Dong Gu Co VENUSTA MASTER Manual de usuario
.
1. Contents / Accessories ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 1
2. Note ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 2
3. Description of part ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 3
4. Installation – Bean hopper ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 4
5. Installation – Canister and Milk cooler ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 5
6. Installation – How to install the machine ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 6
7. Installation – adjust coffee bean grind level/How to use setting button ‥‥‥‥‥‥‥ 7
8. Display icons ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 8
9. Ingredients setting ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 9
10. Price unit setting ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 10
11. Price setting ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 11
12. Hot water temperature setting ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 12
13. Counting sales cups ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 13
14. Counting sales amount ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 14
15. Cake counting setting ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 15
16. Cup sensor setting ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 16
17. Cup volume setting ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 17
18. Initialization of recipe / End Mode ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 18
19. Error messages & checking / Part disassembly ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 19
20. Part disassembly ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 20
21. How to clean and cleaning schedule ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 21
22. How to replace fuse / Specification ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 23
THM screw
(2pcs)
(P4 / 2pcs)
Waste box Water Tray
2
This section refers all instruction to use product in safe and correct way.
Be sure to follow all instructions to prevent any accidents and danger.
Do not disassemble without
confirmation from authorized
service agent.
●Might cause electric
shock or fire.
Do not clean with
water on machine
directly or with
benzene, thinner.
●Electrical shock or damage
in parts by any chance.
The warning mark refers possibility
of significant danger, death and fire
if user do not follow instructions.
The caution mark refers possibility
of damage, injury and loss if user
do not follow instructions.
Ground
outlet
AC 220V outlet
AC 220V outlet
Do not connect multiple
plugs of appliances
to one oulet at the
same time and do
not connect electrical plug
to outlet when the outlets is loose.
When stop operating the machine
for a long time, unplug power
to the machine and empty
bean hopper & canisters.
●It might cause trouble.
Use of subterranean water, tap water
cause problem in operation due to
calcification.
Recommend to use only the water
filtered by UF Membrane filter.
Stop operation when
the plug and outlet
is damaged.
●It might cause electric shock or fire.
●Be sure to call your local A/S service team to repair it.
Do not handle the power
cord with wet hand.
●It might cause fire or electric
shock.
●
Do not keep inflammables
near by machine
or put it into.
●It might cause
explosion, fire and injury.
Be sure to operate the machine
for indoor-use only at room
temperature.
●It might cause burst in winter
when keep it outside.
●It might cause an electric
leakage and fire due to rain
or snow.
●At the place below 0℃, be
sure to turn on machine.
●It might cause fire.
Thinner
Gasoline
LPG
In winter season, there would be a possibility
of freeze and burst . Make sure to use
the equipment at room temperature and
keep turning power on.
※
Manufacturer will not be responsible for
any damages or troubles caused by freeze
and burst.
Be sure to use only
grounded outlet when
connect the electrical
plug to the outlet.
●It might cause fire or electric
shock.
3
Bean Hopper
Display
Door nozzle
Cup sensor
Water tray
Fuse
Power switch
Exhaust fan
Bean hopper
Grinder
Brewer mech
Drinks button Power cord Water supply inlet
Drain
outlet
Drinks name
panel cover
[Setting button]
①Mode open button
②Mode move /
initialization brewer mech
③Increase button
Brewer cleaning button
④Decrease button
Mixing ball cleaning
button
Mixing ball
Milk hose
Steam device assem
Nozzle
Waste box
Drain bucket
Canister
*VENUSTA MASTER-E:
canister 4pcs / mixing bowl 3pcs
*VENUSTA MASTER:
canister 3pcs / mixing bowl 2pcs
Program update
panel
1
2
3
5
4
Fit the bracket into the bean hopper connecting pipe as figure.
Then screw THM Screw (2pcs) to the hole of main chassis and the fixing bracket tightly.
(THM Screws packed in the accessory part.)
THM
scerw
Press bean hopper connecting pipe downward and fit to the worm lever.
Bean hopper connecting pipe
Worm lever
Bean Hopper
Fixing Bracket
Fit the bean hopper into hole of the bean hopper holder as figure.
Turn the bean hopper connecting pipe anticlockwise to fix it.
The bean hopper can be removed during operating unless fix it.
Fit the bean baffle plate into the bean hopper hole and push
the plate completely to get the bean outlet open.
When do not push the plate completely, the bean is not able to be
supplied to grinder, which cause trouble in vending a cup.
①Close ②Open
Fill the bean hopper with coffee bean.
Be sure to use roasted whole bean only, not pre-ground coffee.
Pre-ground coffee cause trouble.
Recommend to use Arabica coffee bean for espresso and do not use over
roasted bean.
5
1
2
3
-
Grab the handle and lift the canister up slightly and pull
front part of canister toward user.
①
②
Smoothly push the canister on the Canister stopper as below picture.
Then, the canister chute will be opened automatically.
①②
Canister
Stopper
1.Turn on the Milk cooler and
disassemble beside the cap.
Cap
2.Put the connect –N1 in the hole and turn right to fit.
3.Put the milk bottle in the Milk cooler as below picture.
The milk hose should be lain on ground of milk bottle.
Connect-N1
Milk
When filling up ingredients, Be sure to rotate the ingredient chute so
that it points up (loading position).
And slide canister backward and hold it carefully to prevent spilling.
Fill canisters with toppings correctly and close canister lid.
6
1
2
3
4
Fill the canister with Powder and Coffee beans
Try to do Bean Volume test for 2~3 times
Turn on the machine. (the plug must be connected to power outlet
which has ground)
Put your cup on the nozzle and press any menu button.
Take the cup out when machine operating is completed.
*To warm up the machine, press first drink menu button more than 5 seconds.
Clean the machine.
Place the machine on a flat level.
●If it is not leveled, it might cause noise.
●Space of 15cm from wall is required when install.
Connect water supply hose
1. Connect water supply hose to pipe connector
at rear side of machine.
※(1) connect pipe - silicone hose (2) water bottle - hose
●Be cautious to prevent the sliced side of the hose from clinging to the internal
side or bottom of the bottle. ( It might cause problem in water supply )
●Be sure to use the cover to prevent that any impurities may get into the bottle.
It might cause trouble.
Connect drain hose
1. Drain Bottle should be installed below side of machine.
2. Adjust the length of drain hose properly to let
the drain hose 5~10cm below from the top of the bottle.
If the hose and drain bottle is not installed incorrectly, it might cause
water back flow into machine.
If the drain hose would be bent, it might cause water back flow.
※Depending on the water used might cause calcification
inside of internal components.
Recommended to check it in every 6 months to prevent
any problem in machine working.
Be sure to use water filtered by UF Membrane filter.
Water Supply Connector
Drain Connector
1
fine
coarse
fine
coarse
worm
lever
Able to adjust the level by rotating the worm lever
equipped in the upside ofgrinder.
●The grind level is verified from 1 to 7 level and factory
setting level is 4.
●If set at too fine or too coarse level,it might cause
trouble in extracting espresso.
Recommend to set at from 3 to 5 level.
1. Press the “Setting/Reset” button inside door.
2. Press the Mode button 2 or 3 times to test bean volume and to fill the grinder with ground bean.
* Press 1 time: Will be open the mode.
* Fill water sign: Press “Setting/Reset” button when displayed “Fill water sign”.
* Milk line cleaning: Prepare a cup of pure water under Milk nozzle (Connecter-N1)
to clean milk line.(Only VENUSTA MASTER-S)
Press Setting/Cancel button more than 3 seconds.
* Press Mode button/Brewer Reset button more than 3 seconds to initialize
the brewer mech.
* When Mode opened, it will be used Moving button.
* Press Increase button/Cleaning button more than 3 seconds to clean the brewer mech.
* When Mode opened, it will be used Increase button.
* Press Decrease button / clean mix button more than 3seconds to clean
all mixing bowls.
* When Mode opened, it will be used decrease button.
* Press 1 time: Will be open the mode.
* Fill water sign: Press “Setting/Reset” button when displayed “Fill water sign”.
* Milk line cleaning: Prepare a cup of pure water under Milk nozzle (Connecter-N1)
to clean milk line.(Only VENUSTA MASTER-S)
Press Setting/Cancel button more than 3 seconds.
* Press Mode button/Brewer Reset button more than 3 seconds to initialize
the brewer mech.
* When Mode opened, it will be used Moving button.
* Press Increase button/Cleaning button more than 3 seconds to clean the brewer mech.
* When Mode opened, it will be used Increase button.
* Press Decrease button / clean mix button more than 3seconds to clean
all mixing bowls.
* When Mode opened, it will be used decrease button.
※It’s displayed machine operating & setting values.
Explanation of IconFigure Explanation of IconFigure
* When Grinding or Bean volume setting.
* When espresso operating or water volume
setting for espresso
* When hot water coming out or water volume
setting for drinks
* It will be displayed with error code
* When powder’s volume adjusting
* When Powder’s volume adjusting
(the number will be shown canister location)
* When heater operating
* When water tank empty
* When filled with cake
* When water volume setting /
when powder mixing
* It’s displayed error code or setting
values.
* When Steam operating
* When the brewer mech isn’t mounted
* When the brew mech initializing
1
2
3
When displayed “SET”, press dinks menu button
to adjust ingredient volume and water volume.
Press Increase/Decrease button inside door
to adjust menu’s recipe.
It goes for next recipe if you press same drink menu
again.
Press the Setting/Reset button inside door.
Display will be shown “SET”.
When you finish setting, press Mode/Brewer Reset
button to meve “End” mode.
When “End mode”, if you press Setting/Reset button
or any kind menu button, the machine return
to standby mode.
*When Mode, if you don’t press any button more than
30 seconds, the machine return to standby mode
automatically.
[Bean volume testing]
1. Remove brewer mech.
2. Get in mode by pressing Setting/Cancel button inside door.
3. If you press any kind menu when displayed “SET”,
display will be shown bean volumes.
4. Put some cup as figure
5. When displayed bean volumes, press drink menu button
as you want to set.
You can check volume of bean as you set.
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Cafetera de Dong Gu Co
