Dwyer Instruments HFPC Series Instrucciones de instalación y funcionamiento

Series HFPC & HFPS Plastic Flow Meters

Specications - Installation and Operating Instructions

Bulletin F-71

The HFPC & HFPS SERIES Flowmeters are made of injection molded, polycarbonate

and polysulfone bodies. Series HFPC and HFPS owmeters have dual scales

measuring in both GPM and LPM with ±5% full scale accuracy. Models are available

with 1/2˝, 3/4˝ or 1˝ male or female NPT connections. Female 1/2˝, 3/4˝ and 1˝ BSPP

connections are also available. Rugged construction allows these meters to handle

maximum pressures of 325 psig and 200 F. Units can be mounted in any position, even

applications with downward ow.

CAUTION: Series HFPC & HFPS Flowmeters are for indoor use only or areas

without direct sunlight. Polycarbonate & polysulfone are adversely affected by

ultraviolet light.

INSTALLATION

The casing and union retainers are made of either Polycarbonate or Polysulfone

materials permitting use with a variety of media. Use of mild detergent to clean the

meter body is encouraged to prevent damaging the label or associated components.

The meters are mounted in-line and are direct reading. The meters can be mounted

in a vertical or horizontal position as long as the uid is owing in the direction of

the arrow on the ow scale. No straight pipe is required before or after the meter. In

fact, 90° elbows can be installed on both ends without any noticeable ow variation.

When installing a meter, apply “Plumbers Tape” or “Liquid Plumber’s Sealant” on pipe

threads. If tape is used, be sure to leave 1/8˝ (3 mm) of pipe thread exposed on end

of pipe. Position lter in front of meter and in a location that allows easy access for

routine maintenance.

The meter should not be mounted in a manner such that piping misalignment or other

system components can exert force or produce a bending moment on the pressure

vessel.

To retain accuracy and repeatability internal moving parts are closely toleranced and

require ltration of at least 74 micron or a 200 mesh screen.

When installing meters onto threaded pipe caution should be taken not to over tighten

the pipe connections or introduce torque on the main body of the meter. The meter

main body may rupture if over-tightened.

SPECIFICATIONS

Service: Compatible liquids.

Wetted Materials: HFPC: Polycarbonate body, Buna-N seals, Stainless Steel

spring, Polysulfone connections. HFPS: Polysulfone body, Buna-N seals, Stainless

Steel spring, Polysulfone connections.

Maximum Pressure: 325 psig (22.4 bar).

Maximum Temperature: HFPC: 200° F (93° C) HFPS: 250° F (121° C).

Accuracy: ±2% FS.

Repeatability: ±1% FS.

Pressure Loss: See chart.

Weight: Standard models 1 lb (453.6 g). Models with optional brass connections 2

lb (907 g).

ø2-7/16

[61.91]

“L”

Meter Size Dim “L”

1/2 male

1/2 female

3/4 male

3/4 female

1 male

1 female

7-11/16 [195.26]

7-5/32 [181.76]

8-1/32 [204.00]

7-9/16 [192.09]

8-3/32 [205.58]

7-9/16 [192.09]

DWYER INSTRUMENTS, INC.

P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A.

Phone: 219/879-8000

Fax: 219/872-9057

www.dwyer-inst.com

e-mail: [email protected]

DWYER INSTRUMENTS, INC.

P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A.

Phone: 219/879-8000

Fax: 219/872-9057

www.dwyer-inst.com

e-mail: [email protected]

INSTALLATION DOS AND DON’TS

To obtain satisfactory operation from a HFPC & HFPS meters, the following points

should be considered:

DO:

• Install a pressure gauge near the inlet of the meter

• Place throttling valves at the outlet of the meter

• Use pipe sealer on the connections

• Install solenoid valves at meter outlet (as far downstream as possible)

• Mount in any orientation: vertical, horizontal or upside down

DO NOT:

• Place restrictions between the meter’s pressure gauge meter inlet

• Use in systems where reverse ow is possible

• Place meter in non-aligned piping

• Over-ow the meter by more than 150% of maximum reading

• Operate at pressures and temperatures greater than specied

• Be mounted near hot pipes or equipment which can cause damage to the pressure

vessel

• Use in systems where the assembled piping is not supported. Externally applied

piping forces may cause the meter to rupture or malfunction.

OPERATION

The meters are tubular, with all internal wetted parts sealed within the body casing

(5). Running through the center of the body casing is a tapered center shaft which is

centered in the bore. Encircling the shaft is a sharp-edged, oating metering poppet

(6). The metering poppet is held in the “no ow” position by the biased return spring

(4). As the ow moves through the meter it creates a pressure differential across the

oating orice disk, forcing the disk and transfer magnet against the return spring. As

ow increases, the pressure differential across the metering poppet increases, forcing

poppet to move along the tapered center shaft. As ow decreases, the biased return

spring forces the poppet down the tapered center shaft, returning to the “no ow”

position.

Figure 1 (Flow Meter Cross Section)

Reading the Meter

Notice the black reference line which runs 360° around the metering poppet. This

reference line moves under the scale in direct relation to the movement of the poppet.

When uid is owing, the ow rate through the meter is read by lining up the black

reference line with the closest rate line on the ow scale.

Specic Gravity or Density Effect

Standard meters are calibrated for WATER with a specic gravity of 1.0. The oating

disk meter is affected by uid density as are most other similar type meters. HFPC &

HFPS meters have less of this effect because of the sharpness of the oating orice

disks being used. The indicated ow reading will read high for heavier uids and low

for lighter uids. A corrective factor can be applied to the standard scale or a special

scale can be added at additional costs. When measuring uids with other specic

gravities, the basic equation below can be used to develop corrected readings.

CONTAMINATION AND FILTRATION

Recommended Filtration

System ltration of at least a 74 micron lter or a 200 mesh screen is recommended. It

has been found that if inadequate ltration has caused meter failure, it will normally fail

in the open position. Some systems may require a magnetic lter. IMPORTANT: Meter

damage caused by excessive contamination is not covered under warranty.

Stabilized Contamination

The goal of ltration is to create effective protection from system contamination.

Proper ltration stabilizes contamination to allow uid components to function properly.

A uid system is considered stabilized when, “contamination in” equals “contamination

out”. Proper ltration must reduce initial contamination to a stabilized level within an

acceptable time period. The system should be stabilized in time to prevent premature

wear or damage to meter components.

MAINTENANCE

Upon nal installation of the Series HFPC and HFPS Plastic Flow Meters, no routine

maintenance is required. A periodic check of the system calibration is recommended.

The Series HFPC and HFPS is not eld serviceable and should be returned if repair

is needed (eld repair should not be attempted and may void warranty). Be sure to

include a brief description of the problem plus any relevant application notes. Contact

customer service to receive a return goods authorization number before shipping.

For WATER Meters use: 1.0/Specic Gravity x scale reading

Este manual sirve para los siguientes modelos

Otros manuales de Instrumento de medición de Dwyer Instruments

Dwyer Instruments

Dwyer Instruments Magnehelic 2000-0-AF Manual de usuario

Dwyer Instruments

Dwyer Instruments A3000 series Manual de usuario

Dwyer Instruments

Dwyer Instruments DPG-100 Series Manual de usuario

Dwyer Instruments

Dwyer Instruments 45118 Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments TDS2-10 Manual de usuario

Dwyer Instruments

Dwyer Instruments UiM Coolpoint CP Series Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments TAC3 series Manual de usuario

Dwyer Instruments

Dwyer Instruments 460 Manual de uso y cuidado

Dwyer Instruments

Dwyer Instruments 477B-1 Manual

Dwyer Instruments

Dwyer Instruments MS-021 Manual de usuario

Dwyer Instruments

Dwyer Instruments A-464 Manual de usuario

Dwyer Instruments

Dwyer Instruments THI2-10 Manual de usuario

Dwyer Instruments

Dwyer Instruments Series APM Manual de usuario

Dwyer Instruments

Dwyer Instruments 160S series Manual de usuario

Dwyer Instruments

Dwyer Instruments 477B Series Manual de usuario

Dwyer Instruments

Dwyer Instruments 45158 Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments SSM Series Manual de usuario

Dwyer Instruments

Dwyer Instruments PUB-10 Manual de usuario

Dwyer Instruments

Dwyer Instruments WSM-10 Manual de usuario

Dwyer Instruments

Dwyer Instruments SCC-POT/C Manual de usuario

Dwyer Instruments

Dwyer Instruments StabiliSENSE RPMC Series Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments FLMG Series Manual de usuario

Dwyer Instruments

Dwyer Instruments 450A-1 Instrucciones de instalación y funcionamiento

Dwyer Instruments

Dwyer Instruments PUX2 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario