Drogen LOBIT 100F Manual de usuario
Ages 14+
Vol 1.0
Please read the instruction manual carefully before use.
LOBIT100F
Mini FPV
- 1 -
Thank you for purchasing DROGEN products. DROGEN LOBIT 100F is designed as an easy-to-use,
full-featured RC model, capable of hovering and aerobatic flight maneuvers.
Please read the instruction manual carefully and follow all the instructions.
Be sure to retain the manual for future reference, routine maintenance and tuning.
Safety Notes
· Be cautious that this product is not designed for children under 14 years of age.
· Improper use of this product will result in serious injury.
Be aware of your personal safety, safety of others and your surrounding environment.
· Keep Lobit out of reach of children.
· It is recommended that beginners learn to fly with more experienced pilots before attempting
to fly LOBIT 100F for the first time.
· Do not operate LOBIT 100F near buildings, crowds of people, or trees to ensure the safety
of yourself, others and your LOBIT 100F.
· LOBIT 100F contains many precision electrical components.
Store the battery and Lobit in a dry area at room temperature. Exposure to water or moisture
may cause malfunction resulting in loss of responsiveness, or a crash.
· For safety, only use the included DROGEN spare parts for replacement.
· When in operation, propellers will be spinning at high speed.
The propellers are capable of inflicting serious injury or damage to property.
Be careful to keep your body and loose clothing away from the propellers.
· Never take your eyes off LOBIT 100F or leave it unattended while it is turned on.
Stop operating immediately if LOBIT 100F flies out of your sight.
· Radio interference may occur while using radio equipment
· Frequency is selectable. In case there is any interference, you can change the
setting from the range 5725 to 5825 MHz.
Carefully check all the parts of LOBIT 100F. Broken parts will pose a risk of injury and hazard.
If any problem is found before flight, do not fly LOBIT 100F. Check with call centers and local
agencies.
· Before operating, check that the batteries of the transmitter and LOBIT 100F are charged for
the flight.
· Before turning on the transmitter, check that the throttle stick is pulled completely down.
· Check the battery and power plug are securely fastened.
Severe vibration during flight may detach the plug and result in loss of control.
· When turning on LOBIT 100F, always turn on the transmitter first and then turn on LOBIT 100F.
Also, when turning off LOBIT 100F, always turn off LOBIT 100F first and then turn off the transmitter.
Safety checks before flying
Intro
Frequency (MHz) : 2400~2483.5
5725~5825
F(G,D)1(2,7)C(D,E,F,W)
A2(7,9) F(W) F9W
Radio Wave Type :
- 2 -
Safety advisory notice for
Lithium-Polymer(Lipo)Batteries
Lipo batteries are different from conventional batteries in that their chemical contents
are encased in a relatively lightweight foil packaging.
This has the advantage of significantly reducing their weight but it does make them more
susceptible to damage if roughly or inappropriately handled.
As with all batteries, there is a risk of fire or explosion if safety practices are ignored.
· Charge and store Lipo batteries in a location where a battery fire or explosion
(including smoke hazzard) will not endanger life or property.
· Keep Lipo batteries away from children and animals.
· Never charge the Lipo battery that has ballooned or swelled.
· Never charge the Lipo battery that has been punctured or damaged.
· After a crash, inspect the battery pack for signs of damage.
Discard in accordance with your country’s recycling laws.
· Never charge the Lipo battery in a moving vehicle.
· Never overcharge the Lipo battery.
· Do not charge Lipo batteries neat flammable materials or liquids.
· Ensure that charging leads are connected correctly.
Reverse polarity charging can lead to battery damage or a fire or explosion.
· Have a suitable fire extinguisher (electrical type) or a large bucket of dry sand near
the charging area. Do not try to extinguish electrical (Lipo) battery fires with water.
· Reduce risks from fire /explosion by storing and charging Lipo batteries inside a suitable container.
· Protect your Lipo battery from accidental damage during storage and transportation.
(Do not put battery packs in pockets or bags where they can short circuit or can come into
contact with sharp or metallic objects.)
· If your Lipo battery is subjected to a shock (such as a crash),place it in a metal container
and observe for signs of swelling or heating for at least 30 minutes.
· Do not attempt to disassemble or repair the Lipo battery.
Lithium-Polymer(Lipo) batteries must not be placed in with
household trash. Please contact your environmental or waste
agency or the supplier of your model for local regulations
and the location of your nearest Lipo battery recycling center.
Lipo Battery Disposal & Recycling
- 3 -
How to charge : Connect USB slot with USB charger,
then connect the USB charger to a computer
or other USB connector, such as a
smart phone charger.
The LED lights up while charging
and turns off when charging is
complete.
The voltage of the USB is +5±0.5V.
The charging time is around 40 mins
and the flying time is around 6 mins.
Charging the Lipo battery
3.7V 520mAh Lipo Battery
· Take out the battery with the battery compartment
when you storage it.
· Always power off LOBIT 100F when you charge
the battery.
Always partially charge your Lipo battery before storage.
Lipo batteries retain the power over a reasonable period.
It is not normally necessary to recharge stored Lipo batteries unless stored for periods longer
than 3-6 months. If the battery runs down, replace it.
Safety Advisory Notice for storing Lipo battery
- 4 -
MODE 1 Transmitter
Main Menu
Input Key Function
Move the stick forward or backward to make LOBIT 100F ascend or descend.
Move the stick left or right to make LOBIT 100F roll left or right.
Move the stick forward or backward to make LOBIT 100F move forward and
move backward. Move the stick left or right to make LOBIT 100F yaw left or right.
Aileron trim adjusts for left and right drift.
Elevator trim adjusts for forward and backward drift.
Rudder trim adjusts for drift of left and right rotation or yaw.
Throttle trim is normally left at neutral. The lower trim turns LEDs on and off.
Push to ON to turn on the transmitter. Push to OFF to turn off.
Throttle
/ Aileron Stick
Elevator
/ Rudder Stick
Aileron Trim
Elevator Trim
Rudder Trim
Throttle Trim
Power Switch
Photo/Video Press photo button to shoot a photo. Press video button to start recording videos
and press again to stop recording.
USB socket Only for engineer to upgrade the software , please do not use it to connect to computer.
Video glasses socket Connect video glasses (not included, needs to be purchased).
Earphone socket Connect earphone after we upgrade the transmitter, now there is no voice
transmission.
0:08:49 M1
On time
Elevator trim
Rudder trim
Throttle trim
Transmitter
Battery volcage
Ailerontrim
LCD
Photo
Elevator / Rudder Stick
Rudder Trim
Elevator Trim
Video
Throttle/Aileron stick
Aileron Trim
Throttle Trim
Power SW
Video glasses socket
Earphone socket
Micro SD Slot
Earphone socket
- 5 -
MODE 2 Transmitter
0:08:49 M2
On time
Throttle trim
Rudder trim
Elevator trim
LCD
Throttle/Rudder Stick
Rudder Trim
Throttle Trim
Video
Elevator/Aileron Stick
Aileron Trim
Elevator Trim
Power SW
Micro SD Slot
Earphone socket
Input Key Function
Move the stick forward or backward to make LOBIT 100F ascend or descend.
Move the stick left or right to yaw LOBIT 100F.
Move the stick forward or backward to make LOBIT 100F move forward and
move backward. Move the stick left or right to make LOBIT 100F roll left or right.
Aileron trim adjusts for left and right drift.
Elevator trim adjusts for forward and backward drift.
Rudder trim adjusts for drift of left and right rotation or yaw.
Throttle trim normally left at neutral. The lower trim turns LEDs on and off.
Push to ON to turn on the transmitter. Push to OFF to turn off.
Throttle
/ Rudder Stick
Elavator
/ Aileron Stick
Aileron Trim
Elevator Trim
Rudder Trim
Throttle Trim
Power Switch
Photo/Video Press photo button to shoot a photo. Press video button to start recording videos
and press again to stop recording.
USB socket Only for engineer to upgrade the software , please do not use it to connect to computer.
Video glasses socket Connect video glasses, which not included and need purchase
Earphone socket Connect earphone after we upgrade the transmitter, now there is no voice
transmission
Main Menu
Video glasses socket
Earphone socket
Photo
Transmitter
Battery volcage
Ailerontrim
- 6 -
Push both sticks to the upper
left position and hold.
Then power on the transmitter.
MODE 2
Changing mode and
transmitter stick calibration
Push the left stick to the upper left position
and right stick to the upper right position
and hold, then power on the transmitter.
You can change the mode as you like by following the instructions below.
MODE 1
Rotate both sticks twice.
MODE 1 / MODE 2
Hold down any trim until the LED on
the transmitter blinks red, indicating a
successful calibration.
MODE 1 / MODE 2
STEP
1
STEP
2
STEP
3
- 7 -
Transmitter battery installation
· Do not mix old and new batteries.
· Do not mix different types of batteries.
· Do not charge non-rechargeable batteries.
· The video will stop when the transmitter battery is low.
· When the SD card is full, it can’t record anymore and the screen will display “SD Full”.
· It is best to use a 4G+, and class 4+ SD card. Format in the transmitter before use.
· When the power on the transmitter is low, the red LED will blink quickly
and the LCD screen will turn black. The transmitter and LOBIT 100F will not bind
if the batteries are low. Please replace with new batteries.
· If the batteries in the transmitter are running low while flying the LOBIT100F,
you will still have control.
Please land the LOBIT100F and then replace batteries in the transmitter.
AA batteries according to the correct polarities.
ㅡ
+
ㅡ
+
AA
ㅡ
+
AA
ㅡ
+
AA
ㅡ
+
AA
ㅡ
+
Notice
!
- 8 -
Your transmitter will automatically find the best frequency to ensure the quality live video
transmission. In case there is any interference in your location, you can change the setting
from the range 5.725 to 5.875 Ghz to get longer range and better video transmission.
Pull down the throttle stick and press the elevator stick for about 1 second to open the setup menu.
Play Record · Set Real Time · Format SD Card
These three functions will not work on LOBIT 100F as they are for other drones.
Frequency Selectable
0:08:49 M2
0:08:49 M2
MAIN MENU
Play Record
Set Real Time
Format SD Card
Set Reverse
Set Sensitive
5.8G Frequence
▶
▶
▶
▶
▶
▶
▶
Exit
▶
▶◀
5.8G FREQUENCE
Exit
5.8 10MHz
- 9 -
Press the button on the side of the LOBIT 100F(near the SD card slot) to start recording.
A red light inside the SD card slot will blink and the two red LEDs on the LOBIT 100F will blink
alternately when recording starts.
Press the button again to stop recording. The red lights will stop blinking and the video
will be saved.
· Pressing the power button for 2 seconds will power off the LOBIT 100F.
· Carefully and properly orient the SD card for insertion in the LOBIT 100F
(see the picture above). Avoid removing the SD card and re-inserting
again too quickly otherwise the recording module will not work properly.
· First format the SD card in computer by connecting the quadcopter
with the USB cable or use SD card reader.
Always power off the LOBIT 100F before inserting or removing the SD card. Always stop
the video recording function and power off the battery first, and then you can take out
the SD card.
Camera recoding
Notice
!
Use Power button to Record Videos
SD
CARD
Tabla de contenidos
Otros manuales de Zumbido de Drogen
