Dräger X-plore 8000 Guía de configuración
Dräger X-Plore®8000 Cleaning
and Maintenance Guide
Remove and recharge the battery
To remove the battery push down on the blue battery lock tab on the reverse of the unit and fold out. Press the ‘Test’
button to check capacity and replace or recharge as necessary (Fig 2). If charging is required, connect the battery
to the charger unit, connect to a power source and wait until fully charged (Fig 3).
For more information call 01933 672180 email: info@fullsupportgroup.com
www.fullsupportgroup.com
Fig 3. Indication explanation while charging
Fig 2. Battery indicator explanation
Fig 1. Visual inspection
Visually inspect the components
Every time before use, perform a visual inspection of your equipment by checking all parts thoroughly (Fig 1).
Pay particular attention to the lter sealing surface on the fan unit for scratches, damage or contamination.
THE RPE EXPERTS
For more information call 01933 672180 email: info@fullsupportgroup.com
www.fullsupportgroup.com
Replace the lter
Remove all packaging and blue plastic guard pieces from the new lter. Remove the used
lter and splash guard by pushing the blue lter locking tab in and folding outwards (Fig 4).
For Particle lters: Gently pry the splash guard from the old lter. Inspect the new lter’s rubber
seal for damage and click the splash guard into place. Lock the clips of the lter with splash guard
into the bottom of the blower unit and fold together until you hear an audible snap (Fig 5).
For Gas lters: Unclip the splash guard from the old lter by pushing down on the indent in the
top-middle of the guard and fold outwards (Fig 5). Inspect the new lter’s rubber seal for damage.
Locate the coloured dot on the bottom middle of the front-face of the lter, indicating the lter’s
orientation. Slide the bottom clips of the splash guard into the bottom of the lter and fold
together (Fig 5). Lock the clips of the lter with splash guard into the bottom of the blower
unit and fold together until you hear an audible snap (Fig 4).
Fig. 4 Removing and attaching a
lter from the blower unit
Fig. 5 Removing and attaching the
splash guard onto a gas lter
Dräger X-Plore®8000 Cleaning
and Maintenance Guide (continued)
THE RPE EXPERTS
For more information call 01933 672180 email: info@fullsupportgroup.com
www.fullsupportgroup.com
Troubleshooting
Turning the unit on will cause it to perform a self-test for malfunctions. If an error occurs, one of the indicators
on the top of the unit will ash amber (Fig 6) or red (Fig 7) accompanied by an acoustic alarm and vibration.
NB: The residual capacity of gas lters cannot be indicated by this device.
Dräger X-Plore®8000 Cleaning
and Maintenance Guide (continued)
Fig. 6 Amber lights indicate an
issue that needs addressing
Fig. 7 Red lights indicate a serious
issue that needs addressing
THE RPE EXPERTS
For more information call 01933 672180 email: info@fullsupportgroup.com
www.fullsupportgroup.com
Replacement parts
The two rubber O-rings in the hose connector should be replaced annually to reduce malfunction.
Remove the old O-ring using the removal tool and insert a new O-ring in the groove (Fig 9).
Check the ow rate
With a lter and hose attached, turn on and wait for the self-test to complete. Cover the open end
of the breathing hose with your hand. After 5 seconds you should hear the unit start to run faster and
an alarm will be triggered. The panel will ash red indicating the air supply is blocked (Fig 8). If no
alarm is triggered, the fan speed remains unchanged, or the warning does not stop after removing
your hand - do not use and consult your supplier.
Dräger X-Plore®8000 Cleaning
and Maintenance Guide (continued)
Fig. 8 The ow rate indicator
Fig. 9 Location of the O-ring
THE RPE EXPERTS
For more information call 01933 672180 email: info@fullsupportgroup.com
www.fullsupportgroup.com
Storage
When not in use, the battery and lter should be removed. Store in a clean, dry environment,
away from direct heat sources between +50˚C and -20˚C, at a humidity of less than 95% (Fig 11).
Deeply discharged batteries may get damaged during prolonged storage. For best results,
charge batteries between 50-70% prior to storage and top up intermittently.
Cleaning
The unit should be properly cleaned before being stored. Clean using a disinfectant wipe or a damp, lint-free
cloth and allow to air dry in a well-ventilated area - as detailed in the table above (Fig 10). The use of strong
cleaning products such as chemical wipes or bleach may have an adverse effect on the unit. If used, they
should be rinsed off immediately. All cleaning and maintenance should be properly recorded. In case of
strong contamination, the fan unit can be rinsed under running water. First, make sure the rechargeable
battery remains inserted - water must not enter the battery compartment. Close suction inlet and tube
connection with protective caps (available as accessories) and rinse under clean water.
* Plugs for hose connection opening and blower inlet opening required. Battery must be connected.
Dräger X-Plore®8000 Cleaning
and Maintenance Guide (continued)
Fig. 10 Cleaning
Fig. 11 Store in a clean, dry environment
Component Cleaning Drying
PAPR Unit
Pal TECH Multi Surface Antibacterial Wipes N/A
Cleaning under running water* Open air
Carrying System Soft cloth + Sekusept® Cleaner Open air or in a drying closet (max. 60ºC)
Hose Soft cloth + Sekusept® Cleaner Open air or in a drying closet (max. 60ºC)
Filter N/A N/A
Disposable Hood N/A N/A
Reusable Hoods Soft cloth + Sekusept® Cleaner Open air or in a drying closet (max. 60ºC)
Protective Visor Soft cloth + Sekusept® Cleaner Open air or in a drying closet (max. 55ºC)
THE RPE EXPERTS
For more information call 01933 672180 email: info@fullsupportgroup.com
www.fullsupportgroup.com
Maintenance
Required
Date of
Action
Fit for use?
(please circle)
Name and
Signature
Cleanliness Yes/No
Filter
Check Yes/No
Hood Yes/No
Hose Yes/No
Valves/
Diaphragms Yes/No
Belt &
Buckles Yes/No
Battery
Charged Yes/No
Fan
Unit Yes/No
Adequate
Flow Rate Yes/No
“You must keep records of examination and testing and any repairs
made for at least 5 years” Health & Safety Executive HSG53
Serial Number:
Date Commissioned:
© Copyright 2019 FSG-0213-A
THE RPE EXPERTS
Otros manuales para X-plore 8000
18
Tabla de contenidos
Otros manuales de Producto respiratorio de Dräger
Dräger
Dräger X-plore 9500 Manual de usuario
Dräger
Dräger Panorama Nova RA Manual de usuario
Dräger
Dräger Panorama Nova S - PE/ESA Manual de usuario
Dräger
Dräger X-plore 9500 Manual de usuario
Dräger
Dräger PAS Colt Series Manual de usuario
Dräger
Dräger Oxy K 30 S Manual de usuario
Dräger
Dräger X-plore 9300 Manual de usuario
Dräger
Dräger Filterbox 40-91 Manual de usuario
Dräger
Dräger PAS Colt P18 Manual de usuario
Dräger
Dräger X-plore 2100 Manual de usuario
Dräger
Dräger X-plore 6300 Manual de usuario
Dräger
Dräger PSS AirBoss Agile Manual de usuario
Dräger
Dräger Panorama Nova S-RP Manual de usuario
Dräger
Dräger X-plore 8000 Series Manual de usuario
Dräger
Dräger X-plore 4700 Manual de usuario
Dräger
Dräger FPS 7000 Manual de usuario
Dräger
Dräger X-plore 3000 Series Manual de usuario
Dräger
Dräger PAS Series Manual de usuario
Dräger
Dräger Oxy 3000 MK II Manual de usuario
Dräger
Dräger PSS AirBoss Connect Manual de usuario
