Dixon ZTR 312 Manual de instrucciones

TECHNICAL, DATA

ZTR MODEL, 312

IMPORTANT -READ OPERATOR'S MANUAL BEFORE OPERATING OR MAKING ADJUSTMENTS

SEAT ADJUSTMENT

1. Pull or lift body retention latch (P/N 3934)

from transaxle backing plate, raise and push

body and seat assembly forward.

2. Loosen four seat ad jus tee/it knobs (P/N 1849)

and slide seat forward or backward to desired

position.

3. Re-tighten seat adjustment knobs (P/N 1849). DO

NOT operate Bower without seat adjustment knobs

properly tightened.

4. Close upper body and push retention

latch (P/N 3934) over transaxle backing plate.

REMOVING THE BODY

1. The 312 has a (2) piece polyethelene body. The upper body can be folded forward

to expose the transaxle. In some cases, it nay be necessary to remove the

upper body to service the transaxle.

2. To relieve upper body, remove two bolts (P/N 3080) from the front of upper

body hinge located on the brake shaft (P/N 9283). Disconnect seat switch

(P/N 4761) at plug-in.

3. Reverse above procedure to reinstall.

ADJUSTMENT OF MOWER DECK DRIVE BELT

1. This mower deck drive belt is tensioned by a spring loaded engagement idler

quadrant.

2. This system is designed to maintain the proper belt tension at all times.

3. Belt tension can be adjusted by moving the engaging rod (P/N 7013) into the

outside hole of engagement handle (P/N 7020).

4. After belt tension is adjusted, check to assure that the mower blade will

not turn freely when the engaging rod is in the "OFF" positon.

5. If the mower blade turns freely, adjust the blade brake by loosening nut (P/N

3205) at the end of the brake rod (P/N 2988).

6. After adjustment is achieved, perform the safety checks listed below.

Page 1 of 7

DIXON INDUSTRIES, INC

A BLOUNT COMPANY

AIRPORT INDUSTRIAL PARK

PO BOX 1569

COFFEYVILLE KS 67337 O945

316 251 20OO

FAX 316 251 4117

REMOVING THE MOWER BLADE

Secure blade (P/N 2483) from turning. Remove blade bolt from center of

blade (P/N 3268), and blade washer (P/N 6260) then remove blade (P/N 2483). To

reinstall, reverse above procedure.

WARNING: Sharp edges on blade can cause Injury! Caution should be exercised when

service is required on blade.

REMOVING THE MOWER DECK

1. Loosen belt keeper (P/N 7026 & 7027) located under the engine, by loosening two

rear engine mounting bolts, allowing the deck drive belt to come free of the rear

pulley.

2. Disconnect the wiring loom at the deck safety switch (P/N 4242).

3. Remove the two clevis pins (P/N 3072) from the two rear L-rods (P/N 1355) and

slide from slots.

4. Remove clevis pin (P/N 3072) from L-rod attached to lift handle and slide from

slot.

5. Remove clevis pin (P/N 3072) from front deck hanger shaft (P/N 1332), located at

front of mower deck on slide plates welded at battery box, and remove.

6. Lift front of mower chassis clear of deck. Roll chassis free of the deck.

7. To Install, reverse the above procedure.

MOWER BLADE OPERATION

To engage mower blades, turn engagement lever on floor slowly to the "ON"

position. To disengage mower blades, turn lever slowly to the "OFF" position.

"IMPORTANT" -PERFORM SAFETY CHECKS AFTER MAKING ANY REPAIRS OR ADJUSTMENTS

1. After reassembly, while seated on mower, attempt to start engine with mower deck

engaged. Engine should not start. If engine does start, return the mower to an

Authorized Dixon Dealer for adjustment or repair.

2. Disengage mower deck and start engine. With the operator in the normal seated

position, engage mower deck and remove weight from seat. The engine should stop.

If the engine doesn't stop when operator rises from the seat, return the mower to

an Authorized Dixon Dealer for adjustment or repair.

3. Engage, then disengage, mower blade in each cutting height. Insure that blade

disengages and comes to a stop within (5) seconds In each height position.

If blade does not disengage properly, contact your Authorized Dixon Dealer.

PARKING BRAKE ADJUSTMENT

Remove the body as described above. Tighten nut on brake rod (P/N 2533)

located in front of the transaxle on each side, just enough to prevent brake

from slipping when engaged.

CAUTION: Over tightening may cause premature wear on the brake band (P/N 5085).

Page 2 of 7

Revised 1/92

(P/N 8114)

Tabla de contenidos

Otros manuales de Cortacésped de Dixon

Dixon

Dixon ZTR 4423 Manual de usuario

Dixon

Dixon ZTR 6000 Series Manual de usuario

Dixon

Dixon ZTR RAM SERIES Manual de instalación

Dixon

Dixon 312 Manual de instrucciones

Dixon

Dixon 12881-106 Manual de operación y mantenimiento

Dixon

Dixon SpeedZTR 30 CE Manual de usuario

Dixon

Dixon ZTR 7525 Manual de usuario

Dixon

Dixon SPEEDZTR 30 Guía

Dixon

Dixon BLOUNT 3301 Manual de instrucciones

Dixon

Dixon ZTR 5000 Series Manual de usuario

Dixon

Dixon D25KH48 Manual de usuario

Dixon

Dixon ZTR 424 Manual de instrucciones

Dixon

Dixon ZTR 8000G Series Manual de usuario

Dixon

Dixon ZTR 1001 Manual de usuario

Dixon

Dixon ZTR 3000 Series Manual de usuario

Dixon

Dixon SPEEDZTR 44/965981001 Manual de usuario

Dixon

Dixon ZTR 502 Manual de usuario

Dixon

Dixon ZTR RAM SERIES Guía

Dixon

Dixon PERSONAL LIFT 3302 Manual de instrucciones

Dixon

Dixon ZTR 1950-2300 Series Manual de usuario

Dixon

Dixon ZTR 503 Manual de usuario

Dixon

Dixon ZTR 7500 series Manual de usuario

Dixon

Dixon D26KH54 Manual de usuario

Dixon

Dixon 2004 Manual de usuario

Manuales populares de Cortacésped de otras marcas

RHINO

RHINO 1958 Manual de usuario

Wolf Garten

Wolf Garten Compact plus 40 B Manual de usuario

Cub Cadet

Cub Cadet LTX 1045 Manual de usuario

Craftsman

Craftsman 917.378461 Manual de usuario

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manual de usuario

Challenge

Challenge CH18V2 Instrucciones de operación

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manual de usuario

DEWEZE

DEWEZE ATM-725 Manual de operación

Weed Eater

Weed Eater 180083 Manual de usuario

Husqvarna

Husqvarna Poulan Pro PP185A42 Manual de usuario

Better Outdoor Products

Better Outdoor Products Quick Series Manual de usuario

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manual de funcionamiento

MTD

MTD 795, 792, 791, 790 Manual de usuario

Toro

Toro Groundsmaster 3505-D Manual de usuario

Dennis

Dennis FT 610 Manual de usuario

AIRFORCE

AIRFORCE F-15 Gen 3 Manual de usuario

MTD

MTD 126-220-000 Manual de usuario

Toro

Toro 74806 Manual de usuario