DNF Controls ST600-KIPRO Manual de usuario

ST600-KIPRO User Manual

Page 1of 16

ST600-KIPRO

User Manual

ST600-KIPRO User Manual

Page 2of 16

TABLE OF CONTENTS

GETTING STARTED............................................................................................... 3

EQUIPMENT LIST................................................................................................. 3

INSTALLATION..................................................................................................... 4

SYSTEM CONFIGURATION WEB PAGE .................................................................. 5

CONNECTION TO AJA KI-PRO.................................................................................. 7

OPERATION ........................................................................................................ 8

CLIP LIST WEB PAGE ...........................................................................................10

8. FUNCTION TABLE ...............................................................................................11

9. KEY LAYOUT.......................................................................................................13

10.SPECIFICATIONS .................................................................................................14

11 DNF CONTROLS LIMITED WARRANTY..................................................................16

REVISIONS

1.00

01/24/17

Original draft.

ST600-KIPRO User Manual

Page 3of 16

NOTE: KiPro Rack does not support Search to Time or Shuttle or Slomo functionality.

KiPro Ultra does not support Shuttle or Slomo functionality.

1. GETTING STARTED

1. Go to Installation Section to set up ST600.

2. Go to System Configuration Section to set static IP address, Subnet Mask, and

Gateway address.

3. Go to Remote Device Assignment Section to enter IP addresses for remote devices that

ST600 will communicate with.

4. Go to System Configuration section to set default settings.

2. EQUIPMENT LIST

Qty

Component

DNF Part Number

ST600 Panel

ST600-KIPRO

ST600 POWER SUPPLY

included

POWER CORD

included

ST600-KIPRO User Manual

Page 4of 16

3. INSTALLATION

1. Connect supplied power supply to POWER connector

2. Connect Ethernet cable to ETHERNET connector.

Rear View

DEFAULT ETHERNET CONFIGURATION

IP Address:

192.168.10.217

Subnet Mask:

255.255.255.0

Gateway:

192.168.10.1

The ST600 is configured using a standard web browser (Internet Explorer, Firefox, and Chrome).

Enter the IP address in the Address/ URL bar, typically located at the top of the web browser

page, to access the Home Page. Use the links on the left side of the Home Page to access the

desired configuration web pages.

All configuration settings are saved in non-volatile memory in the ST600. Settings are retained

when power is removed.

Settings may be uploaded to a computer as a configuration file (.dnf) for storage. Configuration

files may be downloaded from a computer into the ST600 to restore a saved configuration. A

configuration file contains all of the ST600’s configurations except IP address, subnet mask, and

gateway address. The ST600 does not support partial configuration upload or download. The

configuration file is a not a text formatted file. It cannot be viewed or modified with a text

editor.

To access the System Configuration web page, use the following log-on when prompted:

Username: dnfuser

Password: controls

ST600-KIPRO User Manual

Page 5of 16

4. SYSTEM CONFIGURATION WEB PAGE

SELECTION

DESCRIPTION

P1 Software Upgrade:

Use this link to install the P1 upgrade file provided by DNF Controls

P2 Software Upgrade:

Use this link to install the P2 upgrade file provided by DNF Controls

Web Upgrade:

Use this link to install the Web pages upgrade file provided by DNF

Controls

Save Configuration to PC:

Use this link to save the ST600 current configuration to a

configuration file on

a computer. The web browser will prompt for

file name and directory. The file

extension must be ‘dnf’.

ST600-KIPRO User Manual

Page 6of 16

SELECTION

DESCRIPTION

Restore Configuration from PC:

Use this link to download a configuration file from your computer to

the ST600.

The web browser will prompt for directory and

configuration file name. The file

extension must be ‘dnf’.

Set Factory Defaults:

Use this link to reset all ST600 configuration settings to factory

defaults. This

will NOT change the IP address, subnet mask or

gateway address. The ST600

will automatically reboot.

Enter Label:

Enter label to be displayed on top right of all web pages

Enter the new IP settings below:

Enter the new IP address, Gateway, and Subnet Mask. Click on “Save

Config”to

save the new entries. The ST600 will automatically

reboot.

ST600-KIPRO User Manual

Page 7of 16

5. CONNECTION TO KI PRO

1. Using a Web browser, enter the IP address of the ST600-Kipro panel to access the

configuration pages.

2. Select the Remote Device Assignment link located on the left hand side of the web

page.

3. In the Remote Device Assignment page, create a device label for the AJA KIPRO you

will be connecting to.

4. In the “Device type” column, select “KIPRO” from the dropdown menu.

5. In the “Connection type” column, select “TCP” from the dropdown

6. In the “Connection Mode” column, select “Client Transmit/Receive”

from the dropdown menu.

7. In the “IP Address” column, enter the IP address of the Ki Pro. Next

under “Port Number” set the Port number to “80”.

8. Press “Save” to save your changes.

The ST600-KiPro communicates over IP to AJA KiPros using the KiPros's native control

protocol. The native control protocol does not provide a means to synchronously roll multiple

units. As a result, transport commands are sent to each KiPro, one at a time. There will be a

delay between KiPros based upon inherent IP network delays and each KiPro's command

processing delay after receiving the command.

ST600-KIPRO User Manual

Page 8of 16

6. OPERATION

LCD DISPLAY

During normal operation, the top row of the display shows the selected time mode

and current time location of the selected Ki Pro.

For example: 01:12:09:23

Second Row shows name of loaded clip

For example: Clip: SC1TK47

TRANSPORT CONTROL

Select the desired transport function by pressing the appropriate key. The Real-Time

Status Indicators will light to indicate the DDR's current transport mode.

See Function Table (Pg 12) for a full list of functions and a description of each function.

CREATE AND RECORD CLIP FROM WEB PAGE

1. Using a Web browser, enter the IP address of the ST600-Kipro panel to access the

configuration pages.

2. Select the Clip List link located on the left hand side of the web page.

3. In the Clip list page, create a new clip in the following window:

4. Press the “Create and Record” button to create the desired clip and to begin the

recording.

LOAD CLIP FROM WEB PAGE

1. Using a Web browser, enter the IP address of the ST600-Kipro panel to access the

configuration pages.

2. Select the Clip List link located on the left hand side of the web page.

3. In the Clip list page, select the desired clip to load and select the LOAD button under

the Load Clip column.

Your clip will now be loaded and ready to play.

ST600-KIPRO User Manual

Page 9of 16

LOAD A CLIP FROM ST600-KIPRO

1. Press [SHIFT/ESC] + [LOAD] to set the ST600-KiPRO into a “LOAD” mode.

2. Once in “LOAD”mode, use numeric keys 0-9 of the panel (yellow silkscreen) to call

up the desired clip number

3. After the numeric clip ID is entered, Press [LOAD] key to execute the load.

Your clip will now be loaded and ready to play.

CUE POINTS

1. Press the [MARK] key to mark the Ki Pro’s current time into the selected cue point #.

2. Use [↑] or [↓] to step through marked cue points.

3. Press the [LOAD] key to load the currently selected cue point.

ST600-KIPRO User Manual

Page 10 of 16

CLIP LIST WEB PAGE

Load Clip For Play

Choose from the list of Clips and simply press “LOAD”.

Clip will load and show time and name of loaded clip on ST600 LCD

display.

Create Clip for

Record

Type in name you wish to create for your clip and click on “Create &

Record” on ST600 Clip List web page to create the desired clip.

*Record will start once “Create & Record” is pressed on web page

or when

Record key is pressed on the ST600

Tabla de contenidos

Otros manuales de Controladores de DNF Controls

DNF Controls

DNF Controls 4000CL-L Manual de usuario

DNF Controls

DNF Controls ST30 Manual de usuario

DNF Controls

DNF Controls ST100 Manual de usuario

DNF Controls

DNF Controls ST300-SSM Manual de usuario

DNF Controls

DNF Controls DMAT-MAV Manual de usuario

DNF Controls

DNF Controls 4000CL-O Manual de usuario

DNF Controls

DNF Controls RPC-HOR-PESA Manual de usuario

DNF Controls

DNF Controls TBC-2-DVC Manual de usuario

DNF Controls

DNF Controls 2044CL-EVS Manual de usuario

DNF Controls

DNF Controls 2MCE-24P Manual de instalación y operación

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario