Drayton Lifestyle Guía

SINGLE CHANNEL

Single Channel

Timeswitch

for heating OR hot water

Installation and User Instructions

06490197001 ISSA

Lifestyle

INSTALLATION INSTRUCTIONS

PLEASE NOTE: INSTALLATION MUST ONLY BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN OR

HEATING ENGINEER.

MAKE SURE MAINS INPUT HAS A 3 AMP FUSE.

The Timeswitch conforms to the essential

requirements of these Directives:

2004/108/EC – Electromagnetic compatibility

2006/95/EC – Low voltage

BEFORE INSTALLATION

First, make sure the mains supply is switched off!

USING AN EXISTING WALL-PLATE

Loosen the securing screws on the old timeswitch and unplug it.

Check that there’s 70mm clearance to the right of the wall-plate,

and 25mm above it. Now plug the unit into the wall-

plate and tighten the securing screws. Check the 3A fuse, and

switch on the mains.

FITTING A NEW WALL-PLATE

The ideal location is 1.4m above floor level, with reasonable

lighting, good access, no condensation, no extremes of

temperature, and a supporting surface that fully covers the back

of the unit.

Position with 70mm clearance to the right, 25mm above, and

sufficient room to access the securing screws underneath.

Fix, with terminals at the top, either direct to a flat wall using wall

plugs and no. 6 x 1" woodscrews, or on a flush mounting single

conduit box type UA1 (BS4662) using M3.5 x 14 bolts. DO NOT

USE A SURFACE MOUNTING BOX.

Lifestyle

WIRING THE TIMESWITCH WALL PLATE

For surface wiring, snap out the cable entry strip on the bottom

edge of the wall-plate. Lifestyle units are double-insulated and

need no earth connection, but an earthing continuity (loop)

terminal is provided for convenience.

Internal wiring

PRIOR TO MOUNTING THE UNIT SELECT THE PROGRAM SETTING

The Universal Timeswitch is selectable, which means it must be

set to the customer’s requirements as part of the installation

procedure. There are 3 options:

24-hour Program – same times, 7 days a week.

5/2-day Program – weekends different to weekday times.

7-day Program – every day of the week can be different

The factory setting is a 24-hour program. Any changes are

made with the 3 plastic headers on the back of the unit – simply

pull off the header and replace it in the new position.

1 = 24-hour program.

7 = 7-day program

No header = 5/2-day program.

After wiring, plug in the unit and tighten

the securing screws. Check the mains

input has a 3A fuse, and switch on the

mains.

ALWAYS SWITCH OFF

THE MAINS BEFORE

REMOVING THE

UNIVERSAL TIMESWITCH

–AND NEVER FIT IT TO A

LIVE WALL-PLATE!

USER’S INSTRUCTIONS

If the engineer has set your program and timings – you won’t

need to do anything else. Just keep this guide in a safe place

for future reference.

INTRODUCTION

The Lifestyle Timeswitch will automatically control your

system by switching it on and off at times that suit you. The

light on the front of the Timeswitch shows when it’s on.

PREPARING TO PROGRAMME YOUR SYSTEM

As your Timeswitch has a built-in, factory set, clock, there is no

need to set the time. However, should you need to, go to

section “Setting the Clock” Page 12.

If the timings haven’t been set for you, then this is how your

timeswitch has been set at the factory. It’s easy to make

changes. Just go to the section on the program that’s already

been selected – 24-hour, 5/2 day or 7-day – and follow the

simple instructions.

Your timeswitch has been set with these standard times.

Models Your timeswitch Instructions for the

is set as(1) model are on page

24-hour 7

5/2-day 8

7-day 10

(1) Model to be ticked by the installer

They’re based on the 5/2-day program, with different settings for

the weekend.

SWITCHING WEEKDAYS WEEKENDS

ON 1 – start of first timed period 6.30am 7.00am

OFF 1 – end of first timed period 8.30am 9.00am

ON 2 – start of second timed period* 12.00pm 12.00pm

OFF 2 – end of second timed period* 12.00pm 12.00pm

ON 3 – start of third timed period 4.30pm 4.00pm

OFF 3 – final switch-off of the day 10.30pm 11.00pm

* Notice that the second period has the same ON and OFF

times, which means neither your central heating nor hot water

will respond. If you want to activate this middle period, simply

set different ON and OFF times.

Remember:

Make your changes using the SET?, YES/-, and + buttons

found under the bottom flap.

You can’t set ON1 as the last timing before midnight, but you

can set OFF3 after midnight – providing it’s not more than 23

hours and 59 minutes after ON1.

You need to set the timings in sequence – i.e. ON1, OFF1,

ON2, OFF2, ON3, OFF3. If you get out of sequence, the display

will flash a warning.

DAY-TO-DAY VARIATIONS

Sometimes you might need to change the way you use your

system temporarily – perhaps due to an exceptionally cold day.

Here’s how to do it – without affecting your program.

Use the SELECT button under the flap to change the mode.

This won’t alter the timings in your program, which you can

return to by selecting TIMED.

OFF = continuously off.

TIMED = on for up to 3 periods a day.

ONCE = on for 1 period a day, from the start of ON1

to the end of OFF3.

ON = continuously on.

At the side of the display there are

four operating modes:

Over-riding the program

Switching on and off

On the front of the timeswitch there is an Advance/Boost button.

It allows you to switch your system either on or off, irrespective of

the program. So if the heating is off, and you want warmth now,

you can either –

1. Press Advance to switch it on (ADV will be displayed), and it will

stay on until the end of the next period. Or if the heating is on

and you don’t need it, press Advance and it will go off until the

beginning of the next ON period.

Advance will only operate in TIMED or ONCE modes.

2. Press & Hold Boost to switch on for an extra hour ( & BST will

be displayed), then Press again for two ( ) or three ( ) hours.

To cancel Boost, Press Boost again ( ). Or if the heating is

already on, using Boost will extend the ON time by one, two or

three hours.

THE 24-HOUR PROGRAM

This is the simplest program – every day’s the same. Just

follow the sequence.

Want to leave a timing as it is? Just press SET? and move on

to the next one.

Need to delete your timings and start again? Press ‘SET’ and

‘+’ together to go back to the pre-set program.

If you don’t press anything for two minutes, the timeswitch

automatically goes back to normal operation.

These instructions are for setting a 24-hour cycle that will be the

same for every day of the week – so you’ll only need to go

through the procedure once.

Press the SET? button and you’ll see ‘SET PROG?’.

Press the YES button, and you’ll see ON1, the start of your first

heating period. Adjust it in 1-minute steps using the – and +

buttons. If the – and + buttons are held down, the time

changes in 10-minute steps.

SET

PROG?

Press SET?, and you’ll see OFF1, the end of your first heating

period. Adjust this in the same way, press SET?, then repeat the

procedure for ON2, OFF2, ON3 and OFF3.

When you press SET? after setting OFF3, the timeswitch will

return to normal operation.

THE 5/2 DAY PROGRAM

Here you’ve got the option of changing times for the

weekends to cope with different demands. Just follow the

sequence, setting weekdays first.

Want to leave a timing as it is? Just press SET? and move on

to the next one.

Need to delete your timings and start again? Press ‘SET’ and

‘+’ together to go back to the pre-set program.

If you don’t press anything for two minutes, the timeswitch

automatically goes back to normal operation.

These instructions are for setting the same timings for

weekdays, and different ones for the weekend.

Set weekday times

Press the SET? button and you’ll see ‘SET PROG?’.

SET

PROG?

Press the YES button, and the display will ask ‘SET MON to FRI

PROG?’

Press YES to confirm and you’ll see ON1, the start of your first

heating period. Adjust it in 1-minute steps using the – and +

buttons. If the – and + buttons are held down, the time

changes in 10-minute steps.

Press SET?, and you’ll see OFF1, the end of your first heating

period. Adjust this in the same way, press SET?, then repeat the

procedure for ON2, OFF2, ON3 and OFF3.

Set weekend times

When you press SET? after OFF3 for weekdays, the display will

ask ‘SET SAT SUN PROG?’. Press YES, and alter the times in

the same way.

When you press SET? after OFF3 for SAT SUN, the timeswitch

will return to normal operation.

SAT SUN

PROG?

MON TUE WED THU FRI

THE 7-DAY PROGRAM

This is where you can have different timings for every day of

the week, if necessary. Just follow the sequence, setting

weekdays first.

Want to leave a timing as it is? Just press SET? and move on

to the next one.

Need to delete your timings and start again? Press ‘SET’ and

‘+’ together to go back to the pre-set program.

If you don’t press anything for two minutes, the timeswitch

automatically goes back to normal operation.

These instructions are for setting your system with the possibility

of having different timings for each day of the week.

Set all weekdays

Press the SET? button and you’ll see ‘SET PROG?’.

Press the YES button, and the display will ask ‘SET MON to FRI

PROG?’

PROG?

MON TUE WED THU FRI

SET

PROG?

Otros manuales para Lifestyle

Tabla de contenidos

Otros manuales de Cambiar de Drayton

Drayton

Drayton Tempus 1 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario