Dwyer Instruments P2 Series Manual de usuario

P2 Model Flow Switches operate reliably in any mounted attitude for which they

are calibrated. Other attitudes will slightly alter actuation settings. Unless

otherwise specified, units are calibrated in the vertical inlet port down position.

Installation . . .

All plastic NPT threads should be installed using a suitable thread sealant.

(Teflon tape or Permatex "No More Leaks"). Sealant must be kept out of unit

during installation. Improper installation to a process can result in cracking.

Install fittings or adapters onto flow switch using strap wrenches. One to two

turns past hand-tight is adequate.

In-Line Flow Switches

P2 Series

DWYER INSTRUMENTS,INC.

P.O.BOX 373 MICHIGAN CITY, INDIANA46361, U.S.A.

Phone: 219/879-8000

Fax: 219/872-9057

Lit-By Fax: 888/891-4963

www.dwyer-inst.com

e-mail: [email protected]

ImportantPoints!

Product must be maintained and installed in strict accordance

with the National Electrical Code and Dwyer product catalog

and instruction bulletin. Failure to observe this warning could

result in serious injuries or damages.

For hazardous area applications involving such things as (but

not limited to) ignitable mixtures, combustible dust and

flammable materials, use an appropriate explosion-proof

enclosure or intrinsically safe interface device.

The pressure and temperature limitations shown on the

individual catalog pages and drawings for the specified flow

switches must not be exceeded. These pressures and

temperatures take into consideration possible system surge

pressures/temperatures and their frequencies.

Selection of materials for compatibility with the media is critical

to the life and operation of Dwyer products. Take care in the

properselectionofmaterialsofconstruction, particularly wetted

materials.

Life expectancy of switch contacts varies with applications.

Contact Dwyer if life cycle testing is required.

Ambient temperature changes do affect switch set points,

since the specific gravity of a liquid can vary with temperature.

Dwyer Products have been designed to resist shock and

vibration; however, shock and vibration should be minimized.

Filter liquid media containing particulate and/or debris to

ensure the proper operation of our products.

Electrical entries and mounting points in an enclosed tank

may require liquid/vapor sealing.

Dwyer Products must not be field-repaired.

Physical damage sustained by the product may render it

unserviceable.

- Warning -

The P2 is a plastic, taper-threaded instrument.

Over-tightening will result in port breakage!

Dimensional Data . . .

.78" dia.

(19.7 mm)

(25.4 mm)



4.10"

(104.3 mm) 



Retaining

Wire Piston

Assembly

Switch

Assembly

Spring

End Plug

Air (Gas) Flow Units

Only

Inlet

Outlet

Mechanical

Port Thread

Typ. 1/4" NPT

or R 1/4"

- #22 AWG PVC Lead Wire

(1/4" NPT)

- Conductor PVC Cable

(R 1/4")

P2 Flow Switches Can Be

Mounted In Various Attitudes. . .

Note: Flow settings are based on a

vertical position (inlet port down), using

water at +70°F on increasing flow. Some

variation in set point actuation will occur in

other mounting orientations.

Wetted Materials (FDA or NSF-Compliant)

Specifications . . .

Noryl®

Noryl®and Epoxy

316 Stainless Steel

150 PSI @ 70oF

50 PSI @ 212oF

212oF (100°C), Max.

50 Micron or Better

SPST, N.O. Pilot Duty 20 VA,

120-240 VAC or VDC

Housing and Barbs

Piston

Spring and Stop Pin

Pressure Rating

Operating Temperature

Required Filtration

Switch, See "Switch Ratings"

Wiring Diagram . . .

Normally Open

Switch Ratings

Max. Resistive Load

.17

.08

.13

.06

VA Volts Amps AC Amps DC

0-30

120

240

No. 22 AWG, 18" L., PVC Lead Wires

(1/4"NPT )

No. 22 AWG, 18" L., PVC

2-Conductor Cable (R 1/4")

There are four standard air flow models of the FS-3. Set point will vary

with line pressure, as shown in the graph below.

Electrical Termination

MAINTENANCE/REPAIR

Regular maintenance of the total system is recommended to assure sustained

optimum performance. These devices are not field repairable and should be

returned to the factory if recalibration or other service is required. After first obtain-

ing a Returned Goods Authorization (RGA) number, send the unit freight prepaid

to the following. Please include a clear description of the problem plus any appli-

cation information available.

Dwyer Instruments, Inc.

Attn: Repair Department

102 Highway 212

Michigan City, IN 46360

Pressure Drop Data

Flow Rate (GPM, Water)

(PSI)

Otros manuales de Cambiar de Dwyer Instruments

Dwyer Instruments

Dwyer Instruments A3000 series Manual de usuario

Dwyer Instruments

Dwyer Instruments MP Mini-Photohelic Manual de usuario

Dwyer Instruments

Dwyer Instruments CLS2 Series Manual de usuario

Dwyer Instruments

Dwyer Instruments TS-13011 Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments TSW Series Manual de usuario

Dwyer Instruments

Dwyer Instruments PROXIMITY DSS Series Manual de usuario

Dwyer Instruments

Dwyer Instruments W.E. Anderson Flotect V4 Series Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments SCS Series Manual de usuario

Dwyer Instruments

Dwyer Instruments CFS2 Series Manual de usuario

Dwyer Instruments

Dwyer Instruments PHOTOHELIC 3000 SERIES SGT Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments CMS300 Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments Mini-Photohelic MP Series Manual de usuario

Dwyer Instruments

Dwyer Instruments ADPS-08-2-N Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments F7 Series Manual de usuario

Dwyer Instruments

Dwyer Instruments 1910-00 Manual de usuario

Dwyer Instruments

Dwyer Instruments Series A3000 Photohelic Manual de usuario

Dwyer Instruments

Dwyer Instruments L8-WP FLOTECT Manual de usuario

Dwyer Instruments

Dwyer Instruments 1996 Series Manual de usuario

Dwyer Instruments

Dwyer Instruments PROXIMITY VRLS-01 Manual de usuario

Dwyer Instruments

Dwyer Instruments 530 Manual de usuario

Dwyer Instruments

Dwyer Instruments 1620 Series Manual de usuario

Dwyer Instruments

Dwyer Instruments TDS Series Manual de usuario

Dwyer Instruments

Dwyer Instruments TS2 Series Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments FLOTECT V6 series Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario