DMP Electronics 1106 Manual de usuario

1106 WIRELESS UNIVERSAL

TRANSMITTER

Installation Guide

The 1106 Wireless Universal

Transmitter is a wireless, two-input

transmitter typically used for door

and window applications.

The 1106 provides a cover tamper,

magnetic reed switch, and an

on-board terminal block to allow for

external contact wiring.

Both sets of contacts, internal and

external, can be programmed to

operate at the same time. This

allows two independent zones to

operate from one 1106.

The 1106 also features

Disarm/Disable functionality. When

this option is set to YES, Zone

Tripped messages are disabled

when the system is disarmed to

allow for extended transmitter

battery life. Supervision, Tamper,

and Low Battery are the only

messages that are sent to the panel

when the system is disarmed.

Compatibility

All DMP XTLplusTM, XT30/XT50, and

XR150/XR550 Series panels and all

1100 Series Wireless Receivers.

What is Included?

• One 1106 Wireless Universal

Transmitter

• One magnet in a one or

two-part housing

• One 3.0V lithium CR123A battery

• Hardware pack

• Double-sided tape

1PROGRAM THE PANEL

Refer to the panel programming guide as needed.

1. In ZONE INFORMATION, enter the wireless ZONE NO: and

press CMD.

2. Enter the ZONE NAME and press CMD.

3. Select the ZONE TYPE and press CMD.

4. At the NEXT ZN? prompt, select NO.

5. Select YES when WIRELESS? displays.

6. Enter the eight-digit SERIAL# and press CMD.

7. At CONTACT, select either INTERNAL or EXTERNAL.

Note: Use consecutive zone numbers if using both internal

and external contacts.

8. If EXTERNAL was chosen in Step 7, choose NO or YES at

the NORM OPEN prompt.

9. Enter the SUPRVSN TIME and press CMD.

10. At DISARM DISABLE, select NO or YES.

11. At the NEXT ZN? prompt, select YES to ﬁnish programming

or select NO for additional programming options.

Figure 1: 1106 Housing

INSTALL THE BATTERY

Use a 3.0V lithium battery, a DMP Model CR123 battery, or an

equivalent model from Sony or Murata. For listed installations, use

either an Energizer® 123 battery or a CR123A battery manufactured

by Panasonic or Tekcell. Keep in mind, when setting up a wireless

system, program zones and connect the wireless receiver before

installing the battery.

1. Open the 1106 by inserting a 1/4” ﬂat head screwdriver in

the tab. See Figure 1.

2. Gently pull upwards on the screwdriver handle until the

housing completely opens.

3. Observe polarity and place the battery in the holder and

press it into place.

3The 1106 provides a Survey LED capability to allow one person to

conﬁrm communication with the wireless receiver or panel while

the cover is removed.

1. Hold the 1106 in the exact desired location.

2. Press the tamper switch to send data to the panel and

determine if communication is conﬁrmed or faulty.

Conﬁrmed: If communication is conﬁrmed, for each

press or release of the tamper switch the LED blinks

immediately on and immediately o.

Faulty: If communication is faulty, the LED remains on

for about 8 seconds or ﬂashes multiple times in quick

succession. Relocate the 1106 or wireless receiver until

the LED conﬁrms clear communication.

SELECT A LOCATION

Tab

DESCRIPTION

2 1106 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS

MOUNT THE 1106

For UL listed and commercial installations, use the supplied

screws when mounting the transmitter and the magnet.

Mount the Transmitter

1. If mounting with screws, remove the battery. If mounting

with double-sided tape, place the tape on the back of the

transmitter.

2. Hold the transmitter in place with the magnetic reed

switch closest to where the magnet will be mounted. See

Figure 2. Ensure the transmitter and the magnet will be no

more than 1/2” (1.3cm) apart.

3. If using screws, place the supplied #4 screws into the two

mounting holes and secure the transmitter to the surface.

If using double-sided tape, place the transmitter on the

surface.

4. Snap the transmitter cover back onto the base.

Mount the Magnet

Standard Installation

1. Push the supplied magnet into the magnet cover.

2. Hold the magnet base on the door closest to the

magnetic reed switch, no more than 1.3cm (0.5in) from the

transmitter.

3. If using screws, use the provided #4 screws to mount the

base. See Figure 3. If using double-sided tape, place the

tape on the back of the base and place on the surface.

4. Snap the cover onto the base.

Commercial Installation

1. Push the supplied magnet into the magnet cover.

2. Place and hold the magnet cover directly on the door

closest to the magnetic reed switch, no more than 1.3cm

(1.5in) apart from the transmitter.

3. Use the provided #4 screws to mount the cover.

See Figure 4.

5TEST THE 1106

After installing the 1106, perform a Walk Test to conﬁrm the 1106 is communicating with the panel.

At the keypad, enter 8144 (WALK) and select WLS. If the 1106 fails to check in at the keypad, relocate the

wireless device, receiver, or panel.

Figure 3: Standard Installation

Figure 4: Commercial Installation

Wall Mount

Screw Holes

Magnetic Reed

Switch

Figure 2: Transmitter Components

1106 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 3

Connect External Contacts

Refer to Contacts and Zone Information in the appropriate panel programming guide for more information. DMP

recommends using 18 or 22 AWG un-shielded wire. If you use both the magnet reed switch in the 1106 transmitter

and an external contact, use consecutive zone numbers when connecting them to the panel.

1. Remove the cover of the 1106.

2. Use a ﬂat head screwdriver to loosen the two screws on the 1106 terminal block. See Figure 5.

3. Insert the external contact wiring into the 1106 terminal block and tighten the screws.

4. Depending on how the contact was programmed in the Program the Panel section, connect the other ends of

the wires to the external contact as either normally open (N/O) or normally closed (N/C) without an end-of-

line resistor.

Figure 5: Connect External Contact

MODEL 1106

CR123

External Contact

Terminal Block

1106

Door

Window

External

Contact

ADDITIONAL INFORMATION

1. Open the transmitter housing to expose the inside of the 1106. See Figure 1.

2. Remove the old battery, observe polarity, and place the new battery in the holder.

3. Snap the cover back on the 1106.

Replace the Battery

Once the battery is replaced, a sensor reset is required at the keypad to clear the LOBAT message.

1. On an LCD Keypad, press and hold 2for two seconds. On a Graphic Touchscreen Keypad,

press RESET.

2. Enter your user code, if required. The keypad displays SENSORS OFF followed by SENSORS

ON.

Sensor Reset to Clear LOBAT

Magnet

Program one

zone as an

internal contact. Program the next

consecutive zone as

an internal contact.

EXTERNAL CONTACTS

Designed, engineered,

and manufactured in

Springﬁeld, Missouri using U.S.

and global components.

LT-1377 1.01 18102

INTRUSION • FIRE • ACCESS • NETWORKS

2500 North Partnership Boulevard

Springﬁeld, Missouri 65803-8877

866.266.2826 | DMP.com

FCC INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from

all persons. It must not be located or operated in conjunction with any other antenna or transmitter.

Changes or modiﬁcations made by the user and not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment o and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

INDUSTRY CANADA INFORMATION

This device complies with Industry Canada Licence-exempt RSS standard(s). Operation is subject to the following two

conditions:

1. This device may not cause interference, and

2. this device must accept any interference, including interference that may cause undesired operation of the device.

This system has been evaluated for RF Exposure per RSS-102 and is in compliance with the limits speciﬁed by Health

Canada Safety Code 6. The system must be installed at a minimum separation distance from the antenna to a general

bystander of 7.87 inches (20 cm) to maintain compliance with the General Population limits.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes:

1. l’appareil ne doit pas produire de brouillage, et

2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d’en compromettre le fonctionnement.

L’exposition aux radiofréquences de ce système a été évaluée selon la norme RSS-102 et est jugée conforme aux limites

établies par le Code de sécurité 6 de Santé Canada. Le système doit être installé à une distance minimale de 7.87 pouces

(20 cm) séparant l’antenne d’une personne présente en conformité avec les limites permises d’exposition du grand

public.

Patents

U. S. Patent No. 7,239,236

Certiﬁcations

FCC Part 15 Registration ID: CCKPC0124

Industry Canada: 5251A-PC0124

Underwriters Laboratory (UL) Listed

• ANSI/UL 1023 Household Burglar Alarm System

• ANSI/UL 634 Connections and Switches for use with Burglar Alarm

Systems Accessory

Universal Speciﬁcations

Do not use double-sided tape for listed installations.

Household Burglar Alarm System Units ANSI/UL 1023

Install only on non-conductive surfaces.

1106 Wireless Universal

Transmitter

Speciﬁcations

Battery

Life Expectancy 5 years (normal operation)

Type 3.0V lithium CR123A

Frequency Range 905-924 MHz

Color White

Housing Material Flame retardant ABS

Dimensions

Transmitter Case 1.79”L x 1.69”W x 0.84”H

Standard

Magnet Housing

1.35”L x 0.38”W x 0.43”H

Commercial Magnet Housing 2.25”L x 0.38”W x 0.34”H

Tabla de contenidos

Otros manuales de Transmisor de DMP Electronics

DMP Electronics

DMP Electronics 1103INT Manual de usuario

DMP Electronics

DMP Electronics 1140 Series Manual de usuario

DMP Electronics

DMP Electronics 1103 Series Manual de usuario

DMP Electronics

DMP Electronics 1142 Series Manual de usuario

DMP Electronics

DMP Electronics 1142INT Manual de usuario

DMP Electronics

DMP Electronics 1106-WINT Manual de usuario

DMP Electronics

DMP Electronics 1102 Manual de usuario

DMP Electronics

DMP Electronics 1101-WINT Manual de usuario

DMP Electronics

DMP Electronics 1139 Manual de usuario

DMP Electronics

DMP Electronics 1100 Series Manual de usuario

DMP Electronics

DMP Electronics 1101 Manual de usuario

DMP Electronics

DMP Electronics 1144 Series Manual de usuario

DMP Electronics

DMP Electronics 1103 Series Manual de usuario

DMP Electronics

DMP Electronics 1100INT Series Manual de usuario

DMP Electronics

DMP Electronics 1107 Manual de usuario

DMP Electronics

DMP Electronics 1101 Manual de usuario

DMP Electronics

DMP Electronics 1101 Series Manual de usuario

DMP Electronics

DMP Electronics 1141 Manual de usuario

DMP Electronics

DMP Electronics SecuraHub Series Guía de instalación

DMP Electronics

DMP Electronics 1103INT Manual de usuario

DMP Electronics

DMP Electronics 1144INT Series Manual de usuario

DMP Electronics

DMP Electronics 1102 Manual de usuario

DMP Electronics

DMP Electronics 1139 Manual de usuario

DMP Electronics

DMP Electronics 1101 Series Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario