Dongyang Unitech D-max DWC-540F Manual de usuario
Super Wide Dynamic Range
Color Camera
사용 설명서
용서
DWC-540F
MANUAL
2
The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with limits for a
Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
WARNING - Changes or modifications not expressly approved by the manufacturer could
void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and should conform
to all local codes
3
The camera needs periodic inspection.
Contact an authorized technician for inspection.
Stop using your camera when you find a malfunction.
If you use your camera around smoke or unusual heat for a long time,
fire may be caused.
Do not install the camera on a surface that can not support it.
Unless the surface is suitable, it could cause falling or other hazards.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not disassemble the camera.
It may result in fire, electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in fire or other hazards.
■ Warning
4
1. Features
--------------------------------
2. Components & Cable Connection
---------------------------------
3. Names and functions of parts
---------------------------------
4. Installation
---------------------------------
5. Setup Menu flow
--------------------------------
6. Setup page menu
---------------------------------
7. Special page 1 menu
---------------------------------
8. Special page 2 menu
---------------------------------
9. Troubleshooting
---------------------------------
10. Specifications
---------------------------------
■Contents
5
☺ High resolution color for crisp, clear video
▪Progressive image capture
▪ 540 HTVL equivalent
☺ High sensitivity for low-light images
▪ Advanced noise reduction technology
☺ Wide Dynamic Range provides excellent quality in high-contrast
environments
▪ 120dB maximum dynamic range
☺ Optimum Exposure Mode presets
▪Best pictures in a variety of applications
☺ EDNR (Electronic Digital Noise Reduction)
▪ The amount of low illuminance noise has been significantly reduced,
and the signal-to-noise ratio (S/N ratio) as well as horizontal resolution have
been improved, resulting in a clear and sharp image display even in the dark.
☺Controlled by OSD Menu
▪ The camera can be controlled by selecting text displayed on the monitor screen.
☺Additional Functions
▪ Automatic White Balance
▪ Backlight compensation
▪ Automatic Gain Control
▪ Activity / motion detection
▪ Digital Pan / Tilt / Zoom
▪ Day / Night
1. Features
6
1)
COLOR CAMERA
-------------
2)
AUTO IRIS LENS CONNECTION
PLUG
-------------
3)
C-MOUNT ADAPTOR
-------------
4)
L-WRENCH
-------------
5)
MANUAL
-------------
2. Components
7
1) Front
① Lens protection cap
Please cover the lens when it is not in use.
② CS-Mount lens adaptor
Please attach the CS-Mount lens here.
③ Back Focus clamp screw
Please loosen the clamp screw with a screwdriver before adjusting the Back focal
length.
☞Mounting bracket screw hole
Please use the screw hole when fixing the
camera onto the mounting bracket. Please use
the clamp screw as specified in the picture.
3. Names and Functions of Parts
8
☞The mounting bracket can be separated and attached to the top of the camera.
In this instance please do not tighten the screw to a depth of more than 5mm,
otherwise serious damage can occur to the inner parts of the camera.
2) Back
②
④
⑤
① ③
① Auto iris lens connector
This is the connection terminal for the auto iris lens.
② Video output terminal
Sends video signals and connects to the video input terminal of the monitor.
③ Power lamp
Lights up when the correct power is supplied to the camera.
④ Setting button
SETUP button : Used for the menu display. This button can be used to confirm
settings after changing the value of the selected function or current conditions.
UP & DOWN buttons : Used for selecting items by moving the cursor up
Or down on the menu screen.
LEFT & RIGHT buttons : Used when changing item values, by moving
the cursor to the left or right on the menu screen.
⑤ Power input terminal
Connects to the power appropriate to each power requirement.
9
1) Lens
Lenses are sold separately. Lenses such as auto iris lens, CS-Mount lens and C-Mount
lens can be used.
Note)
• Use of the DC auto iris lens is recommended to achieve the best results for operating this
product effectively.
• Please keep the lens clean.
• Any foreign objects and finger marks on the lens can cause inferior image quality in low
light level conditions.
①When using an auto iris lens
- Please peel off about 8mm of the outer skin of the auto iris lens cable.
- Please peel off about 2mm of the outer skin of the insulated conductor inside the
lens cable
4. Installation
10
- Please remove the cover of the auto iris lens connection plug and solder the lens
cable to the connector pin in the plug.
LENS
Pin No. DC VIDEO
No.1 Pin Damping- Red(power)
No.2 Pin Damping+ NC
No.3 Pin Drive+ White(video signal)
No.4 Pin Drive- Black(GND)
- Please replace the auto iris lens connection plug cover and take off the lens
protection cap, and then attach the auto iris lens to the camera by screwing it in
clockwise.
- Please insert the connection plug that is connected to the auto iris lens cable into
the auto lens connector, which is located on the back of the camera
Tabla de contenidos
Otros manuales de Cámara de seguridad de Dongyang Unitech
