10680

Milwaukee, WI U.S.A.

DISCONNECT ALL POWER BEFORE PERFORMING ANY WORK!

Fig. S801V Shown with EML40 Lugs Installed on

Load Side - Terminal Cover Cannot be used with

EML40 Kit.

1/2 MIN.

CLEARANCE

Este manual sirve para los siguientes modelos

Otros manuales de Electricidad industrial de Eaton

Eaton

Eaton DMM-125/I5 Series Manual

Eaton

Eaton Power Defense PDG-3 Series Manual

Eaton

Eaton Power Xpert PXR 10 Manual de usuario

Eaton

Eaton QM40 Series Manual

Eaton

Eaton DILM7-21 Manual

Eaton

Eaton HALO E7 ICAT New Construction Series Manual de usuario

Eaton

Eaton MEMSHIELD 4 Manual de usuario

Eaton

Eaton CHFPCS Manual de usuario

Eaton

Eaton DILM65-XIP2X Manual de usuario

Eaton

Eaton MSFB Series Manual

Eaton

Eaton Memshield 3 Series Manual

Eaton

Eaton COOPER POWER SERIES Manual de instrucciones

Eaton

Eaton RMQ-Titan C22 Series Manual

Eaton

Eaton Crouse-hinds series Manual de usuario

Eaton

Eaton Neo-Ray Define S122-125 DP Manual de usuario

Eaton

Eaton NZM-XDMI-DPV1 Manual

Eaton

Eaton easyE4 series Manual de usuario

Eaton

Eaton DualGuard-S ESF30 Manual de servicio

Eaton

Eaton CEAG SOU CG-S 2 x 4A Manual de servicio

Eaton

Eaton Series NRX Manual de usuario

Eaton

Eaton M22 ADC Series Manual

Eaton

Eaton NZM1-XTV 60 Series Manual

Eaton

Eaton LPC25 Manual

Eaton

Eaton RMQ-Titan M22-FI Series Manual

Manuales populares de Electricidad industrial de otras marcas

Rexroth Indramat

Rexroth Indramat DURADRIVE SYSTEM200 Manual técnico

Abtech

Abtech HVJB Series Guía

Murata

Murata GRM0335C1H8R1DA01 Series Manual de usuario

SAF-HOLLAND

SAF-HOLLAND CBX 5415.5 Manual de usuario

Newlong

Newlong NP-7H Manual de usuario

Murata

Murata GJM0335C1E4R4BB01 Series Manual de usuario

Stahl

Stahl 8575/12 Manual de usuario

SI Pegasus Manual de usuario

Murata

Murata GRM1555C1H2R7CA01 Seies Manual de usuario

Murata

Murata GRM0225C1E6R4BA03 Series Manual de usuario

Cooper Power Systems

Cooper Power Systems VXE15 Manual de usuario

S&C

S&C Vista SD Manual de usuario

Murata

Murata GRM0335C2A7R3CA01 Series Manual de usuario

Siemens

Siemens 3VA9988-0BM10 Manual de usuario

Siemens

Siemens SITRANS LVS100 Manual de usuario

Murata

Murata GRM32ER60G227ME05 Series Manual de usuario

Siemens

Siemens SENTRON SUPERSWITCH 3KL82 Series Manual de usuario

Rockwell Automation

Rockwell Automation Allen-Bradley MP-Series Manual de usuario