Dyness DYN-B4850 Manual

Dyness battery and Growatt off grid inverter Setup

Check List:

Dyness B4850 * 4

Power cable*1 pair

Parallel cable*3 pairs

Communication cable Bat-Inv*1

Communication cable Bat-Bat*3

Growatt SPF 5000TL HVM-ES

Before start, make sure battery and inverter size match.

Follow Dyness user manual to check details, it is recommended to

use battery in 1: 2 configuration.

In our case now, 5kW inverter connects to 9.6kWh battery.

Step 1 : Cable connect in inverter

Keep both inverter and battery completely off.

Connect power cable and comm cable to inverter first.

Note: Comm cable has label on, make sure the inverter side goes

to battery side, inverter side to the inverter BMS side ,battery side

left for later on in battery connection.

Step 2 : Dial DIP switch on master

Make sure host battery DIP is 0010,slaves 0000

Step 3 : Cable connect in battery

Keep batteries off, connect power cable 、parallel cable、

communication cable Bat-Inv and comm cable Bat-Bat as above.

1. Comm cable from the host CAN IN port to the inverter CAN port

2. Comm cable from the host CAN OUT to slave1 CAN IN,slave1

CAN OUT to slave2 CAN IN….

3. Power cable should be connected diagonally ,one is connected

at the top socket and another one is at the bottom.

Step 4 : Breaker/Fuse between inverter and battery

Connect DC breaker or Fuse between inverter and battery to protect

both products.

Step 5 : Switch on all the B4850 power switch,then press the

host SW button about 3S to wake up it,all the slaves will be

woken up automatically.

Step 6: Turn on the DC breaker

Step 7: Power on the inverter

Step 10: Battery and inverter are connected!

Now inverter is started, it should show the battery voltage ,battery

and inverter are connected!

Step 11: Inverter setup

Long press ENTER to set, make sure 05 are properly set as

below:

05 LI type(Lithium)

21 Cut off SOC of the battery,20% default is OK.

Step 12: You are ready to go

Step 13: Shut Down

1 Remove all the load

2 Disconnect PV/Grid

3 Turn off DC breaker between the battery and inverter.

4 Turn off the inverter power switch,shut down the inverter

5 Long press SW button to power off the battery, then switch off all

the batteries’ Power switch

Tabla de contenidos

Otros manuales de Paquete de baterías de Dyness

Dyness

Dyness Tower ESS Manual de usuario

Dyness

Dyness DL5.0C Manual de usuario

Dyness

Dyness POWERBOX Pro Manual de usuario

Dyness

Dyness B51100 Manual de usuario

Dyness

Dyness POWERCUBE Series Manual de usuario

Dyness

Dyness TowerESS Manual de usuario

Dyness

Dyness B4850 Manual de usuario

Dyness

Dyness WIFI-M01 Manual de usuario

Dyness

Dyness B3 Manual de usuario

Dyness

Dyness A48100 Manual de usuario

Dyness

Dyness Tower T Series Manual de usuario

Dyness

Dyness PowerRack HV4 Manual de usuario

Dyness

Dyness Junior Box Manual de usuario

Dyness

Dyness RV12100 Manual de usuario

Dyness

Dyness PowerDepot H5B Manual de usuario

Dyness

Dyness B48100 Manual de usuario

Manuales populares de Paquete de baterías de otras marcas

Acumentrics

Acumentrics PACK-POWER SYSTEM Manual de usuario

ACDC Dynamics

ACDC Dynamics SPF12-50 Manual de usuario

Aegis

Aegis ABL-72020P Manual de usuario

Growatt

Growatt APX 5.0P-S0-US Manual de usuario

EGO

EGO BAX1300 Manual de usuario

CyberPower

CyberPower BCA Series Manual de usuario

Intermec

Intermec 700 Series Manual de usuario

Dometic

Dometic PLB40 Manual de usuario

V-TAC

V-TAC VT-48280-W2 Manual de usuario

Valence

Valence RT Manual de usuario

Nikon

Nikon MB-D14 Manual de usuario

IOGear

IOGear GBP24V Series Manual de usuario

Inventus Power

Inventus Power PROTRXion S-12V100-TRX-HD Manual de usuario

Clas Ohlson

Clas Ohlson PW-290A Manual de usuario

EINHELL

EINHELL MULTI-Ah Power X-Change Plus Manual de usuario

Samsung

Samsung EB-U3300 Manual de usuario

ECTIVE

ECTIVE LC Series Manual de usuario

Narada

Narada 12REXC70 Manual de usuario