DMX4ALL DMX-Servo-Control 2 Manual de usuario

DMX-Servo-Control 2

User Manual

DMX-Servo-Control 2 2

For your own safety, please read this user manual and warnings carefully

before installation.

Description

The DMX-Servo-Control 2 is designed for controlling of two servos via DMX.

Two Servos

The DMX Servo Control 2 has two servo ports. Each can be controlled via one DMX

channel.

Servos with 5V up to 12V DC can be used

The supply voltage of the DMX-Servo-Control 2 is between 5V and 12V.

Servos with a supply voltage within this range can be connected directly.

Adjustable Servo control signal

The controlling occurs via an adjustable pulse width.

Compact Design

The design and the compact construction allows an installation of this small

assembly in areas that do not offer much space.

LED-Display

The integrated LED is a multifunctional display for showing the current device status.

DMX Addressing

The DMX addressing is settable via a 10-position DIP switch.

RDM Support

The DMX Servo Control 2 allows configuration via RDM over DMX.

DMX-Servo-Control 2 3

Data sheet

Power supply: 5-12V DC

50mA without connected servo

Protocol: DMX512

RDM

Servo-Voltage: 5-12V DC (corresponds to the supply voltage)

Servo-Power: max. 3A in sum for both servos

DMX-Channels: 2 Channels

Connection: 1x screw terminal / 2pin

1x screw terminal / 3pin

2x pin header RM2,54 / 3pin

Dimension: 30mm x 67mm

Content

1x DMX-Servo-Control 2

1x Quick manual german and english

DMX-Servo-Control 2 4

Connection

ATTENTION :

This DMX-Servo-Control 2 is NOT ADMITTED for applications whom has

safety-relevant requirements or in which dangerous situations can occur !

DMX-Servo-Control 2 5

LED-Display

The integrated LED is a multifunction display.

During to the normal operation mode the LED lights permanently. In this case the

device is working.

Furthermore, the LED shows the current status. In this case the LED lights up in

short pitches and then is missing for longer time.

The number of the flashing lights is equal to the event number:

Status

Number

Error

Description

1 No DMX There is no DMX-Address

2 Addressing

error

Please check, if a valid DMX-Start Address

is adjusted via the DIP-Switches

4 Configuration

stored

The adjusted configuration is stored

DMX-Servo-Control 2 6

DMX-Addressing

The Start Address is adjustable via DIP-Switches.

Switch 1 has the valency 2

(=1), switch 2 the valency 2

(=2) and so on up to

switch9 with the valency 2

(=256).

The sum of the switches showing ON is equal to the start address.

Address

Switch Address

Switch

OFF

12345678910

... ...

OFF

12345678910

508

OFF

12345678910

OFF

12345678910

509

OFF

12345678910

OFF

12345678910

510

OFF

12345678910

OFF

12345678910

511

OFF

12345678910

The DMX start address can be also adjusted via the RDM parameter

DMX_STARTADDRESS. For RDM operation all switches must be set to OFF !

DMX-Servo-Control 2 7

Servo control signal

The signal which is send to the Servo consists of a High-Impulse and a Low one. The

pulse duration is important for the Servo.

Normally this impulse is between 1ms and 2ms, which is also the standard setting for

the DMX-Servo-Control 2. These are the end positions of the Servos where it is not

limited mechanically. A pulse length of 1.5ms would be the Servo middle position.

1,5ms

2ms (max)

1ms (min)

→Servo is positioned left

→Servo is positioned right

→Servo is positioned centred

DMX-Servo-Control 2 8

Adjust Servo control signal

In according to the used Servo it can be advantageous to adapt the impulse-times.

The minimum time for the left position can be set within the range 0,1-2,5ms. The

maximum time for the right position must be bigger than the minimum time and can

be maximum 2,54ms.

Please proceed as following for the settings:

-Turn on the DMX-Servo-Control

-Set DIP-Switch 9 and 10 on OFF

-Set DIP-Switch 10 on ON

-Set via the DIP-Switched 1-8 the Minimum time

-Set DIP-Switch 9 on ON

-Set via the DIP-Switched 1-8 the Maximum time

-Set DIP-Switch 10 on OFF

-The LED lights up 4x as confirmation that the settings are stored

-Set via DIP-Switches 1-9 the DMX-Starting address

The time-setting takes place with the DMX-Addressing via the DIP-Switches in 10µs

steps. Thereby the set value with 0,01ms is multiplied, so for example a value of 100

results in a value of 1ms.

1,00ms

= 100 x 0,01ms

2,52ms

= 252 x 0,01ms

1,01ms

= 101 x 0,01ms

2,53ms

= 253 x 0,01ms

1,02ms

= 102 x 0,01ms

2,54ms

= 254 x 0,01ms

The RDM parameters LEFT_ADJUST and RIGHT_ADJUST can also be used

to set the pulse time.

DMX-Servo-Control 2 9

RDM

(from Hardware V2.1)

RDM is the short form for Remote Device Management.

As soon as the device is within the system, device-dependent settings occur remotely

via RDM command due to the uniquely assigned UID. A direct access to the device is

not necessary.

If the DMX start address is set via RDM, all address switches at the DMX-

Servo-Control 2 must be set to OFF ! A DMX start address set by the address

switches is always prior !

This device supports the following RDM commands:

Parameter ID

Discovery

Command

SET

Command

GET

Command

ANSI/

PID

DISC_UNIQUE_BRANCH



E1.20

DISC_MUTE



E1.20

DISC_UN_MUTE



E1.20

DEVICE_INFO



E1.20

SUPPORTED_PARAMETERS



E1.20

PARAMETER_DESCRIPTION



E1.20

SOFTWARE_VERSION_LABEL



E1.20

DMX_START_ADDRESS



E1.20

DEVICE_LABEL



E1.20

MANUFACTURER_LABEL



E1.20

DEVICE_MODEL_DESCRIPTION



E1.20

IDENTIFY_DEVICE



E1.20

FACTORY_DEFAULTS



E1.20

DMX_PERSONALITY



E1.20

DMX_PERSONALITY_DESCRIPTION



E1.20

DISPLAY_LEVEL



E1.20

DMX_FAIL_MODE



E1.37

DMX-Servo-Control 2 10

Parameter ID

Discovery

Command

GET

Command

ANSI/

PID

SERIAL_NUMBER



PID:

0xD400

LEFT_ADJUST



PID:

0xD450

RIGHT_ADJUST



PID:

0xD451

1) Manufacturer depending RDM control commands (MSC - Manufacturer Specific Type)

Manufacturer depending RDM control commands

SERIAL_NUMBER

PID: 0xD400

Outputs a text description (ASCII-Text) of the device serial number.

GET Send: PDL=0

Receive: PDL=21 (21 Byte ASCII-Text)

LEFT_ADJUST

PID: 0xD450

Sets the high time length for left servo position.

GET Send: PDL=0

Receive: PDL=2 (1 Word LEFT_ADJUST_TIME)

SET Send: PDL=2 (1 Word LEFT_ADJUST_TIME)

Receive: PDL=0

LEFT_ADJUST_TIME

Fun

tion

200 - 5999 WERT x 0,5µs = Impulszeit LINKS

Default: 2000 (1ms)

RIGHT_ADJUST

PID: 0xD451

Sets the high time length for right servo position.

GET Send: PDL=0

Receive: PDL=2 (1 Word RIGHT_ADJUST_TIME)

SET Send: PDL=2 (1 Word RIGHT_ADJUST_TIME)

Receive: PDL=0

LEFT_ADJUST_TIME

Fun

tion

201 - 6000 WERT x 0,5µs = Impulszeit RECHTS

Default: 4000 (2ms)

Tabla de contenidos

Otros manuales de Hardware de computadora de DMX4ALL

DMX4ALL

DMX4ALL WirelessDMX RX board Manual de usuario

DMX4ALL

DMX4ALL ArtNet-DMX TWIN PoE Manual de usuario

DMX4ALL

DMX4ALL DMX-Player L Manual de usuario

DMX4ALL

DMX4ALL MaxiRGB Manual de usuario

DMX4ALL

DMX4ALL DMX-Universal-Demux Manual de usuario

DMX4ALL

DMX4ALL DMX-Relais 2 INRUSH Manual de usuario

DMX4ALL

DMX4ALL ArtNet-DMX Mux24 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario