Eaton CGLine+ Touchscreen Controller Manual de usuario
CGLine+ Web Controller
Manual
Betriebsanleitung
Manuel
Target group: Skilled electricians
Zielgruppe: Elektrofachkraft
Public cible : Électriciens confirmés
CGLine+ Touchscreen Controller
English ................................... 3
Deutsch ............................... 29
Français ............................... 55
2Manual CGLine+ Touchscreen Controller ZNO2038000 A www.eaton.com
Start image – CGLine+ Controller Software
3Manual CGLine+ Touchscreen Controller ZNO2038000 A www.eaton.com
GB
1 Start image – CGLine+ Controller Software
The following background image is shown after the start-up process of the
CGLine+ Controller software:
IMPORTANT
If the settings of the touch panel need to be modi-
fied, tap on the lower edge to open the Windows
task bar.
All functions are presented in detail in the following sections. A summary of func-
tions is given here:
ote:N All operations are protected with a PIN number. Without typing in a PIN
number, the status can only be displayed.
Select the British flag to access the system settings, e.g. to modify the language
of operation.
The status of the CGLine+ Web Controller is shown on the left side. Tap on the
button under the status message to access the internal display levels of the
Controller.
The middle three display windows show the status (summary messages) of all
connected self-contained luminaires according to DIN VDE 0100-560 (Displays
560.6.14). These include:
•Operation = normal operation;
•battery operation, e.g. in case of power failure; and
•fault summary, e.g. a battery failure of a luminaire.
Click on the coloured area to access a detailed presentation of the messages.
PIN authentication for operation
4Manual CGLine+ Touchscreen Controller ZNO2038000 A www.eaton.com
GB
All connected self-contained luminaires can be blocked simultaneously on the
right side.
In the lower blue control area, it is possible to launch a function test of all lumi-
naires, to access the logbook and to make further settings.
Tap on the red Power button to close the software application if necessary.
2 PIN authentication for operation
For configuration control operations, e.g. to block luminaires, a prompt window is
shown with a virtual numeric keypad to type in a PIN number:
The Administrator PIN and User PIN are set ex
works. The Administrator has full access rights. The
User only has limited rights, e.g. to start a function
test. The rights required for performing an operation
are shown in the PIN prompt window.
Administrator
9876 followed by OK
User
0000 followed by OK
ote:N The PIN numbers of the
Administrator and User can be changed in the set-
tings. See next page.
Basic software settings
5Manual CGLine+ Touchscreen Controller ZNO2038000 A www.eaton.com
GB
3 Basic software settings
Tap on the British flag button to access the settings menu of the software.
Language:
Select one of the 19 languages of opera-
tion in the Language menu; the language
is modified without restarting the pro-
gramme.
General:
• Type in a project name of max.
80digits.
• Change the User and
Administrator PIN number.
IMPORTANT
Memorise the new PIN or write it
down.
• Change the background colour.
Further functions and display operations in the base window
6Manual CGLine+ Touchscreen Controller ZNO2038000 A www.eaton.com
GB CGLine+:
Select whether the blocking button
on the base window performs the
“Block” or “Rest mode” (for France
only) operation.
Maintained mode ON - the
CGLine+ luminaires can be turned
on/off if the L terminal on the
luminaire is bridged with the L line.
4 Further functions and display operations in the base window
Status display of the Controller
Click on the button to open the CGLine+ Web-Controller device window. See next
page.
The Block button is used to block all connected luminaires (PIN authentication)
to prevent a complete discharge, e.g. in case of a power failure during operation
downtimes.
Close the programme (PIN authentication).
Start FT
Click on the button to start a function test of all connected self-contained lumi-
naires.
(User/Admin PIN authentication)
Further functions and display operations in the base window
7Manual CGLine+ Touchscreen Controller ZNO2038000 A www.eaton.com
GB
Logbook
Click on the button to display the logbook for a period of at least 4 years with all
events in detail.
Configuration
Not in use for this Controller
Services
Click on this button to store and load the files and logbooks.
Click on the coloured status display to open a detailed status view in Explorer style.
See next page.
Device window – CGLine+ Web-Controller
8Manual CGLine+ Touchscreen Controller ZNO2038000 A www.eaton.com
GB
5 Device window – CGLine+ Web-Controller
Structure of the device window
2
2
Direct status messages for the device
with coloured status display:
green = OK, red = malfunction
Display of the active strand with the
total status of the luminaires in the
strand.
By clicking on the relevant strand from 1
to 4, you can change the display for the
strand to the status.
Group name and installation name (up to 20
digits each)
Field for additional information (up to 100
digits)
Buttons for Commandos or
configuration settings
Status display for
the relay outputs
and digital inputs
Click left mouse
button=
Information window
Click right mouse
button=
Open web server
via web browser
By clicking on the zone for a
strand you access the zone image
with the installed luminaires
directly
Display of active zones 2, 4, 5 or 8
for 4-strand operations in strand.
By clicking on the zone you access
the zone image with the luminaires
installed.
The number of active zones in the
strand can be set in the menu item
“Configuration”.
Alarm list with acknowledgement
option identical with main group
image
Installed strands, max. 4 units with
max. 100 CGLine luminaires each,
with display of current status:
•Green = luminaires in strand OK
•Yellow = min. 1 luminaire being
tested
•Red = min. 1 luminaire in strand
broken
•Grey field means “Strand not
installed”.
Device window – CGLine+ Web-Controller
9Manual CGLine+ Touchscreen Controller ZNO2038000 A www.eaton.com
Status display of the device
Operation Red = when at least one luminaire is not operationally ready, e.g. blocked
FT Yellow = when at least one luminaire is currently undergoing a function test (lumi
naire test)
OT Yellow = when at least one luminaire is currently undergoing an operating
time test (battery test)
Blocked Red = when at least one luminaire is currently blocked
Ethernet Red = when communication between the Controller and CGVision has been dis
rupted
Malfunction Red = when at least one luminaire has a malfunction, e.g. battery fault
Ext. monitor Red = malfunction with externally connected device
Admin logged in Green = signals that someone is logged in as administrator on the web server for
CGLine+ Web-Controller
Output 1/2 Red = relay outputs in accordance with active configuration
Input 1/2 Yellow = digital inputs in accordance with active configuration
Status displays for the CGLine+ Web Controller
GB
Device window – CGLine+ Web-Controller
10 Manual CGLine+ Touchscreen Controller ZNO2038000 A www.eaton.com
GB
Status display of the device
Selected strand: All status messages in this window apply to strand 1.
Function test Yellow = when at least one luminaire in the strand is currently undergoing a function test
Operating time test Yellow = when at least one luminaire is currently undergoing an operating time test
Delayed emergency
lighting Yellow = when at least one luminaire is still in delayed emergency lighting following a power
cut
Battery fault Red = when at least one luminaire has a battery fault
Luminaire malfunction Red = when at least one luminaire has an LED fault
Deferred operating time test Red = when at least one luminaire has a deferred operating time test, because less than 24
hours earlier there was a partial discharge
Battery operation Red = when at least one luminaire is battery operated
Communication Red = when at least one luminaire has a communication disruption with the Controller
Blocked Red = when at least one luminaire in the strand is blocked
Error in operating time test Red = when at least one luminaire has not passed the operating time test (battery test)
Function test error Red = when at least one luminaire has not passed the function test (luminaire test)
Deferred function test Red = when at least one luminaire has deferred the function test, because a partial discharge
took place earlier
Total zone status The configured zones and their total status are shown in the lower part of the window. In the
case of 4-strand operations this can be 2, 4, 5 or 8 zones and in the case of 2-strand opera-
tions 4, 8, 10 or 16 zones.
In CGLine compatibility mode only 1 zone is possible for each! By clicking on the correspond-
ing zone you access the zone image with the luminaires installed.
Status displays for the strand selected (red). Strand selection is made by clicking on
the strand number in the right strand status (blue).
Tabla de contenidos
Idiomas:
Otros manuales de Controladores de Eaton
Eaton
Eaton Vickers SMC20 Manual de usuario
Eaton
Eaton XC-152 Series Manual de usuario
Eaton
Eaton CDAE-01/04 Manual de usuario
Eaton
Eaton ATC-800 Manual de programación
Eaton
Eaton EMS 2,4 Series Manual de usuario
Eaton
Eaton AMPGARD Manual
Eaton
Eaton ELCM Series Manual de usuario
Eaton
Eaton Cutler-Hammer ELC Series Guía de instalación
Eaton
Eaton LMR PLUS Manual de usuario
Eaton
Eaton S611 Manual
Eaton
Eaton xComfort Bridge Manual de lista de piezas
Eaton
Eaton xComfort CSAU-01/01-10 Manual de usuario
Eaton
Eaton S801+ Series Manual de usuario
Eaton
Eaton EMS-SWD Series Manual de usuario
Eaton
Eaton MFD-Titan MFD-80 Series Manual
Eaton
Eaton DILE Series Manual de usuario
Eaton
Eaton Ampgard 400 Manual de usuario
Eaton
Eaton Greengate RC3 Manual de usuario
Eaton
Eaton ELC2 Series Manual de usuario
Eaton
Eaton Crouse-Hinds Flex-Station EDS Series Guía de configuración
