Dover IMAJE Jaime 1000 Series Manual de usuario

IMAJE SA. reserves the right to alter the specifications and the design of this product at any time without giving prior notice.

Reproduction, in whole or in part, is not allowed.

IMAJE SA. Siège social : 9, rue Gaspard Monge B.P. 110 - 26501 BOURG-LES-VALENCE Cedex - France

: 04 75 75 56 00 - : 04 75 82 98 10 - http://www.imaje.com

Edition Anglaise

Jaime 1000 range

RS232 Link

Parallel Link

A13862

Co n t e n t s

A13862 Version E

General

General principle of a V24 exchange

Protocol

Contents

List of the V24 commands

Appendix

Parallel link

Presentation 7

Parallel link

Selection of messages 8

PRELIMINARY INSTRUCTIONS

Read all these instructions

• FIRE:

CAUTION:

Consult the safety data sheet for the ink to determine whether your printer uses

INFLAMMABLE inks and additives.

If this is the case:

– Place a foam, CO2or powder extinguisher close to the printer (maximum 10 metres).

– The printer must be kept in a well aired place away from sources of heat, flames or

sparks.

– Never leave ink, additive or cleaning solution cans or cloths soaked in ink near the

printer.

– Never smoke near the printer. Display a notice with "NO SMOKING,

INFLAMMABLE INK" close to the printer.

– Make sure to keep the printer very clean, as a dry ink deposit is highly inflammable.

– The ink, additive and cleaning solution cans must be closed and stored in a well

aired room.

• ELECTRICAL CONNECTION:

– The connection to the single phase electricity supply network must use a standard

3 pin plug with earth ; this plug must be easy to access.

– The earth connection must comply with applicable regulations.

• HEALTH:

– It is strictly forbidden to wear contact lenses when handling consumable products.

– It is recommended that ink-resistant gloves and safety goggles should be worm

during filling and cleaning operations.

Disconnect the printer from the mains power supply before any intervention.

IMAJE cannot be in any way held responsible should the above-mentioned rules not be

respected, and in general for the non-respect of elementary safety rules concerning the

utilization of these machines.

All modifications without written authorization from imaje are prohibited and

their possible consequences are the responsability of the person who performed

them.

The same applies for any use of the printer which does not comply with the

printer’s specifications.

A13862 Version E Page 1-1

REVISION

Update to instruction manual "RS232 link - parallel link for the Jaime 1000

range"

• The revision index A0 corresponds to the first edition of this manual.

• The revision index changes with every modifications.

The modified pages are mentioned in the following table. This one indicates all

updating since the first edition.

Date

of edition Document revision

index JAIME 1000

Software index Modified

pages

July 1994

July 1995

Marsh 1999

D7/A43

Initial edition

All

Page 1-2 A13862 Version E

CONTENTS

1 FOREWORD. REVISION. CONTENTS (5 pages)

2 GENERAL (14 pages)

1 Introduction 2-2

2 Description of the signals used 2-3

3 Electricalspecifications 2-4

4 Timing diagram 2-4

5 Material configuration 2-5

6 Softwareconfiguration 2-10

7 Memory aid 2-14

3 GENERAL PRINCIPLE OF A V24 EXCHANGE (3 pages)

1 General principle of a V24 exchange 3-2

4 LIST OF THE V24 COMMANDS (4 pages)

1 Sendings 4-2

2 Requests 4-3

3 List of the V24 commands 4-4

A13862 Version E Page 1-3

CONTENTS

5 PROTOCOL (64 pages)

1 Sendings concerning the printer 5-3

2 Sending concerning the print heads 5-15

3 Sendings concerning messages 5-16

4 Sendings concerning the variable elements

(counter, hour code, auto-dating) 5-26

5 Requests concerning the printer 5-31

6 Requests concerning the heads 5-44

7 Requests concerning the message 5-46

8 Requests concerning the variable elements 5-49

9 General message structures 5-52

10 Detail of the data bytes 5-53

6 APPENDIX (16 pages)

1 Examples of message programming 6-2

2 Commanding the printer by a programme in BASIC 6-9

Performance 6-13

Synoptic of a V24 exchange 6-15

Page 1-4 A13862 Version E

CONTENTS

7 PARALLEL LINK - PRESENTATION (6 pages)

1 Introduction 7-2

2 Characteristics of the Parallel link 7-3

3 Connection diagram 7-4

8 PARALLEL LINK -

SELECTION OF MESSAGES (11 pages)

1 Selection of a message from the library 8-2

2 Input signals diagram 8-4

3 Master jet, master message 8-6

4 General operation of the parallel interface 8-7

5 Restriction of the parallel interface operation 8-7

6 Usage according to printer configurations 8-8

7 Summary charts 8-11

A13862 Version E Page 1-5

GENERAL

(14 pages)

Contents

1 Introduction 2-2

2 Description of the signals used 2-3

2.1 Reference (GND) 2-3

2.2 DSR (Data Set Ready) in voltage levels transmission or

DSR+ and DSR- in loop transmission. 2-3

2.3 DTR (Data Terminal Ready) in voltage levels transmission 2-3

2.4 RTS (Request To Send) 2-3

2.5 CTS (Clear To Send) 2-3

2.6 TXD (Transmit Data) in voltage levels transmission or

TTY OUT+ and TTY OUT- in loop transmission. 2-3

2.7 TXD (Receive Data) in voltage levels transmission or

TTY IN+ and TTY IN- in loop transmission. 2-3

3 Electricalspecifications 2-4

4 Timing diagram 2-4

5 Material configuration 2-5

5.1 Presentation of the terminal block of the Industrial Interface 2-5

5.2 Configuration of the jumpers on the Industrial Interface board 2-6

5.3 Presentation of the different modes 2-7

5.4 Suggested connection diagrams 2-7

5.4.1 Slave. Voltage transmission 2-7

5.4.2 Slave. Loop transmission 2-8

5.4.3 Complete dialogue. Transmission in voltage. 2-9

6 Softwareconfiguration 2-10

6.1 Transmission speed and format on Serie 4 2-10

6.1.1 Programming 2-10

6.1.2 List of speeds and formats available 2-11

6.2 Watchdog on Serie 4 2-12

6.3 Transmission speed, format and watchdog on Serie 4 Plus 2-13

7 Memory aid 2-14

A13862 Version E Page 2-1

1 Introduction

The printers in the Jaime 1000 Series 4 range are equipped with an asynchronous series, half

duplex, interface, for connection to a V24 mode, "Voltage levels" or "20mA loop" transmission

computer.

REMINDER "20mA loop" transmission affords good immunity against electric

and electromagnetic interference. It is therefore particularly

recommendedforlongdistanceconnectionsorin a highly parasitic

area.

ATTENTION A current loop adapter is required when"20 mA current loop"

transmission is used on the S4 Plus printers.

The RS232C (or V24) standard describes the signals available during a dialog between a DTE

(Data Terminal Equipment) and a DCE (Data Communication Equipment).

A maximum of 7 signals only are used for connection to an IMAJE printer of the Jaime 1000,

whether for "voltage level" or "loop" transmission.

NOTE The Jaime 1000 printers should be considered as DTE.

ATTENTION Do not use the keyboard to make any changes to the printer during

a V24 dialogue (risk of conflicts).

You are also recommended to leave the S4 Plus printers in the

"MAIN MENU" during a V24 dialogue.

General

Page 2-2 A13862 Version E

2 Description of the signals used

2.1 Reference (GND)

Computer and printer earth in common.

2.2 DSR (Data Set Ready) in voltage levels transmission or

DSR+ and DSR- in loop transmission.

A printer input. This signal activates the V24 mode.

A symbol appears on the screen when the DSR signal is active

on S4 or on S4 Plus.

2.3 DTR (Data Terminal Ready) in voltage levels transmission

A printer output. The signal is active as soon as the printer is ready to dialog.

2.4 RTS (Request To Send)

A printer output. The signal is active at every character sequence sent by the printer.

2.5 CTS (Clear To Send)

A printer input. The signal instructs the printer to send.

2.6 TXD (Transmit Data) in voltage levels transmission or

TTY OUT+ and TTY OUT- in loop transmission.

A printer output. Data transmission.

2.7 RXD (Receive Data) in voltage levels transmission or

TTY IN+ and TTY IN- in loop transmission.

A printer input. Data reception.

General

A13862 Version E Page 2-3

Tabla de contenidos

Otros manuales de Impresora de Dover

Dover

Dover Markem Imaje SmartDate X30 Manual de usuario

Dover

Dover markem-imaje 9450 c Manual de usuario

Dover

Dover markem imaje 9750 Manual de usuario

Dover

Dover markem imaje CSAT ITS6 210 Manual de usuario

Dover

Dover markem-image SmartDate X65 Manual de usuario

Dover

Dover markem-imaje 9750 Manual de usuario

Dover

Dover Markem Imaje 9040 Manual de usuario

Dover

Dover Imaje 9020 Instrucciones de funcionamiento

Dover

Dover Markem-Imaje 5200 Manual de usuario

Dover

Dover Markem-Imaje 9410 Manual de usuario

Dover

Dover Markem-Imaje 1050 Manual de usuario

Dover

Dover Markem-Imaje 5000 Series Manual de usuario

Dover

Dover Markem Imaje 9040 Manual de usuario

Dover

Dover Markem-Imaje 1050 Manual de usuario

Dover

Dover markem-Imaje SmartDate X45 Manual de usuario

Dover

Dover Markem-Imaje 5200 Manual de usuario

Dover

Dover Markem Imaje 9330 Manual de funcionamiento

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario