Discovery Telecom ESIM002 Manual de usuario

ESIM022

GSM DIALLER

Тел: +7 495 7907870

Моб: +7 965 4429948

Skype: Discoverytelecom

Mail: [email protected]

www.discoverytelecom.ru

2EN ESIM022 User manual v1.1

User Manual v1.1

SAFETY INSTRUCTIONS

Please read and follow these safety guidelines to safeguard yourself and others:

• GSM dialler ESIM022 (later referred to as “the system” or “the device”) contains a built-in

radio transceiver operating in GSM 900/1800 MHz bands.

• DO NOT use the system where it can cause potential danger and interfere with other

devices – such as medical devices.

• DO NOT use the system in hazardous environment.

• DO NOT expose the system to high humidity, chemical environment or mechanical impact.

• DO NOT attempt to repair the system yourself – any repairs must be carried out by fully

qualied personnel only.

Please, use the 12-15 V 300 mA DC power supply unit that meets the EN

60950-1 standard. Any additional device you connect to the system, such as a

computer, must also be powered by an EN 60950-1 approved supply. When con-

necting the power supply to the system, mind the polarity terminals. DO NOT

switch the polarity terminals places.

External power supply must be reachable

and can be connected to AC mains only

inside installation room with automatic

2-pole circuit breaker capable of discon-

necting circuit in the event of short circuit or

over-current condition. Open circuit breaker

must have a gap between connections of

more than 3 mm and the disconnection cur-

rent 5 A.

Phase

DC 12-15 V

Null

ESIM022

USB cable

Disconnect the mains power before installing. Never install or carry out mainte-

nance during stormy weather. The electric socket that powers the system must be

easily accessible. In case of power cut, the system is powered by a back-up battery

(if any).

WARNING: Only use the approved 8.4V 250mAh rechargeable Ni-Mh 6HR61

(IEC)/7.2H5 (ANSI/NEDA) back-up battery with the system to avoid re or explo-

sion. Take care when connecting positive and negative battery terminals.

ESIM022 User manual v1.1

To switch the system o, unplug the external electric power supply, disconnect

the back-up battery or any other linked device that the system is powered from. A

blown fuse cannot be replaced by the user. The replacement fuse has to be of the

kind indicated by the manufacturer (Fuse F1 model – miniSMDC 0,5A).

If you use a computer for the device conguration, it must earthed.

The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see right) or its

documentation indicates that the product must not be disposed of together with household waste. To

prevent possible harm to human health and/or the environment, the product must be disposed on in

an approved and environmentally safe recycling process. For further information on how to dispose of

this product correctly, contact the system supplier, or the local authority responsible for waste disposal

in your area.

4EN ESIM022 User manual v1.1

Contents

1. GENERAL INFORMATION .............................................................................................. 7

2. TECHNICAL SPECIFICATIONS ....................................................................................... 8

2.1. Electrical & Mechanical Characteristics .................................................................................... 8

2.2. Wiring Diagrams.......................................................................................................................... 10

3. INSTALLATION ............................................................................................................ 11

4. GENERAL OPERATION DESCRIPTION......................................................................... 13

5. CONFIGURATION METHODS ....................................................................................... 14

5.1. SMS Text Messages .................................................................................................................... 14

5.2. ELDES Conguration Tool.......................................................................................................... 14

6. USER PHONE NUMBERS ............................................................................................. 14

7. DATE AND TIME ........................................................................................................... 16

8. INPUTS ........................................................................................................................ 17

8.1. Input Z1 .........................................................................................................................................17

8.2. Input Z2 ........................................................................................................................................ 18

9. TAMPER ....................................................................................................................... 24

10.ALARM/RESTORE NOTIFICATIONS............................................................................ 25

11.OUTPUT ....................................................................................................................... 31

11.1. Output Name ............................................................................................................................... 31

11.2. Turning Output ON and OFF...................................................................................................... 32

12.BACKUP BATTERY AND MAINS POWER SUPPLY STATUS MONITORING ................ 33

13.SYSTEM INFORMATION. STATUS SMS ....................................................................... 37

13.1. Periodic Status SMS.................................................................................................................... 38

14.SYSTEM NOTIFICATIONS ............................................................................................ 39

15.ONBOARD TEMPERATURE SENSOR..........................................................................43

16.REMOTE LISTENING....................................................................................................44

17.TECHNICAL SUPPORT .................................................................................................46

17.1. Troubleshooting......................................................................................................................... 46

17.2. Restoring Default Parameters ................................................................................................46

17.3.Updating the Firmware via USB Cable..................................................................................... 47

18.RELATED PRODUCTS ..................................................................................................48

ESIM022 User manual v1.1

Тел: +7 495 7907870

Моб: +7 965 4429948

Skype: Discoverytelecom

Mail: [email protected]

www.discoverytelecom.ru

6EN ESIM022 User manual v1.1

Limited Liability

The buyer agrees that the system will reduce the risk of re, theft, burglary or other danger but

that it does not guarantee against the occurrence of such events.

“ELDES UAB” will not take any responsibility for the loss of personal eects, property or revenue

whilst using the system. The liability of “ELDES UAB” is limited to the value of the system

purchased.

“ELDES UAB” is not aliated with any mobile/wireless/cellular provider and is therefore not

responsible for the quality of such services.

Manufacturer Warranty

The system carries a 24-month manufacturer warranty from “ELDES UAB”.

The warranty begins the day the system is purchased by the user and the receipt must be retai-

ned as proof of purchase date. The warranty remains valid only if the system is used as intended,

following all guidelines outlined in this manual and in accordance with the operating conditions

specied.

The warranty is void if the system has been exposed to mechanical impact, chemicals, high

humidity, uids, corrosive and hazardous environments or force majeure factors.

Dear Customer,

Thank you for choosing to purchase the GSM dialler ESIM022. Your thoughtful decision will

ensure reliable solution for many years as all ELDES products are manufactured to meet

the highest standards.

We are condent that you will be completely satised with your product. However, in the

unlikely event that you do experience a problem, please contact the dealer from whom

you made your purchase.

Contents of Pack

Item Quantity

1. ESIM022 ...............................................................1

2. User manual.........................................................1

Not included:

• SIM card – we recommend you get a contract SIM, not Pay As You Go.

• Back-up battery - can be obtained from your local distributor.

• miniUSB cable - can be obtained from your local distributor.

• Temperature sensor - can be obtained from your local distributor.

• Microphone - can be obtained from your local distributor

ESIM022 User manual v1.1

1. GENERAL INFORMATION

ESIM022 is a micro-controller based device intended to receive alarm/restore events by SMS text

message or phone call and control an electrical appliance via the GSM network.

Examples of using the system:

• Notication of system events, such as arming/disarming, alarm/restore from non-GSM alarm

system.

• Non-GSM alarm system arming/disarming by SMS text message.

• Any electrical appliance control: lighting, watering, heating etc.

• Remote reboot of the “frozen” systems, such as computer network or a server.

• Notication of failure or restoration of an electronic device by SMS text message or phone call.

Main features:

• Conguration by SMS text message and PC.

• Up to 2 users for system conguration, control and acceptance of system event notications

by SMS text messages or phone calls.

• 2 inputs customizable as NC or NO.

• Input Z1 mode: digital.

• Input Z2 modes: digital or temperature sensor for 1 external temperature sensor connection.

• 1 open-collector output for electrical appliance control or non-GSM alarm system arming/

disarming (keyswitch).

• Tamper switch for system sabotage detection.

• Optional back-up battery to maintain the power for up to 12 hours and notify the user

regarding mains power loss and restore.

• Periodic self-test notication by SMS text message to user phone number.

• Customizable notication texts.

8EN ESIM022 User manual v1.1

2.TECHNICAL SPECIFICATIONS

2.1. Electrical & Mechanical Characteristics

Supply voltage.....................................................12-15 V 300 mA max

Average current used in idle state ................... 16 mA

Supported back-up battery (optional) ............8.4V 250mAh rechargeable Ni-Mh 6HR61

(IEC)/7.2H5 (ANSI/NEDA)

GSM modem frequency......................................900/1800 MHz

Number of outputs .............................................1

Output circuit.......................................................Open collector output.

Output is pulled to COM when

turned ON.

Maximum commuting output values...............30 V 200 mA

Number of inputs................................................2

Supported temperature sensor model............Maxim®/Dallas® DS18S20, DS18B20

PCB dimensions...................................................71x50x27 mm

Enclosure dimensions ........................................96x59x34 mm

Operating temperature range...........................-30…+55 °C (-35...+55 °C with limitations)

Humidity ...............................................................0-90% RH @ 0... +40 °C (non-condensing)

2.2. Main Unit, LED Indicator & Connector Functionality

Front Back

DCCOM

COM

SIM CARD

TAMPER

RESET

MIC

LED

ANT

USB

OPEN

G S M

MO DE M

BATTERY

1 2

ESIM022 User manual v1.1

Main Unit Functionality

ANT GSM antenna

FW Pins for rmware update

TAMPER Tamper switch

GSM MODEM GSM network 900/1800 MHz modem

RESET Button for restoring default settings

SIM CARD SIM card slot / holder

LED Light-emitting diode indicating system status

USB Mini USB port

MIC Microphone connector

-/+ Backup battery slots

F1 0.5A fuse

LED indication Description

OFF No power supply

Flashing every 30 ms SIM card is not present / PIN code enabled

Flashing every 0,5 sec. Searching for GSM network

Flashing every 1 sec. Connected to GSM network/system operating successfully

Connerctors Description

Z1 Digital input terminal

COM Common terminal

Z2 Digital input terminal/temperature sensor data terminal (DATA)

DC Positive power supply terminal

C1 Open-collector output terminal/temperature sensor power

supply terminal (+4V)

10 EN ESIM022 User manual v1.1

2.2. Wiring Diagrams

General wiring Temperature sensor wiring

ESIM022

Alarm system or other appliance

+12V

PGM2

PGM1

Z1 Z2 COMCOM DC C1

ESIM022

DS18S20, DS18B20

Temperature sensor

COMZ1 Z2 DC C1COM

GND

DATA

+4V

Output wiring

ESIM022

Alarm system or other appliance

+12 V

Electrical

appliance

COMZ1 Z2 DC C1COM

3 4

Tabla de contenidos

Manuales populares de Accesorios para teléfono de otras marcas

IAI

IAI CON-T Manual de usuario

BT DIVERSE 5400 Manual de usuario

Tadiran Telecom

Tadiran Telecom EMERALD ICE Manual de usuario

Musicam

Musicam FieldFone II Manual de usuario

Polycom

Polycom KIRK KIRK 4040 Hoja de especificaciones

TIPTEL

TIPTEL DECT Set 50 Manual de usuario

Panasonic

Panasonic KX-UDS124 Manual de usuario

BT BT7600 Hoja de especificaciones

Panasonic

Panasonic KX-TVP100E Manual de usuario

View

View VP-PC Manual de usuario

Baldwin Boxall

Baldwin Boxall BT8 Manual de usuario

SMC Networks

SMC Networks SMCDPCR-AP Manual de usuario

SkyLink

SkyLink SD-001 Manual de usuario

Nera

Nera ISDN Manual de usuario

MCheeta

MCheeta CT-CID803 Plus Manual de usuario

YASKAWA

YASKAWA YRC1000 Manual de usuario

Intellitouch

Intellitouch MOH-500E Manual de usuario

Viking

Viking SQRG-12 Instrucciones de uso