dynabook Satellite C40-J Manual de usuario
March 11th, 2022
Dynabook Laptop Components Classified as Requiring Selective Treatment
Dynabook would like to communicate the method of identifying and removing
components contained in Dynabook notebook products, including but not limited to the
Satellite C40-J / Satellite Pro C40-J model, that requires selective treatment based
on the European WEEE Directive, Directive 2012/19/EU of the European Parliament
and of the Council on waste electrical and electronic equipment (WEEE).
All of the instructions provided within this letter can be reviewed in greater detail within
the Satellite C40-J / Satellite Pro C40-J Series Maintenance Manual.
Tools Required
In order to remove internal components of the Satellite C40-J / Satellite Pro C40-J some tools
from the list below may be required located in Chapter 4 Replacement Procedures of the
Dynabook Maintenance Manual
For your safety and the safety of the people around you, it is important that you use
Electrostatic Discharge (ESD) equipment. Correctly utilizing of the equipment increases the
percentage of successful repairs and saves on the cost of damaged or destroyed parts. The
following equipment is required for disassembly and assembly.
■
One Philips screwdriver with type 0 bit (for S-THIN HEAD screws)
■
One Philips screwdriver with type 1 bit (for screws other than above)
■
One flat-blade screwdriver (for removing the CPU)
■
Tweezers (for lifting screws)
■
ESD mats (lay on work table or floor)
■
An ESD wrist strap and heel grounder
■
Anti-static carpet or flooring
■
Air-ionizers in highly static sensitive areas
■
Antenna coaxial cable disconnector
■
Special syringe (for applying grease)
Table of Contents
•
(Page 2-3) Removing the Lithium Ion Battery (Main Battery, No coin cell battery)
•
(Page 4) Removing the SSD
•
(Page 5-34) LCD, Printed Circuit / Wiring Boards (PCB/ PWB system board)
•
(Page 35-36) AC Adapter and external provide cable
1. Removing the Lithium Ion Battery (Main Battery, No coin cell battery)
Please refer to the information below for instructions regarding the identification and removal of
the lithium ion battery. Further maintenance instructions can be found in section 4.2 of the
Satellite C40-J / Satellite Pro C40-J Maintenance Manual. Some tools are required in order
to remove this component. Once removed, these components should be recycled as per local
requirements.
To remove the battery, the base assembly must be removed first:
Removing Base Enclosure
Remove Base Enclosure according to the following procedures and Figure 4-7.
1.
Remove seven M2.0x7.5x4.5black Phillips head screws securing Base
Enclosure and four M2.0x.3.5x4.5black Phillips head screws securing
Base Enclosure.
2.
Remove Base Enclosure.
Figure 4-7 Removing Base Enclosure
CAUTION: When handling the battery packs, use care not to short
circuit the terminals. Do not drop, hit, twist, or bend the battery packs.
Do not scratch or break up their casing.
NOTE: Dispose of the used battery packs as required by local ordinances or
regulations.
Removing Battery Pack
Remove battery pack according to the following procedures and Figure 4-9.
1.
Remove Battery Mylar.
2.
Disconnect Battery cable from CN3 on system board.
3.
Remove four M2.0x3.5x4.5 black Phillips head screws securing Battery.
4.
Remove Battery.
Figure 4-9 Removing battery pack
CAUTION: Do not touch the connectors on SSD and in the computer with your bare
hands. SSD can fail if they are contaminated with sweat, natural oils, etc. from your
hands.
2. Removing the SSD
To remove the SSD the mainboard must be removed first.
Please refer to the information listed in section 4.8 of the Satellite C40-J / Satellite Pro C40-J
Series Maintenance Manual to check how the mainboard is removed.
Please refer to the information below for the removal of the SSD.
One Philips screwdriver with type 1 bit will be required to remove the screws indicated in the
locations below. Once removed, these components should be recycled as per local requirements.
Removing SSD
Remove SSD according to the following procedures and Figures 4-13.
1.
Remove thermally conductive pad
2.
Remove one M2_L0.3xL2.2×OD5.5×T0.6 black Phillips head screw
securing the SSD.
3.
Pull SSD from CN8 on system board.
Figure 4-13 Removing SSD
3. Removing the LCD and Printed Circuit / Wiring Boards
Beside the LCD and the main PCB, there are further small PCBs and components which are
in the scope of the WEEE Directive. The removal of these components is described in detail in
the chapter 4 of the associated maintenance manual.
Replacement Procedures
Figures
Figure 4.2 Removing Base Enclosure ...................................................................................... 4-7
Figure 4.3 Removing Battery Pack ........................................................................................ 4-9
Figure 4.4 Removing SSD ................................................................................................... 4-13
Figure 4.5 Removing SODIMM ........................................................................................... 4-14
Figure 4.6 Removing LCD Module Assembly ..................................................................... 4-17
Figure 4.7 Removing the CPU Cooling Module and Fan ..................................................... 4-19
Figure 4.7 Applying silicon grease (CPU)............................................................................. 4-20
Figure 4.8 Removing System Board ...................................................................................... 4-21
Figure 4.9 Removing IO Board ............................................................................................ 4-23
Figure 4.10 Removing Speaker .............................................................................................. 4-25
Figure 4.11 Removing the LCD Module Mask .................................................................... 4-27
Figure 4.12 Removing LCD Panel follow direction. ........................................................... 4-29
Figure 4.12 Removing the LCD cable .................................................................................. 4-32
Figure 4.12 LCD cable below the LCD module cover latch ................................................. 4-32
Figure 4.13 Removing the CCD Module .............................................................................. 4-33
Figure 4.14 Removing the Touch pad Module......................................................................4-35
4.2
Base Enclosure
Removing Base Enclosure
Remove Base Enclosure according to the following procedures and Figure 4-7.
1.
Remove seven M2.0x7.5x4.5black Phillips head screws securing Base
Enclosure and four M2.0x.3.5x4.5black Phillips head screws securing Base
Enclosure.
2.
Remove Base Enclosure.
Figure 4-7 Removing Base Enclosure
Installing Base Enclosure
Install Base Enclosure according to the following procedures and Figure 4-7.
1.
Place Base Enclosure in correct position.
2.
Secure Base Enclosure with seven M2.0x7.5x4.5black Phillips head
screws and M2.0x3.5x4.5black Phillips head screws .
CAUTION: When handling the battery packs, use care not to short
circuit the terminals. Do not drop, hit, twist, or bend the battery packs.
Do not scratch or break up their casing.
NOTE: Dispose of the used battery packs as required by local ordinances or
regulations.
4.3
Battery Pack
Removing Battery Pack
Remove battery pack according to the following procedures and Figure 4-9.
1.
Remove Battery Mylar.
2.
Disconnect Battery cable from CN3 on system board.
3.
Remove four M2.0x3.5x4.5 black Phillips head screws securing Battery.
4.
Remove Battery.
Figure 4-9Removing battery pack
CAUTION: The battery packs contain a lithium ion battery, which can
explode due to improper re placement, use, handling, or disposal. Always
dispose of the battery packs as required by local or dinances or
regulations. Use only replacement batteries recommended by Dynabook.
NOTE: Visually check the battery's terminals. If they are dirty, clean them
with a dry cloth.
Installing Battery Pack
Install battery pack according to the following procedures and Figure 4-9.
1.
Take a new or recharged Battery Pack.
2.
Place Battery Pack in correct position.
3.
Secure Battery with four M2.0x3.5x4.5 black Phillips head screws.
4.
Check the battery screw hole ,if there is cracking, please replace the parts.
5.
Connect Battery cable to CN3 on system board.
6.
Installing Battery Mylar.
CAUTION: Do not touch the connectors on SSD and in the computer with your
bare hands. SSD can fail if they are contaminated with sweat, natural oils, etc.
from your hands.
4.4
SSD
Removing SSD
Remove SSD according to the following procedures and Figures 4-13.
1.
Remove thermally conductive pad
2.
Remove one M2_L0.3xL2.2×OD5.5×T0.6 black Phillips head screw
securing the SSD.
3.
Pull SSD from CN8 on system board.
Figure 4-13 Removing SSD
Otros manuales para Satellite C40-J
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Computadora portátil de dynabook
dynabook
dynabook SATELLITE C40D-B Manual de usuario
dynabook
dynabook Satellite Pro E10-S Manual de usuario
dynabook
dynabook SATELLITE PRO C50-H Manual de usuario
dynabook
dynabook Portege X40L-K Series Manual de usuario
dynabook
dynabook PORTEGE X40-J-12Z Manual de usuario
dynabook
dynabook CS4 Series Manual de usuario
dynabook
dynabook POETEGE X30-F Series Manual de usuario
dynabook
dynabook TECRA A40-G Manual de usuario
dynabook
dynabook Satellite C40-G Manual de usuario
dynabook
dynabook Portege X30L-G Manual de usuario
dynabook
dynabook Satellite C30-K Manual de usuario
dynabook
dynabook Satellite C40-J Guía de instalación
dynabook
dynabook T 5 Series Manual de usuario
dynabook
dynabook Satellite Pro C40-G Manual de usuario
dynabook
dynabook Satellite Pro C50-J-12C Manual de usuario
dynabook
dynabook Satellite Pro C40-J Manual de usuario
dynabook
dynabook Satellite Pro R50-D Manual de usuario
dynabook
dynabook PORTEGE X30L-J Series Manual de usuario
dynabook
dynabook Satellite C50-K Manual de usuario
dynabook
dynabook PORTEGE X30W-J Manual de usuario
