Easee Equalizer Manual de usuario
Quick guide
Equalizer
3
Intended use This product is intended for optimizing the power
consumption by performing an automatic load
balancing between the Easee Charging Robot(s) and
the building. It avoids overload and power interruption
while charging the electric vehicle (EV).
The product needs to be paired with a Charging Robot
and connected to a compatible smart meter with the
cable provided. In order for the Equalizer to work, the
smart meter’s HAN port needs to be activated. The
product may only be operated with the approved
operating parameters and under the specified
environmental conditions (see pages 5 and 9).
Uses other than those specified here are not permitted.
4
Product overview
Wall mounting kit
(for non-metallic surfaces)
x1x1Cable
Equalizer (side view)
LED
Touch button Magnetic backside
5
Technical specifications
Product (mm): H: 110 x W: 110 x D: 27.5
Packaging (mm): H: 130 x W: 130 x D: 39
Operating temperature: -20 °C to +50 °C
Weight: 110 g
IP degree: IP40
Voltage: 12-32 Vdc 30mA
RJ11 connector
Cable length: 1.5 m
RJ11 to R45 custom made cable
Extended with a RJ45 adapter (up to 200 m)
Easee Link RFTM and WiFi*
HAN connection to energy meter
Monitor power consumption with the Easee app
RFID / NFC reader
*WiFi is required for normal operation. When offline, it
will continue to work via Easee Link RFTM.
Installation
Connectivity
General
6
Before you start: make sure your Easee charger is
connected to the same WiFi as you want the Equalizer
to connect to. The Equalizer does not need to be
connected to a power source during this step.
Hold the front side of the Equalizer over the light strip
of the Easee charger and move it slowly downwards.
When the charger lights green, the pairing is done!
1Pairing
Charging Robot
7
1 In most cases the HAN port will be inactive - please contact your utility
company to open it for 3rd party use.
Plug the Equalizer into a HAN port1 with the provided
cable. After around 30 seconds, it should start flashing
in white while connecting to your WiFi. Once connected,
it is automatically added to the Easee app!
Place the magnetic backside of the Equalizer directly on
a metallic surface. If a metallic surface is not available,
fix the metallic disc with a screw on the wall and then
snap the Equalizer to it.
NOTICE! For better communication with the Easee
charger, place the Equalizer outside of the fuse cabinet.
When outdoors, it should be protected from the
weather, e.g. inside the fuse box (see page 7).
21.
2.
Connecting
Fuse box
Wall mounting
for non-metallic
surfaces
1 2
8
Touch the Easee logo in the middle to check
power consumption:
Blue, fast flashing – High power consumption
Blue, slow flashing – Low power consumption
Count the flashes for percentage – 1 flash (10%),
2 flashes (20%), up to 10 flashes (100%)
Hold the Easee logo for 3 seconds to check
connectivity. You will see 2 flashes:
1st flash – Easee Link RF status
2nd flash – WiFi status
Green – Connected
Red – Not connected2
What do the
LED colors
mean?
2 Use the Easee App to set up the WiFi.
3 Please go to http://easee.support.
White, fast flashing – Booting
White, breathing every 10s – Normal operation
Red / white, switching – No WiFi added2
Red / blue, switching – No internet connection
Red, flashing – No data from power meter1
Red, breathing every 10s – Error3
3''
9
Protection
Charge faster
Product life cycle
Storage
Practical details
The Equalizer makes it possible to charge smarter, safer
and faster if the installation is scaled accordingly. To
enable its true potential, the rated value of the chargers
circuit fuse should be as high as possible compared to the
main fuse. Even in 1-phase setups, we recommend using
a 3-phase cable to future proof the installation.
The Equalizer is IP40. This means it has no protection
against water. If placed outside the house, it must be
installed inside a cabinet protected from the weather.
This product requires no maintenance. If it needs to be
repaired, please contact your Easee supplier.
The product should be stored in a tempered, dry and
well-ventilated area in order to preserve the packaging
and its contents. Relative humidity should not exceed
80% and no corrosive gas should be present. Storage
or transportation environment should never exceed
the limits provided in the technical specifications (see
page 5).
10
Disposal
Returns and complaints
Contact details
This electronic equipment must not be disposed of in
household waste. For the return of old devices, free
collection and acceptance points may be available in
your vicinity. Observe local regulations for correct and
environmentally friendly disposal.
Contact your distributor or Easee Customer Support at
easee.support regarding the return and complaint of
your product.
Easee AS
Professor Olav Hanssens vei 7A
4021 Stavanger, Norway
Org. nr: 920 292 046
You can find additional contact details for your country
at easee-international.com.
Otros manuales para Equalizer
2
Tabla de contenidos
Otros manuales de Cargador de baterías de Easee
Easee
Easee Charge Manual de usuario
Easee
Easee Charging Robot Instrucciones de montaje
Easee
Easee Charge Lite Instrucciones de montaje
Easee
Easee Equalizer Manual de usuario
Easee
Easee One Manual de usuario
Easee
Easee Ready Guía de solución de problemas
Easee
Easee Equalizer Amp Guía del usuario
Easee
Easee Home Guía de solución de problemas
Easee
Easee Ready Instrucciones de montaje
Easee
Easee Chargeberry Manual de usuario
