Draper 50094 Manual de usuario
These instructions accompanying the product are the original instructions. This document is part of the product,
keep it for the life of the product passing it on to any subsequent holder of the product. Read all these
instructions before assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been
designed, and contains all the necessary information to ensure its correct and safe use. By following all the
general safety instructions contained in this manual, it will ensure both product and operator safety, together
with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the
product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper
Tools policy of continuous improvement determines the right to make modifications without prior warning.
50094
PULLER KIT
HYDRAULIC
10 TONNE
1. OPERATION AND USE
The Draper hydraulic puller can be used in either 2 leg or
3 leg modes with 3 different depth settings on the legs.
First set up your puller yoke and legs in the configuration
to suit the workpiece.
- Unscrew the centre screw $ from the ram until a
total length of 80mm is withdrawn from the ram. Now
screw the hydraulic ram body into the puller yoke and
screw down until firm contact is made with the spindle
and the legs are locked into the item to be pulled.
- 2 -
$
25mm 80mm
RAM
- Now turn the ram pressure screw $ slowly into the
ram until about 25mm remains or item to be pulled is
released. Then unscrew to 80mm and re-tighten puller
by screwing ram body into yoke and repeat the
previous operation until the item being removed is
free.
Important: Do not strike the hydraulic ram with a hammer
or anything else, as this will cause the ram to fail and
invalidate warranty.
- 3 -
2. ASSEMBLY OPTIONS
Diameter range....100-150mm
Reach range..............0-90mm
Diameter range....100-150mm
Reach range............ 0-110mm
Diameter range....160-240mm
Reach range............0-150mm
Diameter range....160-240mm
Reach range............0-150mm
Diameter range....100-150mm
Reach range..............0-90mm
Diameter range....100-150mm
Reach range............ 0-110mm
Diameter range....160-240mm
Reach range............0-150mm
Diameter range....160-240mm
Reach range............0-150mm
Draper Tools Limited, Hursley Road,
Chandler's Ford, Eastleigh, Hampshire. SO53 1YF. U.K.
Helpline: (023) 8049 4344
Sales Desk: (023) 8049 4333
Internet: drapertools.com
E-mail: [email protected]
General Enquiries: (023) 8026 6355
Service/Warranty Repair Agent:
For aftersales servicing or warranty repairs, please contact the
Draper Tools Helpline for details of an agent in your local area.
©Published by Draper Tools Limited.
No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means,
electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.
CONTACTS
YOUR DRAPER STOCKIST
PJKC0118
Otros manuales de Herramientas de Draper
Draper
Draper 27118 Guía del usuario
Draper
Draper 17819 Guía del usuario
Draper
Draper PJSK Manual de usuario
Draper
Draper 17609 Guía del usuario
Draper
Draper GPAUG52-B Manual de usuario
Draper
Draper Expert 19106 Guía del usuario
Draper
Draper 18495 Guía del usuario
Draper
Draper 19525 Manual de usuario
Draper
Draper 4314K Manual de usuario
Draper
Draper 1180 Manual de usuario
Draper
Draper DTK-FORD 52576 Manual de usuario
Draper
Draper STORMFORCE 65142 Manual de usuario
Draper
Draper 23313 Manual de usuario
Draper
Draper PT2000D Manual de usuario
Draper
Draper 98421 Manual de usuario
Draper
Draper P5 Manual de usuario
Draper
Draper STORMFORCE MT400 Manual de usuario
Draper
Draper PTF Manual de usuario
Draper
Draper 5295 Manual de usuario
Draper
Draper HT/1 Manual de usuario
