Dresser Wayne HyperPIB Series Manual de usuario

INSTALLATION

Wayne Hyper

Peripheral Interface

Board (HyperPIB)

Wayne HyperPIB

Peripheral Interface Board

Installation Manual

Printed in the United States of America

Wayne 2400 Plus is a registered trademarkof Dresser Inc.

HyperPIB is a trademark of Dresser Inc.

This manual and the software described herein are furnished under license and may be used or copied only in accordance with the

terms of such license.

No part of this publication may be electronically or mechanically reproduced, stored in a retrieval system, or transmitted, in any form

or by any means, except as permitted by such license. Translation of this material to another language without express written

permission of Dresser Industries is prohibited.

The information in this publication is for informational use only and is subject to change without notice. The contents should not be

construed as a commitment by Dresser Industries, Inc. who assumes no responsibility or liability for inaccuracies that may appear in

this publication.

Dresser Wayne, Dresser Inc.

3814 Jarrett Way, Austin, TX 78728

Telephone: (512) 388-8311

Fax: (512) 388-8302

April 2003 Part No. 917404-001 Rev. B

TABLE OF CONTENTS

Section 1. Getting Started

1.1 Introduction.........................................................................................................................1-1

1.2 HyperPIB Overview............................................................................................................1-1

1.3 Required Equipment............................................................................................................1-1

Section 2. Installation

2.1 Introduction ..................................................................................................................2-3

2.2 Unpacking And Inspection ...........................................................................................2-3

2.3 Returning Damaged Components.................................................................................2-4

2.4 HyperPIB Installation ...................................................................................................2-4

2.4.1 Required Equipment .....................................................................................................2-4

2.4.2 HyperPIB Board Configuration....................................................................................2-5

2.4.2.1 Jumpers and Switches...................................................................................................2-5

2.4.2.2 Connectors....................................................................................................................2-7

2.4.2.3 LEDs.............................................................................................................................2-7

2.4.2.4 Pin Definitions..............................................................................................................2-7

2.4.3 HyperPIB Board And RS-232 Cable Installation.........................................................2-7

Table Of Contents

Part No. 917404-001 Rev. B April 2003

Warranty And Limitation Of Remedy And Liability

FCC Warning

List Of Figures

Figure 2-1 HyperPIB Board Jumper Settings............................................................................2-6

Figure 2-1 HyperPIB Board and RS-232 Installation ...............................................................2-8

List Of Tables

Table 1-1 Required Equipment ................................................................................................1-2

Table 2-1 HyperPIB Connectors..............................................................................................2-5

Table 2-2 HyperPIB LEDs.......................................................................................................2-6

Table 2-3 RS-232 (DB-25) Pin Definitions .............................................................................2-6

1-1

April 2003 Part No. 917404-001 Rev. B

GETTING STARTED

1.1 Introduction

This manual describes the installation and testing of the Wayne Hyper Peripheral Interface Board

(HyperPIB). The information is this manual is intended to be used by service representatives

installing the system and by maintenance personnel.

For additional information about the Wayne 2400/Plus™ Management Control System (2400/Plus),

refer to the following publication:

•Operation and Programming, Wayne 2400/Plus Management Control System,

part number 917434

1.2 HyperPIB Overview

Installing the HyperPIB board, part number 881415-xxx, in the site controller, allows the 2400/Plus

system to communicate with auxiliary controllers (AC). Auxiliary controllers are then able to operate

in place of the Wayne 2400 Control console when controlling Wayne dispensers. Auxiliary

controllers, such as Verifone, Suntronic, Allied or the Datarol 7100™, interface with the 2400/Plus

system with an RS-232 cable installation, part number 887902-001.

1.3 Required Equipment

The following equipment is required to install the HyperPIB board and the interface cable.

Installation

1-2

April 2003 Part No. 917404-001 Rev. B

Table 1-1. Required Equipment

Part Number Description

916962

Phillips Head Screwdriver

Anti-Static Wrist Strap

Installation

2-3

April 2003 Part No. 917404-001 Rev. B

INSTALLATION

2.1 Introduction

The following information describes how to install the HyperPIB board and the RS-232 cable

interface in the site controller.

2.2 Unpacking And Inspection

1. Before opening any cartons, count the number of cartons and verify the carton count against the

supplied packing list.

2. Inspect the cartons for damage made during transit.

3. File claim information with the carrier on the bill of lading.

4. Retain cartons suspected of damage for future claim purposes.

CAUTION: To remove electronic components from static packages, you must wear an anti-static

wrist strap, part number 916962. The wrist strap must be securely attached to an earth grounding

point to prevent possible damage from static electricity.

5. Remove all equipment from the shipping cartons and carefully inspect for damage.

NOTE: Any damage should be brought to the attention of the carrier and claims made immediately.

Return all equipment to the respective cartons for protection until actual installation is made. Save all

cartons until it is certain that return shipments are not required.

Installation

2-4

April 2003 Part No. 917404-001 Rev. B

2.3 Returning Damaged Components

Parts or components returned to the factory under warranty or for repair are subject to damage if not

packaged properly. Complete the following steps to return parts or components to the factory.

1. Place electronic components in an anti-static bag and in the original shipping cartons for return

shipment to the factory.

NOTE: If original shipping cartons are not available use a sturdy cardboard container and suitable

packing materials such as anti-static polyethylene foam or bubble pack, to ensure the component is

firmly packed.

2. Include a Return Parts Tag with the defective component describing the particular problem with

the part.

3. Make sure that adequate insurance is provided when returning parts to the factory.

WARNING: If the parts or components arrive at our factory in a damaged condition and it is

determined that the damage is a direct result of inadequate or improper packaging, the damage will

not be covered under the original warranty and the customer or distributor will be held responsible for

the cost of repairs necessary to correct or replace the damaged parts.

2.4 HyperPIB Installation

2.4.1 Required Equipment

Verify the following items are available before attempting to install the HyperPIB.

Tabla de contenidos

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario