easyRAID S4-ESTT Manual de usuario
easyRAID S4-ESTT
eSATA (1.5Gb) to Serial ATA
Disk Array System
User Manual
Version 1.0
S4-ESTT
eSATA (1.5Gb) to serial ATA
Disk Array System
User Manual
Important Safety Instructions, Care and Handling
Before starting, take a few minutes to read this manual.
Read all of these instructions and save this manual for
later reference.
Protect the disk array system from extremely high or low
temperatures. Let the disk array system warm (or cool)
to room temperature before using it.
Protect the disk array system from being bumped or
dropped. Do not place the disk array system on an
unstable cart, stand, or table. It may fall, causing serious
damage to the product.
Keep the disk array system away from magnetic forces.
Do not use the disk array system near water.
Keep the disk array system away from dust, sand, or dirt.
Gaps and openings in the cabinet are provided for venti-
lation. Never block or cover these openings, because
the disk array system may overheat and become unreli-
able. Don’t place the disk array system on a bed, sofa,
rug, or other similar surface.
Do not place the disk array system near or over a radia-
tor or heat register.
Refer to the rating plate for the correct voltage and
ensure that the appliance voltage corresponds to the
supply voltage.
V
The appliance must be grounded. The disk array system
is equipped with a 3-wire grounded type of power cord.
This power cord will only fit into a grounded type of
power outlet.
If an extension cord or a power center is used with the
disk array system, make sure that the total current con-
sumption of all products plugged into the wall outlet
does not exceed the ampere rating.
Do not place the disk array system where the cord will
be walked on.
Never push any kind of object into the disk array system
through cabinet gaps and openings, since they may
touch dangerous voltage points and cause a risk of fire
or electric shock.
Unplug the power cord from the wall outlet before clean-
ing. Keep the disk array system dry. Do not use liquid
cleaners, aerosol cleaners, or a wet cloth. Use a damp
cloth for cleaning.
Except as specifically explained in this User Manual, do
not attempt to service the disk array system by yourself.
Opening or removing the covers may expose you to
dangerous voltages.
Unplug this product from the wall outlet and refer servic-
ing to qualified service personnel under the following
conditions.
• If the disk array system has been exposed to
water or any liquid.
• If the disk array system has been dropped or the
cabinet damaged.
User should not remove the cover.
Disconnect all power supply cords before servicing.
Preface
- 1 -
P
P
Pr
r
re
e
ef
f
fa
a
ac
c
ce
e
e
Notice
Product features and specifications described in this manual are subject to change
without notice.
The manufacturer shall not be liable for any damage, or for the loss of information
resulting from the performance or use of the information contained herein.
Trademarks
This manual has been checked for accuracy, but no guarantee is given that the contents
are correct. Information and specifications can change without notice.
Before starting any kind of hardware installation, please
ensure that all power switches have been turned off and all
power cords disconnected to prevent personal injury and
damage to the hardware.
User’s Manual
- 2 -
Regulatory information
For Europe
This equipment is in conformity with the EMC directive.
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules.
Those limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antennas.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circlet different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning:
A shielded-type power cord is required in order to meet FCC emission limits and
also to prevent interference to the nearby radio and television reception. It is
essential that only the supplied power cord be used.
Use only shielded cables to connect I/O devices to this equipment.
You are cautioned that changes or modifications not expressly approved by the
party responsible for compliance could void your authority to operate the
equipment.
Preface
- 3 -
UL Listed
This equipment meets UL's safety requirements.
User’s Manual
- 4 -
About this manual
Intended user
This manual is designed and written for users of the subsystem. This is an entry level
product suitable for most users.
Organization of the manual
This manual consists of the following sections:
Chapter 1: Introduction provides an overview of the as well as details of key features
and a list of specifications.
Chapter 2: Before you begin provides a detailed illustrated package list. This
chapter also contains all the information you need to decide whether to set
up a RAID 0, 0+1, 5 or RAID 5+spare array and lists important
pre-installation notices.
Chapter 3: Setting up the subsystem gives a detailed overview of the subsystem’s
features and guides you through the process of installing hard disk drives
into.
Chapter 4: Setting up an array explains how to set the RAID level, create an array
and connect to a host computer.
Chapter 5: Partitioning the array tells you how partition the array in Windows, Linux
or Mac OS X operating systems.
Appendix A: FAQ helps you deal with encountered problems in the form of Q&A.
Appendix B: Glossary defines relevant technical terms used in this manual.
Appendix C: LCD Display Messages lists all status and error messages that may be
displayed on built-in display.
Appendix D: Updating Firmware explains how to install new or updated firmware on.
Tabla de contenidos
Otros manuales de Sistema de matriz de discos de easyRAID
easyRAID
easyRAID ERQ12+U4R2 Instrucciones de uso
easyRAID
easyRAID Q16PS-F4R3 Instrucciones de uso
easyRAID
easyRAID S16-F2R4 Instrucciones de uso
easyRAID
easyRAID ERP12R-8FR2 Manual de usuario
easyRAID
easyRAID Q12-U4R2 Instrucciones de uso
easyRAID
easyRAID S8A2-PER2 Instrucciones de uso
easyRAID
easyRAID F8P U3R4 Manual de usuario
easyRAID
easyRAID Q12P2-F4R2 Instrucciones de uso
easyRAID
easyRAID X12P F2R4 Manual de usuario
easyRAID
easyRAID Q16Q-2GR3 Instrucciones de uso
easyRAID
easyRAID F8P U3TT Manual de usuario
easyRAID
easyRAID ERQ16-U4R3 Manual de usuario
easyRAID
easyRAID Q08QA-2GR2 Manual de usuario
easyRAID
easyRAID Q16QS-4GR3 Instrucciones de uso
easyRAID
easyRAID Q12PS-F4R2 Instrucciones de uso
easyRAID
easyRAID S8-U4TT Instrucciones de uso
easyRAID
easyRAID S8A2-PETT Instrucciones de uso
easyRAID
easyRAID Q12QS-4GR2 Instrucciones de uso
easyRAID
easyRAID Q16PS-S3R3 Instrucciones de uso
easyRAID
easyRAID X6P U3R2 Manual de usuario
Manuales populares de Sistema de matriz de discos de otras marcas
Fujitsu
Fujitsu ETERNUS DX60 S2 Manual de usuario
Accom
Accom WSD/2XTREME Manual de usuario
HP
HP Compaq Presario,Presario 4400 Instrucciones de uso
ATTO Technology
ATTO Technology Diamond Storage Array V-Class Manual de usuario
National Instruments
National Instruments RMX-8268 Manual de usuario
Overland Tandberg
Overland Tandberg SnapServer DX1 Manual de usuario
