Dometic DOTRC11B Manual de usuario
MODEL NO.: DOTRC11B, DOTRC11W
Please read and save these
installation instructions.
P/N: 3828W5U0043
OVER THE RANGE
MICROWAVE OVEN
INSTALLATION
INSTRUCTIONS
Read this entire manual before you begin.
BEFORE YOU START
• Proper installation is the installer's responsibility!
– Write the model & serial numbers on the owner’s manual. The model number label is located on the oven
front. See Figure 1. The mounting plate is located on the back side of the microwave oven. See Figure 2.
BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS:
FOR YOUR SAFETY:
• You will need TWO people to install this oven. It is heavy and could cause personal injury if not handled
properly. The dimensions of the oven are as follows:
Height : 163/16 inches
Width : 29 7/8inches
Depth : 14 inches
Weight : 69 pounds
• Avoid Electrical Shock!
– Before you drill into the wall, note where electrical outlets are and where electrical wires might be
concealed behind the wall. YOU COULD GET AN ELECTRIC SHOCK if you contact electrical wires
with your drill bit.
– Locate and disconnect the power to any electrical circuits that could be affected by installing this oven.
IF YOU DO NOT DISCONNECT THE POWER, YOU COULD GET AN ELECTRIC SHOCK.
• ELECTRICAL RATING OF THIS OVEN : 120V AC 60Hz.
12 A / 1300 W (Microwave oven only)
13 A / 1500 W (Microwave oven + Cooktop Lamps + Ventilation Fan)
– You need a DEDICATED 120V, 60Hz, AC only, 15 or 20A, fused electrical supply (located in the cabinet
above the microwave as close as possible to the microwave) serving only the microwave.
YOUR SAFETY FIRST
Model Number Label
Figure 1
Mounting
plate
( Remove from
oven to install. )
Back of oven
Figure 2
W A R N I N G
–2 –
• THIS APPLIANCE MUST BE GROUNDED!
–If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape
wire for the electric current. This appliance is equipped with a cord having a grounding wire with a
grounding plug.
•Place the plug into a properly installed and grounded outlet. See Figure 3.
•Do not use an extension cord.
•Keep the power cord dry and do not pinch or crush it.
• DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE
POWER SUPPLY CORD GROUNDING PRONG!
This appliance MUST be grounded!
If you use the grounding plug improperly, you risk electric shock!
–Check with a qualified electrician if you are not sure whether the oven is properly grounded or if you do not
completely understand the grounding instructions.
DO NOT USE A FUSE IN THE NEUTRAL OR GROUNDING CIRCUIT.
Improper grounding could result in electric shock or other personal injury.
SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR'S USE.
• DO NOT EXPOSE YOURSELF TO EXCESSIVE MICROWAVE ENERGY!
–DO NOT try to operate the microwave oven with the door open.
–DO NOT tamper with or defeat the safety interlocks.
–DO NOT place objects between the microwave oven front face and the door.
–
DO NOT allow soil or cleaner residue to build up on the flat surfaces around the microwave oven door.
–DO NOT operate the microwave oven if it is damaged.
–The microwave oven door must close properly to operate safely.
–DO NOT USE THE MICROWAVE OVEN:
•If the door is bent.
•If the hinges or latches are broken or loose.
•If the door seals, sealing surfaces or glass is broken.
–DO NOT ATTEMPT TO ADJUST OR REPAIR THE OVEN YOURSELF!
It should be adjusted and repaired by a qualified technician who can check for microwave leakage after
repairing the oven.
If you do not use the microwave oven as instructed,
you could be exposed to excessive microwave energy.
YOUR SAFETY FIRST
PROPERLY POLARIZED AND
GROUNDED OUTLET
Three-Pronged (Grounding) Plug
Figure 3
W A R N I N G
W A R N I N G
W A R N I N G
–3 –
• MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT.
–Mount the oven against a flat, vertical wall, so it is supported by the wall. The wall should be constructed
to support 150 lbs.
–ATTACH AT LEAST ONE of the two lag screws supporting the oven to a vertical, frame member.
–DO NOT mount the microwave oven to an island or peninsula cabinet.
–BE SURE the upper cabinet and rear wall structures are able to support 150 lbs., plus the weight of any
items you place inside the oven or upper cabinet.
–Locate the oven away from strong draft areas, such as windows, doors, and strong heating vents.
–BE SURE you have enough space. See Figure 4 below for minimum vertical and horizontal clearance.
If you do not mount the oven as instructed,
you risk personal injury and/or property damage.
C A U T I O N
•Before you begin installing the oven, PLACE A PIECE OF THE CARTON OR OTHER HEAVY
MATERIAL (a blanket) over the countertop or cooktop to protect it. Do not use a plastic cover.
Failure to protect these surfaces could result in property damage.
YOUR SAFETY FIRST
30" min. cabinet opening width
30" min. clearance from bottom
of cabinet to cooking surface
or countertop
(Use templates included
with installation instructions)
Grounded Outlet
(inside upper cabinet)
Power Supply Cord Hole
Figure 4
W A R N I N G
–4 –
THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN:
NOTE: Depending on your ventilation requirements, you may not use all of these parts.
NOTE: You need to install at least one lag screw into a 2" x 4" stud and four anchor bolts into the wall.
The mounting area must meet the 150 lbs. weight requirement.
PARTS, TOOLS, MATERIALS
Backdraft damper / duct connector
(for roof-venting or wall-venting installation)
Not Actual Size ( 2 pieces must be
assembled as shown )
One power cord clamp and
One dark-colored mounting screw
(to hold the power cord)
Actual Size
Two self - tapping screws - Actual Size
(for attaching the damper duct connector)
Four 1/4" x 2" lag screws - Actual Size
(for wall stud holes)
Two 1/4" x 2" bolts - Actual Size
(for securing to the upper cabinet) Four spring toggle heads - Actual Size
(for the toggle bolts)
Two washers - Actual Size
(for the two upper cabinet bolts)
Four 1/4" x 3" toggle bolts - Actual Size
(for drywall holes)
One power cord clamp bushing - Actual Size
(for the cord hole in a metal upper cabinet)
One lock pin and one washer-Not Actual size
–5 –
YOU WILL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE INSTALLATION:
Carton or other heavy material for covering the counter top.
•If you have brick or masonry walls, you will need special hardware and tools.
•The ductwork you need for the installation is not included. All wall and roof caps must have a back-draft
damper.(Shown on page 5.)
PARTS, TOOLS, MATERIALS
Clear tape
(for taping the templates to the wall) Stud finder or thin nail.
Saber saw (for cutting vent
holes for roof or wall venting)
Keyhole saw (for the power cord hole)
Electric drill
3/8" and 3/4" wood drill bits
1/2" and 3/16"
drill bits
Phillips screwdriver (for the screws)
Pencil
Flat blade screwdriver (for the toggle bolts)
Measuring tape (metal preferred)
Small side cutters or tin snips Caulking gun
Plumb line
Duct Tape
–6 –
AVOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED!
1. Locate the grounded electric outlet for this oven in the
cabinet above the oven, as shown in Figure 4.
NOTE: The outlet should be on a circuit dedicated to the
microwave oven (120V, 60Hz., AC only) with a
15 or 20A fused electrical supply.
IMPORTANT: If you do not have the proper wall outlet, you
MUST have one installed by a qualified
electrician.
2. You will cut the power-supply-cord hole (shown in
Figure 4) later when you prepare the wall and upper cabinet
in Step 4.
NOTE: Do not use an extension cord.
Keep the power cord dry and do not pinch or crush it.
Improper grounding could result in
electric shock or other personal injury.
•DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE POWER SUPPLY
CORD GROUNDING PRONG!
This appliance MUST be grounded!
STEP 1: PREPARE THE
ELECTRICAL CONNECTIONS
Grounded Outlet
( Inside Cabinet )
Upper
Cabinet
Power-Supply-Cord Hole
Figure 4
W A R N I N G
W A R N I N G
–7 –
NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork
fittings and length are shown in Figure 9, page 9.
THIS OVEN MUST BE PROPERLY VENTED!
You may vent your oven in one of three ways. However, do NOT vent into a wall cavity, an attic,
or an unused area.
Roof-venting If your oven is located on an outside wall near the roof, as in Figures 6 (31/4" x
10" duct) and 8 (6" round duct.)
Wall-venting If your oven is located on an outside wall of your house, as in Figure 5 (31/4" x 10"
duct) and Figure 8 (6" round duct.)
Room-venting If your oven is located on an inside wall of your house, as in Figure 7.
NOTE: If you choose the rear exhaust method (roof-or wall-venting), be sure there is enough clearance
within the wall for the exhaust duct.
REMEMBER AS YOU INSTALL THE
VENTING:
•Keep the length of the ductwork and the
number of elbows to a minimum to ventilate
your oven efficiently.
See examples on page 9.
•Keep the size of the ductwork the same.
•Do not install two elbows together.
•Use duct tape to seal all joints in the duct
system.
•Use caulking to seal the exterior wall or
roof opening around the cap.
STEP 2:
PREPARE THE VENTING SYSTEM
Wall Venting
Wall venting through-the-wall
wall cap
3 1/4"x10"
duct
Figure 5
cabinet
oven
Roof Venting
through-the-roof
3 1/4"x10"
duct
Figure 6
roof cap
Roof venting
cabinet
oven
6" min.
diameter
round duct
3 1/4" to round
duct transition 3 1/4" to round
ductwork transition
Figure 8
roof cap
wall cap
elbow
W A R N I N G -F I R E H A Z A R D
Room Venting
Figure 7
cabinet
oven
–8 –
STANDARD FITTINGS
NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3"
extension duct installed between the damper assembly and the adapter to prevent the exhaust
damper’s sticking.
DUCT LENGTH
The total length of the duct system, including straight duct, elbows, transitions, and wall or roof caps must
not exceed the equivalent of 140 feet.
For best performance, do not use more than three 90 degree elbows.
Below are the standard fittings and their equivalent length in feet.
To calculate the equivalent length of each ductpiece used, see the examples below.
STEP 2:
PREPARE THE VENTING SYSYTEM
Figure 9
1
4567
23
3 1/4"x10"
to 6"=5ft.
90˚elbow
=10ft. 45˚elbow
=5ft.
3 1/4"x10"
wall cap
=40ft.
3 1/4"x10"
flat elbow
=10ft.
3 1/4"x10" roof
cap=24ft. 3 1/4"x10" 90˚
elbow=25ft.
Examples
For 3 1/4"x10" SYSTEMS
1-3 1/4" x 10" 90˚elbow
1-Wall Cap
8 feet straight duct
TOTAL LENGTH
1-transition
2-90˚elbows
1-Wall Cap
8 feet straight
TOTAL LENGTH
For 6" ROUND SYSTEMS
6ft.
2ft. 2ft.
3 1/4"x10"
90˚elbow wall cap 6ft.
90˚elbows
transition
wall cap
= 25 ft.
= 40 ft.
= 8 ft.
= 73 ft.
= 5 ft.
= 20 ft.
= 40 ft.
= 8 ft.
= 73 ft.
–9 –
ELECTRICAL SHOCK HAZARD!
UNPLUG UNIT BEFORE WORKING ON IT.
•DO NOT PULL OR STRETCH THE BLOWER WIRING!
Pulling and stretching the blower wiring could result in electrical shock.
Remove the two vent grille mounting screws and tip the vent
grille forward, then lift it out. See Figure 10.
Loosen the two rod retainer screws behind the vent grille.
See Figure 10-1, remove the wall mounting plate from the
back of the oven and set aside.
WALL-VENTED INSTALLATION:
Go to STEP 4 on page 12.
ROOF-VENTED INSTALLATION:
1. Remove and save the two blower screws, See Figure 11.
2. Carefully lift the blower unit out of the microwave oven,
slipping wires out of clips.
3. Rotate blower unit end over end. Rotate the unit 90°so
that the exhaust ports face the upper of the unit. See
Figure 12. Slip wires into clips at the bottom left hand
corner of blower unit. See Figure 13.
4. Place blower unit back into cabinet. Check that the exhaust
ports face the upper of the cabinet. See Figure 14.
5. Tighten the two blower screws. See Figure 14.
NOTE: If you want to install this microwave oven properly,
you should be careful to tighten the blower screws.
For a roof-vented installation, use the screw holes
labeled “A”in figure 18 on page 11.
STEP 3:
PREPARE THE VENTING BLOWER
blower
screw
exhaust ports
Figure 11
Figure 12
blower
unit
Figure 10
Figure 10-1
blower
screw
blower
unit
exhaust
ports
Figure 14
exhaust ports
Figure 13
wire clips
W A R N I N G
–10 –
Otros manuales para DOTRC11B
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Microondas de Dometic
Dometic
Dometic CDMWIOMW Manual de usuario
Dometic
Dometic DOTR12CWl Manual de usuario
Dometic
Dometic MWO24 Manual de usuario
Dometic
Dometic DCMC11B.F Manual de usuario
Dometic
Dometic CDMW10MW Manual de usuario
Dometic
Dometic MWO240 Manual de usuario
Dometic
Dometic DOTRC11SS Manual de usuario
Dometic
Dometic DOTRM15S Manual de usuario
Dometic
Dometic DOTRC17BC Manual de usuario
Dometic
Dometic C2286.000 Manual de uso y cuidado
Dometic
Dometic 56-1413 Manual de usuario
Dometic
Dometic DOTR12CBIV Manual de usuario
Dometic
Dometic DMW14MW Manual de usuario
Dometic
Dometic DOTRC11SS Manual de usuario
Dometic
Dometic DMW10W Manual de usuario
Dometic
Dometic MWO240 Manual de usuario
Dometic
Dometic CDMW07B Manual de usuario
Dometic
Dometic DMT113U1B Manual de usuario
Dometic
Dometic DMW10MW Manual de usuario
Dometic
Dometic DOTRM15S Manual de usuario
