Digitus U1233 Manual de usuario
1/ 15
802.11ac Wireless USB Adapter
U1233, WU1200
User Manual
Company: HAOLIYUAN (SHENZHEN) ELECTRONIC CO., LTD
Name / Position: Albee shen / PM Tel:+1-626-271-1588ext.818861350
Fax:+1-626-271-1588ext.818861350 Email:A[email protected] Address:17708
Rowland Street. City of Industry, CA 91748 United States
2/ 15
Chapter 1. Introduction
Thank you for purchasing the wireless 802.11b/g/n/a/ac USB
adapter! This adapter is mini size design and you are able to plug it
into the USB port. Excepting common wireless standards
802.11b/g/n, this wireless adapter is also 802.11ac compatible -
data transfer rate is 300/867Mbps.
1.1 Product Features
◆Complies with IEEE 802.11ac , IEEE 802.11a,IEEE 802.11n, IEEE
802.11g and IEEE 802.11b standards
◆Provides USB2.0 connector
◆Provides 300/867Mbps receiving rate and 300/867Mbps sending
rate
◆Supports 20MHz/40MHz/80MHz frequency width
◆Auto-detects and changes the network transmission rate
◆Provides two work modes: Infrastructure and Ad-Hoc
◆Supports 64/128-bit WEP, WPA, WPA2 encryption methods and
802.1x security authentication standard
◆Supports WPS (Wi-Fi Protected Setup) encryption method to free
you from remembering long passwords
◆Easy-to-install, plug and play
◆Supports Windows VISTA/Win7/
Win8/Win8.1/Win10/Linux/Macintosh
1.2 Package contents
The following contents should be found in your box:
◆One Wireless 802.11b/g/n/a/ac USB adapter
◆One CD (include driver/utility/user manual)
Note: If any of the listed contents are damaged or missing, please
contact the retailer from whom you purchased the product for
assistance.
3/ 15
CHAPTER 2: Quick Installation Guide
2.1 Driver Installation
Please follow the following instructions to install your new
wireless USB Adapter:
2.1.1
Insert the USB wireless network card into an empty USB 2.0 port
of your computer when computer is switched on. Never use force
to insert the card, if you feel it‟s stuck, flip the card over and try
again.
2.1.2
The following message will appear on your computer, click
„Cancel / Close‟.
Under Windows Vista and Windows 7
2.1.3
Insert the driver CD into your CD-ROM. You can see autorun
screen below. if not, you can double click „autorun.exe‟ on CD.
4/ 15
Click „Install Driver‟ to start the installation procedure
2.1.4
Once the installation is finished the computer will be asked to
reboot. you can click „Finish‟ and reboot the computer to finish the
installation of driver files.
2.1.5
A new icon will appear near the clock of system tray:
5/ 15
Left-click the icon will launch wireless network configuration
utility, and you can right-click the icon to show the quick menu of
configuration utility. This icon also uses different color to show the
status of wireless connection:
Wireless connection is established, good signal reception.
Wireless connection is established, weak signal reception.
Connection is not established yet.
Wireless network card is not detected.
For detailed instructions of wireless network configuration utility,
please see next chapter.
2.2 Connect to Wireless Access Point
To use wireless network, you have to connect to a wireless
access point first. You can either use Client utility (comes with
network card driver), or Windows Zero Config utility (comes with
Windows operating system).
2.2.1 Using Client Utility
Please follow the following instructions to use Client
configuration utility to connect to wireless access point.
1. Left-click the Client configuration utility icon located at
lower-right corner of computer desktop, and configuration menu
will appear:
HERE!
2. Wireless utility will appear. Click „Available Network‟ menu to
search for wireless access points nearby.
6/ 15
3. Please wait for a while, and all wireless access points which can
be reached by this wireless network card will be displayed here.
7/ 15
If the wireless access point you wish to connect does not appear
here, you can click „Refresh‟ button to scan for wireless access
points again; if the wireless access point you‟re looking for still not
appear, try to move the computer closer.
When the access point you‟re looking for is on the list, left-click it
and then double click it or click „Add to Profile‟.
4. If a password (Network Key) is required to access the wireless
access point, please input it in „Network key‟ (and input it again in
„Confirm network key‟ for confirmation). Click „OK‟ when
password is properly inputted.
8/ 15
5. Network card will attempt to connect to access point now, this
may require few seconds to minutes, please be patient. When the
„Status‟ become „Associated‟, your computer is connected to
access point you selected. Click „Close‟ to close configuration
menu.
9/ 15
NOTE: If you connected to an access point but the connection has
been dropped soon, please check security settings and re-check
password spelling.
2.2.2 Using WPS Connect
Wi-Fi Protected Setup (WPS) is the latest wireless network
technology which makes wireless network setup become very
simple. If you have WPS-enabled wireless access point, and you
want to establish a secure connection to it, you don‟t have to
configure the wireless access point and setup data encryption by
yourself. All you have to do is to go to the WPS setup page of this
wireless card, click a button, and then press a specific button or
enter a set of 8-digit code on the wireless access point you wish to
establish a secure connection - just three simple steps!
For older wireless access points, it‟s possible to perform a
firmware upgrade to become a WPS-enabled access point. Since
they may not have a hardware button to press for WPS setup, you
can use an alternative WPS setup method - input the pin code.
Every WPS-compatible wireless network card support pin code
configuration method; you can just input the code to wireless
access point, and the wireless access point and wireless network
card will do the rest for you.
This wireless network card is compatible with WPS. To use this
function, the wireless access point you wish to connect to must
support WPS function too. Now, please follow the following
instructions to establish secure connection between WPS-enabled
wireless access point and your wireless network card.
This wireless network card supports 2 kinds of WPS: PIN code
and Push-Button.
Please follow the following instructions to setup WPS:
1. Right-click Client configuration utility icon, and click „Open
Config Utility‟.
10 / 15
2. Click „Wi-Fi Protect Setup‟ menu.
3. You can use PIN code or Push-Button configuration, and
WPS-compatible wireless access point must use the same type of
WPS. For instructions on setup each type of WPS, see next 2
chapters for detailed instructions.
PIN Code
To use PIN Code, please click „Pin Input Config (PIN)‟ button:
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Adaptador de Digitus
Digitus
Digitus DA-70300 Manual de usuario
Digitus
Digitus DN-3028 Manual de usuario
Digitus
Digitus DN-70560 Manual de usuario
Digitus
Digitus DA-70838 Manual de usuario
Digitus
Digitus eSATA CARDBUS ADAPTER Manual de usuario
Digitus
Digitus DA-70830 Manual de usuario
Digitus
Digitus DN-7053-1 Manual de usuario
Digitus
Digitus USB 2.0 Manual de usuario
Digitus
Digitus DA-70250-1 Manual de usuario
Digitus
Digitus DA-70841 Manual de usuario
Digitus
Digitus DA-70857 Manual de usuario
Digitus
Digitus DA-10060 Manual de usuario
Digitus
Digitus DN-10180 Manual de usuario
Digitus
Digitus DA-70878 Manual de usuario
Digitus
Digitus DN-70566 Manual de usuario
Digitus
Digitus DA-70156 Manual de usuario
Digitus
Digitus DS-45331 Manual de usuario
Digitus
Digitus WIRELESS 300N AUTO INSTALLATION USB ADAPTER Manual de usuario
Digitus
Digitus DN-10050-1 Manual de usuario
Digitus
Digitus DA-70148-4 Manual de usuario
