Eaton EG2-NA Manual de usuario

EG2-NA

Ethernet Gateway

Installation guide

Eaton Lighting Systems

Eaton Lighting Systems EG2-NA 9850-000225-02 2

Please Read This First

The EG2-NA is built and tested to strict safety regulations. By following the steps listed

below and elsewhere within this guide, you can ensure safe installation and operation of

these controller units.

• The EG2-NA must be installed only by a qualiﬁed electrician.

• The installation must comply with the appropriate electrical codes and regulations in

force in your area.

• The EG2-NA is designed for indoor installation and use only.

• Ensure that all wiring used conforms fully to local speciﬁcations and is sufﬁciently

rated for the installation.

• All new wiring must be fully veriﬁed before applying power.

• The high voltage supply should be fed to the EG2-NA via an external isolation breaker

with sufﬁcient capacity for the planned installation.

• Ensure that the supply is fully isolated at an external breaker before removing

the chassis covers. Test that power has been removed before starting to handle

conductors.

• Ensure that high voltage and low voltage wiring remains separate.

Contents

Safety 2

Introduction 3

Dimensions 3

Speciﬁcation 3

Weight 3

Product Overview 4

Mounting 4

Supply Wiring 5

Control Wiring 5

Setup Instructions 6

Eaton Lighting Systems EG2-NA 9850-000225-02 3

Introduction

The Ethernet Gateway provides a connection

between an iLumin or iLight lighting control

network and an Ethernet Local Area Network,

either through an Ethernet switch or wireless

router.

The EG2-NA acts as a host for the iLumin or

iLight series of remote applications including

iOS (iPhone/iPod Touch/iPad & Android OS

devices). Coupling the EG2-NA to a Wi-Fi

network enables secure scene control,

visual feedback and modiﬁcation from your

hand held device. Once conﬁgured, the

EG2-NA automatically loads room and scene

information to the connected hand held

device.

In addition to its handheld device capability,

the EG2-NA houses internal webserver pages

that allow for basic scene control functions.

These internal pages are accessed through an

internet browser and are password protected

for security.

The EG2-NA also facilitates the commissioning

of the iLumin or iLight system, allowing our

factory trained technicians to use the EG2-NA

connection to conﬁgure the control system on

a LAN or Wi-Fi enabled PC or via the internet

rather than by connecting directly into the

iLumin or iLight network.

Weight

• Packed: 2.6 kg (5.7 lbs)

• Unpacked: 2.4 kg (5.3 lbs)

Dimensions

Specication

Unit requires: 120-240 VAC 50/60 Hz 0.45A 1Ø

Maximum

iCAN network connection

Ethernet connection: Fully transformer isolated

Ambient temperature range: 0°C to 40°C

(32°F to 104°F)

Humidity: 20% to 90% non-condensing

Conﬁguration and sequence memory

Field upgradable FLASH program memory

Internal +15 VDC, 2A power supply

Eaton Lighting Systems EG2-NA 9850-000225-02 4

Product Overview Mounting

Location and spacing

The EG2-NA should be installed in a dry

ventilated location, where ambient conditions

are maintained within the requirements of the

unit.

The unit has ventilation slots on its sides

to allow convection cooling and under no

circumstances should these be blocked.

Allow 50mm (2”) above and below the unit if

trunking with a depth greater than 50mm (2”)

is used.

Mounting Holes

The unit is provided with four 6mm (1/4in)

diameter ﬁxing holes for wall mounting.

The mounting holes can be accessed by

undoing the four screws on the front cover and

removing it.

1. Ethernet Connection

2. CAN ID Button

3. iCAN Network Connector with a green

(power) and yellow (network activity) LED

4. Main Supply Terminal Block

5. Power Supply

6. Reset Button

6.89” (175mm)

7.09” (180mm)

0.25" (6.35mm)

Mounting Holes

4-O.

Eaton Lighting Systems EG2-NA 9850-000225-02 5

Supply Wiring

Connecting the Supply

This unit requires a 120-240 VAC single phase

supply (live and neutral) with 0.45 A capability.

A terminal block is used to connect the

incoming feed to the internal power supply.

Control Wiring

iCAN Network

A removable 5 position terminal block is

provided for the connection of iCAN network

cables. If the EG2-NA is located in the middle

of the network, incoming and outgoing cables

will terminate within the same connector.

iCAN Connectors

Cable type:

Cooper LC or Belden 1502R or 1502P

Maximum cable length: 305m (1000’) *

Devices per segment: 100 (without bridge or

repeater)

* A maximum segment distance of 1000m (3200’) is possible

if an additional 12V power supply and bridge/repeater is used.

Wire Gauge for Supply Terminals

The live, neutral and earth ground power

connections are made to the terminal

block provided for main power connection.

Recommended cable size for live, neutral, and

earth is 26 AWG - 10 AWG.

Live (Gray)

Neutral (Blue)

Earth (Green/Yellow)

Live (Gray)

Neutral (Blue)

Earth (Green/Yellow)

Termination OFF

Termination ON

+12V

(Red)

CAN-H

(White)

SHIELD

(Gray)

CAN-L

(Blue)

(Black)

iCAN

Device

iCAN

Device

EG2-NA

The EG-2-NA

has in-built

network

termination.

If the

EG-2-NA is

at the end of

the network,

ensure the

CAN TERM

jumper is

ﬁtted in the

Termination

ON position.

iCAN devices are ‘daisy-chained’ on the

network. Spurs from the Network are not

permitted and will result in communications

problems. Devices on an iCAN network can

be wired in any order. Termination is required

at both ends of the network.

T - Indicates where a termination is required.

Eaton Lighting Systems EG2-NA 9850-000225-02 6

Setup Instructions

Ethernet Network

Connect the provided RJ45 (568B) jack to an

Ethernet Switch or Wireless Router.

Conguration

iCAN Device Number

The EG2-NA is supplied with a iCANnet Device

number with Segment number 255 and a node

number in the range 1-255. Both Segment and

Node number can be changed using iCANsoft.

Power Up

The EG2-NA takes approximately 60 seconds

to be ready for use once power is applied.

Wait for the Green CAN LED to ﬂash slowly.

The Green Power LED will double ﬂash

continuously while EG2-NA is on. If Ethernet is

connected the Link and Data LEDs will indicate

successful connection.

Setting the IP Address

The factory set IP Address can be changed

using iCANsoft software either through a direct

PC Node connection through the iCANnet or

directly into the Ethernet port of the EG2-NA.

PC Node Method

Connect a computer running iCANsoft to the

iCAN network using an iLight/iLumin PC Node.

Search the network and load the EG2-NA into

iCANsoft.

Open the EG2-NA device and select the

Ethernet tab. Type in the desired settings.

Select OK or Apply to downoad the changes

to the EG2-NA.

To restore settings back to default, select the

‘Restore Settings’ button. Select OK or Apply

to download the changes to the EG2-NA.

NOTE: The EG2-NA default settings are to

use a ﬁxed IP address of 192.168.0.100.

Any device used to communicate with

the EG2-NA will need to be located within

the 192.168.0.x subnet unless IP Address

settings are changed.

Factory Default IP Settings

• IP Address 192.168.0.100

• Mask 255.255.255.0

• Default Gateway 192.168.0.1

• DHCP Off

Ethernet Input

Eaton Lighting Systems EG2-NA 9850-000225-02 7

Ethernet Port Method

The EG2-NA is supplied from the factory

without DHCP enabled and with a factory

default IP address assigned. In order to

communicate to the EG2-NA using the

Ethernet port, the PC being used must be

conﬁgured on the same subnet as the default

IP address. For details of setting the IP

address of your computer consult information

online speciﬁc to your Operating System.

If the EG2-NA you are conﬁguring is at the

factory default settings, the following settings

are suggested when assigning a static IP

address to your computer:

Reset to Factory Defaults

Factory defaults may be reset by the following

procedure:

• Remove power from the board.

• Press the CAN ID button and reapply power.

Keep the button pressed until the CAN

LED ﬂashes then stays on. At this point the

Ethernet settings will have been restored to

defaults.

• After setting to factory defaults, the

IP address of the device will revert to

192.168.0.100

Once you have conﬁgured your PC’s IP

address, connect the EG2-NA directly to the

PC. It may be necessary to use a crossover

cable, however, most current computers are

able to connect directly to another Ethernet

device using a standard Ethernet cable.

iCANsoft will be used for the conﬁguration

process. Open iCANsoft, then select from

the Toolbar Tools>Options>Network. Select

the Ethernet Gateway option and change the

IP Address to 192.168.0.100. Ensure that the

‘Use Password’ check box is ticked and the

default password: Cooper123 is entered (case

sensitive).

Select OK to conﬁrm.

Search the network and load the EG2-NA into

iCANsoft. Follow the steps outlined in the PC

Node Method section to conﬁgure the desired

IP Address for the EG2-NA.

Once the IP Address settings have been

applied, initialize the new settings in the

EG2-NA device by pressing the reset button

next to the Ethernet conneciton or by

disconnecting and reapplying power.

Once conﬁguration is complete, if you will

be using iCANsoft through the ethernet

connection, you will need to update the IP

Address in the Toolbar Tools>Options>Network

section to match the settings you have

assigned to the unit. This screen will also

allow you to re-select the option for PC Node

to allow for direct PC Node access for this

database.

Factory Default IP Settings

• IP Address 192.168.0.99

• Subnet Mask 255.255.255.0

• Gateway 192.168.0.1

Document: EG2-NA 9850-000225-02

Eaton Lighting Systems

Usk House, Lakeside, Llantarnam Park,

Cwmbran, NP44 3HD. UK

T: +44 (0)1923 495495 F: +44 (0)1923 228796

E: [email protected] EatonLightingSystems.com

iLight Support

(International)

20 Greenhill Crescent,

Watford Business Park,

Watford, Herts,

WD18 8XG. UK

T: +44 (0)844 324 9100

(available Mon-Fri 9am-5pm GMT)

www.iLight.co.uk

Tec[email protected]

iLumin Support

(North America)

1121 Highway 74 South

Peachtree City, GA 30269

P: 770-486-4800

(Canada)

5925 McLaughlin Road

Mississauga, Ontario L5R 1B8

P: 905-501-3000

www.eaton.com/lighting

All products manufactured by Eaton Lighting Systems and identiﬁed with the iLight or iLumin

product series mark are warranted to be free from defects in material and workmanship and shall

conform to and perform in accordance with Seller’s written speciﬁcations.

This warranty will be limited to the repair or replacement, at Seller’s discretion, of any such goods

found to be defective, upon their authorized return to Seller. This limited warranty does not apply

if the goods have been damaged by accident, abuse, misuse, modiﬁcation or misapplication, by

damage during shipment or by improper service.

There are no warranties, which extend beyond the hereinabove-limited warranty,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE

IMPLIED WARRANTY OF FITNESS.

No employee, agent, dealer, or other person is authorised to give any warranties on behalf of the

Seller or to assume for the Seller any other liability in connection with any of its goods except in

writing and signed by the Seller. The Seller makes no representation that the goods comply with

any present or future federal, state or local regulation or ordinance. Compliance is the Buyer’s

responsibility.

The use of the Seller’s goods should be in accordance with the provision of the National Electrical

Code, UL and/or other industry or military standards that are pertinent to the particular end use.

Installation or use not in accordance with these codes and standards could be hazardous.

WARNING HAZARDOUS VOLTAGES

DISCONNECT FROM SUPPLY

BEFORE REMOVING COVERS

NO USER SERVICEABLE PARTS INSIDE

SERVICE BY QUALIFIED PERSONNEL ONLY

WARNING

To reduce the risk of ﬁre or electric shock,

DO NOT expose this device to rain or moisture.

DO NOT energise unless the front cover is in place.

This device must be earthed.

Installation, programming and maintenance must be carried out by qualiﬁed personnel.

Eaton Lighting Systems cannot accept responsibility for repairs or modiﬁcations that are not

competently executed and in accordance with service or upgrade information.

CE compliant to all relevant standards

Tabla de contenidos

Otros manuales de Puerta de Eaton

Eaton

Eaton Power Xpert Gateway 900 Manual de usuario

Eaton

Eaton EASY209-SE Manual

Eaton

Eaton Power Xpert Meter 2000 Manual de usuario

Eaton

Eaton EG2-NA Manual de usuario

Eaton

Eaton EU5C-SWD-EIP-MODTCP Manual de usuario

Eaton

Eaton SmartWire-DT EU5C-SWD-DP Manual de usuario

Eaton

Eaton PXG950-4G Manual de usuario

Eaton

Eaton PXG600E Guía

Eaton

Eaton EG-2 Manual de usuario

Eaton

Eaton INDGW-X2 Manual de usuario

Eaton

Eaton Power Xpert Meter 2000 Manual de usuario

Eaton

Eaton Power Xpert Gateway 200E Guía

Eaton

Eaton SWIRE-GW-MB Manual de usuario

Eaton

Eaton INDGW-M2 Manual de usuario

Eaton

Eaton Power Xpert Gateway Minislot Manual de programación

Eaton

Eaton SmartWire-DT Manual de usuario

Eaton

Eaton SmartWire-DT Manual de usuario

Eaton

Eaton EMP Manual de usuario

Eaton

Eaton 415U-2 Manual de usuario

Eaton

Eaton XNE-GWBR-2ETH-MB Manual de usuario

Eaton

Eaton Power Xpert Gateway 900 Manual de instrucciones

Eaton

Eaton LumenSafe Manual de usuario

Eaton

Eaton 415U-2 Manual de usuario

Eaton

Eaton Moeller SmartWire-Darwin Series Manual de usuario

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario