Dynalink RTA1046VW Manual de usuario
1
Modem Conguration Guide
Dynalink RTA1046VW
Conguring in Layer2 PPPoE for Windows XP and 2000
CONTENTS
1. Physical Connection
2. Network Configuration
3. Configuring Internet connection in Layer2 PPPoE
4. Configuring VoIP
5. Configuring Wireless
6. IPTV
7. Change of password
PLEASE NOTE: Please have your router powered on and
connected directly to your PC via Ethernet cable before you begin
as these instruction are based on Ethernet
1. PHYSICAL CONNECTION
Front Panel
Back Panel
Dynalink RTA1046VW
1. Power Supply
2. RJ45 Ethernet cable to the PC
3. PSTN Telephone handset connected to Phone1 port
– operating on VoIP (RJ11 connection)
4. RJ11 cable connecting PSTN port to Phone port on micro filter
5. RJ11 cable connecting DSL port to Modem port on micro filter
6. Line port of micro filter connecting to wall socket
1
2
3
4 5
6
2
2. NETWORK CONFIGURATION
PPPoE connection does not require you to have an IP address or DNS
settings manually encoded on your network card. PPPoE connection uses
authentication to establish the Internet connection and its after doing this
that your router is assigned an IP and DNS settings from TPG.
To begin, your PC needs to receive a private IP address from the router.
Most ADSL routers have DHCP enabled by default that will take care of
this.
To ensure your Network Card is ready for this please follow the following
steps:
A. Click on Start -> Settings -> Control Panel -> Network Connections
B. Find your Network Card then right click on this and select Properties
C. Double click on Internet Protocol TCP/IP
D. Ensure “Obtain an IP address automatically” is selected
E. Ensure “Obtain DNS server address automatically” is selected
F. Click on OK
Modem Conguration Guide Dynalink RTA1046VW
3
3. CONFIGURE IN LAYER 2 PPPOE
A. Open your browser and in the address bar type
http://192.168.1.1 and press enter.
B. Enter admin for both the username and password and
click on OK. If you have changed the login credential,
please enter the current username and password for
your router interface
C. In the “Broadband User Name” field enter:
<TPGusername>@L2TP.tpg.com.au for Fixed IP
plans OR <TPGusername>@PPP.tpg.com.au for
Dynamic IP plans (e.g. adsl1234@L2TP.tpg.com.au)
ADSL2+ customers can just use their TPG
Username without the extension (@PPP.tpg.com.
au or @L2TP.tpg.com.au)
D. In the “Password” field enter your TPG Password
Click on Connect
E. You should now get a confirmation that your
router has authenticated/connected
Modem Conguration Guide Dynalink RTA1046VW
4
Modem Conguration Guide
4. CONFIGURING VOIP
A. If you are still logged into your router interface, click on the Voice
Menu at the top. If you are not logged in anymore use your browser
to go to 192.168.1.1 and login with admin as the username and
password (by default)
B. In the SIP Basic section enter the following
information:
i. SIP Registration Address = aphone4.tpg.com.au
ii. SIP Outbound Proxy = aphone4.tpg.com.au
iii. SIP Proxy Server Address = aphone4.tpg.com.au
(Please note: For the above 3 fields, some customers
may need to use aphone3.tpg.com.au. If in doubt
please contact TPG Technical Support)
iv. Under Phone 1, enter the following information
- Phone Number = Your TPG Username (without PPP
or L2TP extension)
- Username = Your TPG Username (without PPP or
L2TP extension)
- Password = Your current TPG password
v. Click on Apply
Please note: By entering details in the ‘Phone 1’ row,
you are setting up VoIP for the phone port at the back
of your router labelled “Phone 1” and so you must
have your telephone handset connected to this port to use VoIP. If
you have a telephone handset connected at Phone 2, this would be
working on regular PSTN and not VoIP
C. You should now see a confirmation of the VoIP
connection under ‘SIP Basic Settings’
Dynalink RTA1046VW
5
Modem Conguration Guide
5. CONFIGURING WIRELESS (OPTIONAL)
Things you need to know before you begin:
- By default the RTA1046VW does not have wireless
security setup. We recommend that you follow the steps
below to set this us before you use wireless
- To use wireless be sure that you already have set up your
wireless adapter.
- To begin your wireless setup, you can connect your
computer to your router via Ethernet cable.
A. If you are still logged into your router, click on “Wireless”
in the top menu. If you are not logged in anymore use your
browser to go to 192.168.1.1 and login with admin
as the username and password (by default)
B. In the Basic settings, please check that you have
the below settings. Please take note of your SSID
(wireless network name)
C. Click on Apply
D. Click on the Security menu on the left
E. In the ‘Wireless Security’ drop down menu, select
“64-bit WEP” Click on Apply
Dynalink RTA1046VW
6
F. Select the “Hexadecimal digits” radial button
G. In the ‘Key 1’ field enter a 10-character key of your
choice consisting of only numbers 0-9 and letters
A-F (lower case is ok). This key will be used when
any computer wants to connect to your router.
Please remember this key
H. Click on Apply
I. To connect using wireless, go to Start -> Control Panel
J. Double click on ‘Network Connections’
K. Right click on your wireless adapter and go to ‘View
Available Wireless Networks’
Modem Conguration Guide Dynalink RTA1046VW
7
L. Find the SSID (network name) of your router and
click on Connect. By default the SSID should start with
RTA1046VW
M. You will now be prompted to enter your WEP Key.
N. After click on Connect
O. You should now see your status as ‘Connected’
6. IPTV
Your router is already IPTV ready, there is no need for further
configuration. To use IPTV you must first be registered.
Please refer to www.tpg.com.au/iptv for further details
7. CHANGE OF PASSWORD
For security purposes we highly recommend that you change
your password if you are using your default or if you believe your
password security has been compromised.
To change your password, first please visit
https://cyberstore.tpg.com.au/your_account/?function=changepassword.
Your new password will take approximately 10-15 minutes to take
effect, after which you must reconfigure your new password
in your router.
To change your password in your router, please follow the
following steps:
A. Open your browser and in the address bar type
http://192.168.1.1 and press enter
B. Enter admin for both the username and password and
click on OK. If you have changed the login credential,
please enter the current username and password for
your router interface
C. In the Password field, enter your new TPG password
D. Click on Connect
13 14 23tpg.com.au/support
Dynalink RTA1046VWModem Conguration Guide
PLEASE NOTE:
ADSL routers will by default be capable of automatic authentication. This means your router will use your credentials you
have provided to make the Internet connection. Each time your router is powered on, it will initialize this automated
authentication process after which your router will receive a public IP address (fixed or dynamic depending on your plan) and
DNS settings from TPG
dlink.com
Otros manuales para RTA1046VW
2
Tabla de contenidos
Otros manuales de Módem de Dynalink
Dynalink
Dynalink RTA770 Manual de usuario
Dynalink
Dynalink RTA1025W Manual de usuario
Dynalink
Dynalink RTA100+ Manual de usuario
Dynalink
Dynalink RTA1025WV6 Manual de usuario
Dynalink
Dynalink RTA1320 Manual de usuario
Dynalink
Dynalink DY56EXT3 Manual de usuario
Dynalink
Dynalink RTA1320 Manual de usuario
Dynalink
Dynalink 1456VQE-C Manual de usuario
Dynalink
Dynalink 56USBPRO Manual de usuario
Dynalink
Dynalink u90E-RURALII Manual de usuario
Manuales populares de Módem de otras marcas
US Robotics
US Robotics 3453C Manual de usuario
MaxTech
MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario
Zte
Zte MF823 Manual de usuario
Four-Faith
Four-Faith F1403 Manual de usuario
Sierra Wireless
Sierra Wireless AIRLINK MP595W Manual de usuario
Gemtek
Gemtek WiMAX WIXFBR-103 Manual de usuario