DynaColor W series Manual de usuario
003B02WXZXA3
Vandal Proof / Lightweight Fixed Dome
IP Camera
Installation Guide
Indoor / Outdoor
Ver. 1.3
2
Table of Contents
1. Indoor Camera Installation ................................................................................................... 3
1.1 Hard Ceiling ................................................................................................................. 3
1.2 In-Ceiling (T-Bar) Mounting ........................................................................................ 11
1.3 4S Mount Electrical Box ............................................................................................. 19
1.4 Corner Mounting ........................................................................................................ 22
2. Outdoor Camera Installation .............................................................................................. 26
2.1 Standard / Compact Pendant Mounting ..................................................................... 26
3. Cable Gland Installation ..................................................................................................... 31
4. Mini Dome Mounting Kit Installation .................................................................................. 34
3
1. Indoor Camera Installation
1.1 Hard Ceiling
The Fixed Dome IP Camera can be installed directly on the wall or ceiling.
Please note that the wall or ceiling must have enough strength to support the IP
Dome Camera.
Items Needed:
Vandal Proof / Lightweight Fixed Dome IP Camera
Ethernet Cable
DC Jack Cable (required without PoE)
Self-tapping Screws (supplied)
Rubber Washers (supplied)
Plastic Screw Anchors (supplied)
Tools Needed:
Tools for drilling
(+,–) Screwdriver
Follow the steps below to install the IP Dome Camera:
Step 1:
Unpack the Vandal Proof / Lightweight Fixed Dome IP Camera package and
take out the IP Dome Camera.
Step 2:
Release the two Captive Security Screws with the supplied Security Torx and
open the Dome Cover.
Vandal Proof
Lightweight
4
Figure-1: Captive Security Screw
Vandal Proof
Lightweight
Step 3:
Press both sides of the Inner Cover and remove it from the Camera Module.
Vandal Proof
Lightweight
Step 4:
Unscrew the Module-fastened Screw with the screwdriver (as indicated in the
figures below).
Vandal Proof
Lightweight
5
Step 5:
Press the sides of the Snap-on Camera Module, and detach it from the Dome
Camera’s Housing / Plate, as indicated in the figures below.
Vandal Proof
Lightweight
Step 6:
Mark the positions of the four screw holes on the base of the Dome Camera at
the chosen installation location.
Vandal Proof
Type 1
Type 2
Lightweight
Step 7:
In the marked locations, drill each
hole slightly smaller than the supplied
Screw Anchors.
6
Step 8:
Put the supplied Anchors into these drilled holes.
Step 9:
Fasten the Dome Camera’s Housing / Plate with the four supplied Self-tapping
Screws.
Vandal Proof
Lightweight
NOTE: Be sure to fix the Self-tapping Screws with the Rubber
Washers.
Vandal Proof
Lightweight
Step 10:
Thread the cables (Power / Ethernet / Audio / Alarm) through either the side
conduit entry or back conduit entry, as illustrated below. Users may use a coin
to screw off the conduit entry block for Vandal Proof IP Dome Camera.
Side Conduit Entry
Back Conduit Entry
NOTE: The Power Cable is omitted if using PoE.
7
Step 11:
Connect the ports (on the Camera Module) with their cables / wires
respectively (as shown in the figures below).
Vandal Proof
Lightweight
Step 12:
Attach the Snap-on Camera Module into / on the Dome Camera Housing /
Plate, and screw the Module-fastened Screw tightly with the screwdriver to
secure the Camera Module.
NOTE: For Vandal Proof IP Dome Camera, please install the Camera
Module with the terminal blocks facing the side cable entry (as shown in
the left figure below).
Vandal Proof
Lightweight
Step 13:
Access the Camera Browser-viewer for viewing images. Please refer to User’s
Manual for further details. Users can also use the Camera’s BNC Connector for
video output while choosing BNC as one of the streaming options in advance.
8
Step 14:
Adjust the Camera’s Pan/Tilt Holder to a desired angle, as shown below. Pan
adjustment range is nearly 360°; rotation angle range approaches to 270°. Tilt
angle is adjustable between -10° ~ 90°.
Pan Adjustment
Tilt Adjustment
NOTE: Adjust the Lens carefully within the limits mentioned above, or
the cables underneath would be harmed.
Please tighten the Camera’s Pan/Tilt Holder Screw to secure the desired tilt
angle after adjusting.
Vandal Proof
Lightweight
9
Step 15:
Adjust the Camera's zoom level and focal length via Zoom and Focus Ring
Screws.
NOTE: The zoom level and focal length might be different with the
Dome Cover on. In this case, adjusting the zoom level and the focal
length through the Dome Cover is recommended.
Vandal Proof
Lightweight
Step 16:
Put the Inner Cover back to the Camera Module.
Vandal Proof
Lightweight
10
Step 17:
Replace the Dome Cover back.
For Vandal Proof IP Dome Camera, please align the arrow mark on the Dome
Cover with the one on the Housing (as shown in the left figure below).
For Lightweight Fixed Dome IP Camera, please align the arc area on the Dome
Cover with the back conduit entry (as shown in the right figure below).
Vandal Proof
Lightweight
Step 18:
Screw on the two Captive Security Screws on the side of the Dome Cover
tightly to fasten the Dome Cover. Camera installation is complete.
Vandal Proof
Lightweight
Otros manuales para W series
2
Tabla de contenidos
Otros manuales de Cámara de seguridad de DynaColor
DynaColor
DynaColor DH701 Manual de usuario
DynaColor
DynaColor QIG-510 Series Manual de usuario
DynaColor
DynaColor NH820 Series Manual de usuario
DynaColor
DynaColor W-1 Manual de usuario
DynaColor
DynaColor NH720 Series Manual de usuario
DynaColor
DynaColor DH801 Manual de usuario
DynaColor
DynaColor S3 Manual de usuario
DynaColor
DynaColor W series Manual de usuario
DynaColor
DynaColor QIG-701-Series Manual de usuario
