DURKOPP ADLER 559 - Guía del usuario

559

Automatic double-chainstitch buttonholer

Automatic single-chainstitch eyelet machine

Operating Instructions

Installation Instructions

Service Instructions

Postfach 17 03 51, D-33703 Bielefeld Potsdamer Straße 190, D-33719 Bielefeld

Telefon +49 (0) 5 21/ 9 25-00 Telefax+49(0)521/9252435www.duerkopp-adler.com

Ausgabe / Edition: 10/2005 Printed in Federal Republic of Germany Teile-Nr.:/Part-No.: 0791 559001

Anleitung, komplett / Manual, complete

559

Übersicht Summary

Bedienanleitung

Aufstellanleitung

Serviceanleitung

Bauschaltplan

9890 580001 B

Operating Instructions

Installation Instructions

Service Instructions

Interconnection-diagram

9890 580001 B

Index Page:

Part 3: Service Instructions Class 559

1. General notes

1.1 Necessaryprogramsetting......................................... 3

2. Adjusting the locking positions

2.1 General notes ................................................. 4

2.2 Hook and spreader eccentric ........................................ 5

2.3 Rotarythreadtake-updisc......................................... 6

2.4 Throweccentric................................................ 7

3. Needle bar positioning........................................... 8

4. Aligning the hook support ........................................ 9

5. Aligning the needle bar parallel to the hook support ....................... 11

6. Transversal motion of the fabric support plate ........................... 13

7. Longitudinal motion of the fabric support plate........................... 15

8. Clamping plates

8.1 Insertedclampingplates .......................................... 17

8.2 Aligning the clamping plates as to the fabric support plate ...................... 18

8.3 Adjusting the spreading ........................................... 19

8.4 Heightofthefabricclamps......................................... 21

8.5 Adjusting the locking sheet ......................................... 22

8.6 Arrestoftheclampingplates........................................ 23

8.7 Adjustingthefabricclampingpressure.................................. 24

9. Adjusting the seam width

9.1 Presettingtheseamwidth ......................................... 25

9.2 Needle zero position ............................................. 26

10. Cutting knife (Eyelet knife)

10.1 Positionofthecuttingknife......................................... 29

10.2 Adjustingtheknifeparalleltothecuttingblock............................. 31

10.3 Cuttingblockadjustment.......................................... 32

10.4 Cuttingpressure ............................................... 33

10.5 Cuttingduration................................................ 33

Index Page:

11. Hook height.................................................. 34

12. Adjusting the looping stroke....................................... 35

13. Needle bar height .............................................. 37

14. Distance between hook and needle................................... 38

15. Needle guard ................................................. 39

16. Spreader.................................................... 40

17. Spreader plate................................................ 41

18. Throat plate.................................................. 42

19. Adjusting the needle thread knife.................................... 43

20. Adjusting the fabric clamps ....................................... 45

21. Thread controller spring ......................................... 46

22. Maintenance ................................................. 47

23. Annex

23.1 Adjusting operations without head cover ................................. 48

23.2 Fusesinthecontrolbox........................................... 49

23.3 Exchange of the control ........................................... 49

24. Service menu (technician level)

24.1 Activating theservicemenu........................................ 50

24.2 Selectionofamenuitem/submenuitem................................. 50

24.3 Multitest .................................................... 50

24.4 Quittingtheservicemenu.......................................... 50

24.5 Listofmenuandsubmenuitems ..................................... 51

24.6 Menu items 500 (Configuration automatic buttonholer) ........................ 52

24.7 Menu items 550 (Configuration operation) ................................ 53

24.8 Menuitems600(Multitest)......................................... 54

25. Error messages ............................................... 59

26. Troubleshooting............................................... 64

1. General notes

The service manual on hand describes the adjustment of the automatic

buttonholer 559 in an appropriate sequence.

ATTENTION !

Various setting positions are interdependent.

Therefore it is absolutely necessary to make the individual

adjustments following the described order.

The operations described in this service manual must only be executed

by qualified staff or correspondingly instructed persons respectively!

Caution: Danger of breakage !

Before recommissioning of the automatic buttonholer after

disassembly operations first carry out the necessary adjustments

according to these service instructions.

Before all setting operations of parts involved in the stitch

formation:

–Insert a new needle without any damage.

Caution: Danger of injury !

In case of repair, alteration and maintenance work:

–Switchthemainswitchoff.

Exception:

Adjustments carried out with the help of test or adjusting programs.

Adjusting operations and function tests when the machine is

running

–Carry out adjusting operations and function tests of the running

machine only under observation of all safety measures and with

utmost caution.

Adjusting operation in the needle zone

–In order to avoid injuries remove the corresponding parts before

carrying out adjusting operations.

Exception:

The parts are absolutely necessary for the adjusting operations.

1.1 Necessary program setting

For adjusting the automatic buttonholer the following buttonhole shape

has to be set at the control panel:

–Buttonhole without bartack

–Connecting stitch = 0

–No cutting space

–Set the connecting stitch to “wide” (see chapter 9 “Setting the seam

width”)

Note!

The set seam width has to be checked not only mechanically but

also at the control panel!

2. Adjusting the locking positions

2.1 General notes

With the help of the locking positions an easy adjustment of the needle

motion to the hook and spreader motions is possible.

When the arm shaft is in staking-out position, the rotary thread take-up

disc and the eccentrics for the spreaders, the hooks and the

connecting stitch have to be in staking-out position, too.

The positions have been set by the manufacturer in such a way that

standard material can be sewn with the 559.

If you want to use other needle sizes, thread sizes or materials, you

may have to set positions slightly differing from the staking-out

position.

The locking pegs are included in the accessories of the machine and

have a diameter of 5 mm.

2.2 Hook and spreader eccentric

Caution: Danger of injury!

Switchthemainswitchoff.

Adjust the eccentrics only with the sewing machine switched off.

Standard checking

When the arm shaft is staked out with arresting pin 1, it should

be possible to stake out the hook eccentric 3 and the spreader

eccentric 4, too.

–Stake out the arm shaft with arresting pin 1.

Important !

In this position the needle bar must be in the top dead centre in

front of the left entry point.

–Check with the arresting pin 2 whether the hook eccentric 5 and the

spreader eccentric 6 can be staked out.

Correction

–Stake out the arm shaft with the arresting pin 1.

–Loosen the screws at the hook eccentric 3.

–Turn and stake out the eccentric.

–Tighten the screws.

–Loosen the screws at the spreader eccentric 4.

–Turn and stake out the eccentric.

–Tighten the screws.

64 3 25

2.3 Rotary Thread Take-up Disc

Caution: Danger of injury!

Switchthemainswitchoff.

Adjust the rotary thread take-up disc only with the sewing machine

switched off.

Standard checking

When the arm shaft has been arrested through the aressting pin 2,

so that the hook holder is in the left end position (left entry point),

the rotary thread take-up disc 6 should be in the right position

for a needle 4 that is put on the bore hole of the rotary thread take-up

disc to butt against the right surface 3.

Correction

–Remove the tension plate 1.

–Loosen the screws on the belt pulley 5.

–Push the needle 4 through the bore hole in the rotary thread

take-up disc 6.

–Turn the rotary thread take-up disc until the needle 4 butts against

the surface 3.

–Fix the screws on the belt pulley 5 again.

654 3

2.4 Throw eccentric

Caution: Danger of injury !

Switch the main switch off. Adjust the rotary thread take-up disc only

with the machine switched off.

Standard checking

When the hook support 5 is in ist right end position (right entry point),

the arresting pin 4 inserted in the eccentric 2 shoould abut in the

notching 1 at the arm.

–Turn the arm shaft in such a way that the hook support is on the

right side (right entry point).

–Put the arresting pin 4 in the drill-hole 3 of the eccentric 2.

–Check whether the arresting pin 4 abuts in the notching 1 of the

arm.

Correction

–Loosen the screws at the eccentric 2.

–Position the eccentric with the arresting pin righ ton top against the

arm.

–Tighten the screws at the eccentric 2.

43 2 1 5

3. Needle bar positioning

Caution: Danger of injury!

Exercise utmost caution when making adjustments with the machine

running.

Standard checking

When the machine positions automatically after being switched on, the

needle bar must be in the top dead centre. The hook support is in its

right end position (right entry point) then.

–Switch the machine on.

The machine positions automatically.

–Check whether the needle bar is in the top dead centre and

whether the hook support is in its right end position (right entry

point).

Correction

–Switch the machine on. The machine positions automatically.

–Move the needle bar in the correct position by handwheel (right

entry point).

–Switch to the technician level.

For this purpose press the keys “P” and “ç“ simultaneously.

–Enter code “2548”.

–Press key “OK”.

The control switches to the technician level.

–Select menu “603”.

–Press key “OK”.

–Loosen screw 1 at the switching segment 2.

–Turn the segment in such a way that the light barrier 3 at the flank

4 engages.

The switching signals are indicated on the control panel (inlet r0)

–Tighten the screw 1 at the switching segment 2.

Note:

The switching segment must be in the middle of the light barrier.

–Switch the machine on and check the positioning.

32 1 42

Otros manuales para 559 -

Tabla de contenidos

Otros manuales de Máquina de coser de DURKOPP ADLER

DURKOPP ADLER

DURKOPP ADLER 512 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 991-210-10 Series Instrucciones de funcionamiento

DURKOPP ADLER

DURKOPP ADLER 967 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 171 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 171 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 610-10 Manual de funcionamiento

DURKOPP ADLER

DURKOPP ADLER 887 Series Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 743-422 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 745-34 - Manual de usuario

DURKOPP ADLER

DURKOPP ADLER H-Type 969 Instrucciones de funcionamiento

DURKOPP ADLER

DURKOPP ADLER 888-460522 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 911-210 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER H868 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 540-100-1 Instrucciones de montaje

DURKOPP ADLER

DURKOPP ADLER 367 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 867 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 969 PURE Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 550-12-33 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 768 Manual de funcionamiento

DURKOPP ADLER

DURKOPP ADLER 8967 Guía

DURKOPP ADLER

DURKOPP ADLER 4182i-1 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 272-160362 Manual de usuario

DURKOPP ADLER

DURKOPP ADLER 477 Guía

DURKOPP ADLER

DURKOPP ADLER 610-01 Manual de usuario

Manuales populares de Máquina de coser de otras marcas

Riccar

Riccar RL634DE Manual de usuario

Singer

Singer 2517 Manual de usuario

Pfaff

Pfaff 3307-1 SERIES Manual de usuario

Janome

Janome Quilt Maker Pro 18 VERSA Manual de usuario

Siruba

Siruba C007JP Manual de usuario

Husqvarna Viking

Husqvarna Viking Designer SE Manual de usuario

Singer

Singer 148-5 Manual de usuario

IKEA

IKEA SY Manual de usuario

Pfaff

Pfaff 571 Manual de usuario

Singer

Singer 15-91 Manual de usuario

Brother

Brother BB370 Manual de usuario

Pegasus

Pegasus WT100 Series Manual de usuario

Reliable

Reliable 7100DB Manual de usuario

Pfaff

Pfaff 937 Manual de usuario

Singer

Singer 6038 Manual de usuario

Singer

Singer 413K Manual de usuario

Pfaff

Pfaff 1471 E1 Manual de usuario

Kenmore

Kenmore 16677 - Serger Sewing Machine Manual de usuario