Compact Digital Thermostat
DOTECH inc.
※ Pre Cautions for Use
1. This Product may cause an Electric Shock in handling, please do not attempt to open it with power turned on.
2. This Product should be install in a place fixed securely by a rack or panel.
3. This Product can be use under the following environmental conditions.
① Indoor ② Pollution Degree 2 ③ At an Altitude of 2000m or below
4. Power input must be within the designated ranges.
5. To turn on or turn off power supply for this product, please the circuit breaker or switch of a standard product of IEC 60947-1 or IEC
60947-3 product and install it within a close distance allowing convenient operation by user.
6. Please be understood that if this product is dismantled or modified discretionary, after sales service will not be able to be provided.
7. An output wire to be used for this product should be inflammable grade FV1 (V-1 grade or above), the thickness of the wire should
be AWG No. 20 or above(0.50mm2).
8. In order to prevent it from an inductive noise, please maintain the high-voltage wire and power wire separated.
9. Please avoid installing the product in a place where a strong magnetism, noise, severe vibration and impact exist.
10. When extending the sensor wire, use a shield wire and do not extend it unnecessary long.
11. The sensor wire and signal wire should be away from the power and load wires using conduits separately installed.
12. Please avoid using the product near a device generating strong high frequency noise (high-frequency welding machine,
high-frequency sewing machine, high-frequency radiotelegraph, high capacity SCR controller)
13. Product’s damages other than those decribed in the guarantee conditions provided by the manufacturer shall not be respoinsible
by us.
14. If this unit is used to control machineries (Medical equipment, vehicle, train, airplane, combustion apparatus, entertainment,
processing and transportation equipment, elevator and various safety device etc.) enabling to effect on human or property, it is
required to install fail-safe device.
※ The Aforementioned precautions must be observed, and if you fail to do so, it may cause a product’s breakdown.
※ The specifications, dimensions, and etc. are subject to change for enhancement without a prior notice.
6F, JOONGANG-ILBO B/D, 30, Dongsan-ro,
Danwon-gu, Ansan-si, Gyeonggi-do, KOREA
Tel : 82-31-495-3767, Fax : 82-31-495-3917
www.dotech21.com
User Manual
FX7SE series
1. Overview
: Basic Specification
: Components
: Accessories
: Order Information
※ Special feature
- Inside the desired temperaturetable
- Sensor error detection, Sensor calibration
- Water proof front(IP65)
- Compact size(34mm)
- RS485
- Select temperature unit (°C, ℉)
※ Specifications are subject to change without prior notice.
Bracket 2ea
DPR-TH01-AT5-2M : NTC 5KΩ at 25°C / -50~105°C / ±0.3°C at 25°C
DPR-TH01-ET-2M : NTC 5 KΩ at 25 °C / -50~105°C / ±0.3°C at 25°C
DPR-TH02-P6D100L : NTC 10 KΩ at 25 °C / -50~150°C / ±1.5°C at 25°C
List Description
Dimensions 79.5(W)mm X 36(H)mm X 39.7(D)mm
Power 200 - 230 Vac, 50/60 Hz
Consumption MAX 6 VA
Connection Screw Bolt Connector, wire range : 24~12 AWG
Input Temp. Sensor Input 1point
Output Relay Output 1point (250 Vac / 16 A or 5 A)
Operation Temp.: – 10 ~ 60°C, Humidity: Below 90 %RH
Storage Temp.: – 20 ~ 70°C, Humidity: Below 90 %RH
Model Description
FX7SE-16P-00 Basic Model, Relay Output 16A
FX7SE-16P-R4 RS485 Comm. Model, Relay Output 16A
FX7SE-05P-00 Basic Model, Relay Output 5A
FX7SE-05P-R4 RS485 Comm. Model, Relay Output 5A
- 1 -
Ø6
100
SUS PIPE SPRING PROTECT LEAD WIRE
Ø5
35
SUS PIPE SHRINK TUBE LEAD WIRE
EPOXY(Black)
20max.
6max.
LEAD WIRE(2m)
Ø6
100
SUS PIPE SPRING PROTECT LEAD WIRE
Ø5
35
SUS PIPE SHRINK TUBE LEAD WIRE
EPOXY(Black)
20max.
6max.
LEAD WIRE(2m)
Ø6
100
SUS PIPE SPRING PROTECT LEAD WIRE
Ø5
35
SUS PIPE SHRINK TUBE LEAD WIRE
EPOXY(Black)
20max.
6max.
LEAD WIRE(2m)
Product
