Directechs DS3 Manual de usuario
Designed by Installers for Installers
INSTALLATION GUIDE
DS3+ / DS4+
2005 Chrysler 300/300c. 933.CHRYSLER 7.34.195.3
© 2022 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle’s
electrical system and components.
Introduction 3
Vehicle function compatibilities 4
Pre-installation and application warnings 5
Wiring diagram 6
Locating components in the vehicle 7
Vehicle connections 8
Module programming 11
Key-Type vehicles 11
Push-to-Start (PTS) vehicles 13
Module programming for security-only installations 15
Pairing remotes 16
Connecting the module 16
8556T Temperature Sensor 16
8504D Combo Sensor 16
RF Systems 16
When used in conjunction with SmartStart 17
D2D port configuration 17
Manual transmission 18
LED diagnostics and troubleshooting 19
Soft reset 21
Hard reset 21
Tach learning procedure (not needed with Virtual Tach) 22
Initializing Virtual Tach (not needed with hardwired or data tach applications) 22
Limited lifetime consumer warranty 23
Quick reference guide 24
Contents
3933.CHRYSLER 7.34.195.3 2005 Chrysler 300/300c
©2022 VOXX•DEI LLC. All rights reserved.
Introduction
This guide provides information on the installation of the DS3/DS3+ and DS4/DS4+ modules as a digital solution. Using these modules in a
digital configuration require the module to be flashed with vehicle specific firmware. Refer to our website (www.directechs.com) and click on
the DIRECTLINK text in the header for additional information.
DS3/DS3+ and DS4/DS4+ modules provide an all-in-one solution for most modern vehicles, and include remote start, keyless entry, security,
and immobilizer bypass capabilities. T-harnesses may also be used in many applications for easy installation.
The following methods are available to configure modules:
• Web: www.directechs.com (DS3/DS3+ and DS4/DS4+)
• Desktop Application: Directlink DT (DS3/DS3+ and DS4/DS4+)
• Mobile Device: Directlink App (DS4/DS4+ only)
When Flashing via Directlink DT (Desktop app) or via the Web, an XKloader2 will be required.
To configure via Web or DirectLink DT (mobile app):
1. Disconnect the main module from any (+) 12V power source.
2. Connect the module to your computer using the XKLoader2.
3. Follow the steps in the pop-up window that will be displayed when the module is detected.
Notes:
•Flashing via web is only possible using Internet Explorer on Windows 8, 8.1, and 10.
•This method is not compatible with any other browser (Edge, Chrome, Firefox, etc.)
•When using Windows 11 or newer, Directlink DT is mandatory.
The DS4/DS4+ module is designed to be configured using the DirectLink application through mobile devices.
To download the DirectLink mobile application, visit the Google Play or Apple store. They can also be
configured via Web and DirectLink DT. The DS4/DS4+ features are built in Bluetooth® 4.0, allowing you to
configure and control your system. The DS3/DS3+ module is not equipped with Bluetooth®, therefore is not
compatible with the DirectLink app for mobile devices.
To configure via DirectLink DT (mobile app):
1. Follow and complete the wiring diagram(s) related to your installation through the app.
2. When installation is complete, select Configure DS4/DS4+.
3. Follow the on-screen instructions.
FLASH REQUIRED!
FLASH REQUIRED!
4 White
4933.CHRYSLER 7.34.195.3 2005 Chrysler 300/300c
©2022 VOXX•DEI LLC. All rights reserved.
Vehicle function compatibilities
This section lists all the functions compatible with this vehicle for the installation illustrated in this guide.
Note: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart.
Parking Lights Control
Heated Seats Activation
Arm Factory Security
Disarm Factory Security
Door Lock Control
Door Unlock
Driver Priority Unlock
Control of aftermarket alarm with OEM remote
* Fuel Level
Immobilizer Bypass-Data No Key Req'd
3x LOCK START (Start control using OEM Remote)
3x LOCK STOP (Stop control using OEM Remote)
Accessory Activation
Ignition Activation
RAP Shut Down (Retained ACC Power)
Remote Start Takeover
SmartStart
Start (Crank) Activation
Tach / RPM Output
Entry Monitoring ALL Door Pins
Entry Monitoring Hood Pin
Entry Monitoring Trunk/Hatch Pin
Brake Status (foot brake)
E-Brake Status
Ignition Status
5933.CHRYSLER 7.34.195.3 2005 Chrysler 300/300c
©2022 VOXX•DEI LLC. All rights reserved.
Pre-installation and application warnings
Firmware notes: This section highlights important information for this specific firmware and will assist in pricing
accordingly, as well as bringing awareness to any operational or vehicle limitations.
T-Harness
compatible
Keys
required for
programming 1Keys required
for operation 0
All connectors are displayed from the wire side (unless specified otherwise).
It is important to check that the fuses are positioned correctly in the module. Proper fuse positioning is displayed on each wiring diagram.
Refer to the "Vehicle connections" following the installation diagram.
General notes: This section highlights important information for this specific firmware.
[1] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin, or if NOT
supported in data.
[2] The siren is ONLY required when enabling the security features during module flashing.
[3] For security-only installations, refer to the "Locating components in the vehicle" section for optional starter disable connection.
6933.CHRYSLER 7.34.195.3 2005 Chrysler 300/300c
©2022 VOXX•DEI LLC. All rights reserved.
Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( ).
(-) Ground: Black: 10
HS CAN Low: Tan: 1
(MUX) Ignition Output: Violet/Brown: 6
HS CAN High: Tan/Black: 2
(+) 12V Input: Red: 6 & 12
(+) 12V Input: Lt. Green/Red: 7
(+) Start Output: Lt. Green: 8
(+) 12V Input: Blue/Red: 2
(+) Ignition Output: Blue: 3
(+) Parking Light Output: White: 5 & 11
CAN B High:
White/Orange,
pin 6
(-) Ground: Black or
Black Striped, pin 4
CAN B Low: White, pin 7
Sentry Key Module
(black 8-pin conn.,
connector side view)
1 8
Refer to the
“Vehicle connections” section
for wire and connector details.
Wiring diagram
(MUX) Ignition:
Violet/Brown, pin 2
(+) Ignition:
Pink/White, pin 3
(+) Start: Pin 4
1
Ignition Switch
(black 5 or 6-pin conn.)
Hood Pin
(-) Hood Input: Gray: 21
Siren
(+) Siren Output: Brown/Red: 11
(-) GWA Output: Red/White: 4
Refer to the Optional starter
disable connection section for
relay and connection details.
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
22 812
4 2442
Slide to open
A module can also be used for
this installation.
IMPORTANT:
Position the
fuses correctly!
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
15
15
7933.CHRYSLER 7.34.195.3 2005 Chrysler 300/300c
©2022 VOXX•DEI LLC. All rights reserved.
Locating components in the vehicle
(-) Ground When Armed (GWA) Output: Red/White: 4
86 85
30
87a
87
Optional starter disable connection
Cut
Starter (conn. side)
Starter (veh. side)
(+) Ignition
Refer to the
Vehicle connections
section for wire and
connector details.
22 812
4 2442
Security Only
Mandatory Connections
Remote Start Only
Legend:
Remote Start + Security
1A diode [1N4002+]
When using an external relay, use a 1N4002 diode or larger.
Important: When flashing your module for Security Only, the Ground When Armed (GWA)
function is pre-configured. When flashing your module for Remote Start & Security, you must
manually assign the designated output to Anti Grind (AG) Starter Kill.
(Applicable to CORE 194+.)
8933.CHRYSLER 7.34.195.3 2005 Chrysler 300/300c
©2022 VOXX•DEI LLC. All rights reserved.
Vehicle connections
The connection information listed below is specific to the 2005 Chrysler 300/300c. Refer to “Pre-installation and application warnings” for a list of important notes.
Data harness, 8-pin white connector (H1)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H1/1 Tan (Data) HS CAN Low Sentry Key Module on ignition switch, black 8 pin plug, pin 7 data white (CAN B BUS) Mandatory
H1/2 Tan/Black (Data) HS CAN High Sentry Key Module on ignition switch, black 8 pin plug, pin 6 data white/orange (CAN B BUS) Mandatory
H1/3 Orange/Brown No Connection No Connection
H1/4 Orange/Green No Connection No Connection
H1/5 Lt. Green No Connection No Connection
H1/6 Violet/Brown (MUX) Ignition Output ignition switch, black 5 pin plug, pin 2 MUX violet/brown Remote Start
Only
H1/7 Orange/Black No Connection No Connection
H1/8 Yellow/Black No Connection No Connection
Analog input/output harness, 22-pin white connector (H2)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H2/1 Lt. Green/Black (-) Factory Alarm Arm Output No Connection
H2/2 Blue/White (-) Ground When Running (Status) Output [6] No Connection
H2/3 Dk. Green/Black (-) Lock Output No Connection
H2/4 Red/White (-) Ground When Armed (GWA) Output [3] Starter:
ignition switch, black 5 pin plug, pin 4
Ignition:
ignition switch, black 5 pin plug, pin 3
Must use a relay.
Must use a 1N4002 diode or larger.
+
+
pink/dk. green
pink/white
Security Only
H2/5 Brown/Black (-) Horn Output horns under hood + dk. green/orange Optional
H2/6 Brown/White (-) AUX 1 Output No Connection
H2/7 White (+) AUX 1 Output No Connection
H2/8 Violet/Black (+) AUX 2 Output No Connection
H2/9 Dk. Blue/Black (-) Unlock Output No Connection
H2/10 Lt. Blue/Black (-) Factory Alarm Disarm Output No Connection
H2/11 Brown/Red (+) Siren Output [2] Security Only
H2/12 Pink (+) Ignition Sense Input No Connection
H2/13 Violet (+) Door Input No Connection
H2/14 Brown (+) Brake Input No Connection
H2/15 White/Blue (-) Activation Input No Connection
H2/16 Red/Blue (-) Headlight Detection Input No Connection
H2/17 Black/White (-) E-Brake Input No Connection
H2/18 Orange/Black (+) Instant Alarm Input No Connection
9933.CHRYSLER 7.34.195.3 2005 Chrysler 300/300c
©2022 VOXX•DEI LLC. All rights reserved.
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H2/19 Blue (-) Trunk Input No Connection
H2/20 Green (-) Door Input No Connection
H2/21 Gray (-) Hood Input [1]
H2/22 Violet/White (AC) Tach Input No Connection
Main harness, 12-pin black connector (H3)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H3/1 Blue/White Relay 1 N.C. - No Connection No Connection
H3/2 Blue/Red Relay 1 N.O. - (+) 12 Volt Input passenger kick, harness to rear + red/white (40A) Remote Start
Only
H3/3 Blue Relay 1 COM - (+) Ignition Output ignition switch, black 5 pin plug, pin 3 + pink/white Remote Start
Only
H3/4 White/Brown Relay 3 N.C. - No Connection No Connection
H3/5 White Relay 3 COM - (+) Parking Light Output passenger kick, harness to rear + white/violet Mandatory
H3/6 Red (+) 12 Volt Input passenger kick, harness to rear + red/white (40A) Mandatory
H3/7 Lt. Green/Red Relay 2 N.O. - (+) 12 Volt Input passenger kick, harness to rear + red/white (40A) Remote Start
Only
H3/8 Lt. Green Relay 2 COM - (+) Starter Output ignition switch, black 5 pin plug, pin 4 + pink/dk. green Remote Start
Only
H3/9 Lt. Green/White Relay 2 N.C. - No Connection No Connection
H3/10 Black (-) Ground Sentry Key Module on ignition switch, black 8 pin plug, pin 4 - black/tan Mandatory
H3/11 White Relay 3 COM - (+) Parking Light Output passenger kick, harness to rear + white/violet Mandatory
H3/12 Red (+) 12 Volt Input passenger kick, harness to rear + red/white (40A) Mandatory
Relay harness, 10-pin white connector (H4)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H4/1 N/A No Connection No Connection
H4/2 Red/Black (+) 12 Volt Input No Connection
H4/3 Pink/Black Flex Relay (pin 87A) No Connection
H4/4 Pink/White (+) Flex Relay Output No Connection
H4/5 Red (+) 12 Volt Input No Connection
H4/6 Green Starter Input (conn. side) No Connection
H4/7 Violet (+) Starter Output (vehicle side) No Connection
H4/8 Orange (+) Accessory Output No Connection
H4/9 Red/White (+) 12 Volt Input No Connection
H4/10 Pink (+) Ignition Input/Output No Connection
10 933.CHRYSLER 7.34.195.3 2005 Chrysler 300/300c
©2022 VOXX•DEI LLC. All rights reserved.
RF Port harness, 2-pin white connector (H5)
Module
Conn./Pin Color Description
H5/1 N/A RF Loop
H5/2 N/A RF Loop
D2D harness, 4-pin white (1) and black (2) connectors (H6)
Module
Conn./Pin Color Description
H6/1 Blue (Data) TX
H6/2 Black (-) Ground
H6/3 Green (Data) RX
H6/4 Red (+) 12 Volt
Temperature sensor harness, 2-pin black connector (H7)
Module Connects To
Conn./Pin Color Description Wire Location (+/-) Wire Color Connection
H7/1 Black Temperature Sensor
H7/2 Black Temperature Sensor
Otros manuales para DS3
1
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Otros manuales de Accesorios para automóviles de Directechs
Directechs
Directechs DB3 Manual de usuario
Directechs
Directechs Directed 403.HYUNDAI10 v2.11 Manual de usuario
Directechs
Directechs NISS06 Manual de usuario
Directechs
Directechs FORD12 Manual de usuario
Directechs
Directechs Directed 933.GM11 v1.21.198.12 Manual de usuario
Directechs
Directechs DB3 Manual de usuario
Directechs
Directechs DIRECTWIRE 403.NISS08 Manual de usuario
Directechs
Directechs DB3 Manual de usuario
Directechs
Directechs DB3 Manual de usuario
Directechs
Directechs FORD13 Manual de usuario
Directechs
Directechs DB3 Manual de usuario
Directechs
Directechs DB3 Manual de usuario
Directechs
Directechs DB3 Manual de instrucciones
Directechs
Directechs DB3 Manual de usuario
Directechs
Directechs DS3+ Manual de usuario
Directechs
Directechs DB3 Manual
Directechs
Directechs DS3+ Manual de usuario
Directechs
Directechs DB3 Manual de usuario
Directechs
Directechs DS3 Manual de usuario
Directechs
Directechs DIRECTED DB3 403.FORD18 Manual
