DigitaLinx DL-1H1V1U-WP-W Manual de usuario

11675 Ridgeline Drive

Colorado Springs, CO

80918

Rev 180227 Phone: 719-260-0061

Toll-Free: 800-530-8998

Fax: 719-260-0075

DL-1H1V1U-WP-W Owners

Manual

DL-1H1V1U-WP-W Owners Manual

Important Safety Instrucons

»Please completely read and verify you understand all instrucons in this manual before operang this equipment.

»Keep these instrucons in a safe, accessible place for future reference.

»Heed all warnings.

»Follow all instrucons.

»Do not use this apparatus near water.

»Clean only with a dry cloth.

»Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers)

that produce heat.

»Use only accessories specied or recommended by Intelix.

»Explanaon of graphical symbols:

◊ Lightning bolt/ash symbol: the lightning bolt/ash and arrowhead within an equilateral triangle

symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the

product enclosure which may be of sucient magnitude to constute a risk of shock to a person or

persons.

◊ Exclamaon point symbol: the exclamaon point within an equilateral triangle symbol is intended

to alert the user to the presence of important operang and maintenance (servicing) instrucons

in the literature accompanying the product.

»WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR

MOISTURE AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THIS APPARATUS.

»Use the mains plug to disconnect the apparatus from the mains.

»THE MAINS PLUG OF THE POWER CORD MUST REMAIN READILY ACCESSIBLE.

»Do not defeat the safety purpose polarized or grounding-type plug. A polarized plug has two blades with one wider

than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong

is provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of

your obsolete outlet. Cauon! To reduce the risk of electrical shock, grounding of the center pin of this plug must be

maintained.

»Protect the power cord from being walked on or pinched parcularly at the plugs, convenience receptacles, and the

point where they exit from the apparatus.

»Do not block the air venlaon openings. Only mount the equipment per Intelix’s instrucons.

»Use only with the cart, stand, table, or rack specied by Intelix or sold with the equipment. When/if a

cart is used, use cauon when moving the cart/equipment combinaon to avoid injury from p-over.

»Unplug this apparatus during lightning storms or when unused for long periods of me.

»Cauon! Shock Hazard. Do not open the unit.

»Refer to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as

power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate normally, or has been dropped.

DL-1H1V1U-WP-W Owners Manual

Table of Contents

Product Overview�� 5

Package Contents �� 5

Front and Rear Panel �� 6

Transmier View �� 6

Transmier View (connued) �� 7

Installaon Instrucons�� 8

Quick Start �� 8

Connect HDBaseT Link ��8

HDBaseT Connecon ..............................................................................................................................8

Connecng A/V Sources ��9

HDMI Input ............................................................................................................................................. 9

VGA Video Input ..................................................................................................................................... 9

Connecng USB Peripherals �� 9

USB Host ................................................................................................................................................. 9

USB Client (Receiver) .............................................................................................................................. 9

Connecng a Display (Receiver) �� 9

HDMI Output .......................................................................................................................................... 9

Connecng Audio ��10

Audio Input ...........................................................................................................................................10

Audio Output (Receiver) .......................................................................................................................10

Connecng Control (Receiver) ��10

RS232 Control Wiring ...........................................................................................................................10

Apply Power ��10

Applicaon Diagram �� 11

RS232 / CEC Control Conguraon�� 12

CEC Setup and Control ��13

RS232 Control and Conguraon ��14

USB Mode Conguraon ��16

System / Factory Default ��17

Technical Specicaons �� 18

DL-1H1V1U-WP-W Owners Manual

The DigitaLinx DL-1H1V1U-WP-W is a 2x1 auto switching HDBaseT 2.0 transmier that supports the long distance

transport of HDMI, VGA and High Speed USB 2.0 signals up to 100 meters / 330’ using category cabling. The DL-

1H1V1U-WP-W is 4K compable with a max resoluon of 4K@60Hz / 4:2:0 8bit deep color. An addional analog

audio pass through input is located on the wall plate that allows for audio distribuon to the HDBaseT receiver

side. With 48V integrated PoH, the DL-1H1V1U-WP-W can be powered via HDBaseT receiver with a PSE module

or the wall plate can be powered by a local power supply.

The DL-1H1V1U-WP-W gives you the ability to automate the display power ON by using pre-loaded RS232

commands whenever a video signal is introduced to the system using either the HDMI or VGA input. It will also

turn the display power OFF aer a specied amount of me has passed when no video signal is present. It also

gives you the ability to turn the display ON or OFF as well and switch from one input to another manually from

the transmier face plate.

The DL-1H1V1U-WP-W is ideal for situaons where USB must be extended alongside HDMI or VGA for display

interacvity for items such as interacve whiteboards or projectors.

For a complete list of programming commands to automate display power status, please see the complete

owners manual online at www.libav.com or by using the QR code on the print page of this guide.

NOTE: The DL-1H1V1U-WP-W HDBaseT transmier must be used with the DL-HD2-RX HDBaseT 2.0 receiver

(sold separately) to complete the circuit.

Product Overview

Package Contents

• DL-1H1V1U-WP-W HDBaseT Wall Plate Transmier

• (1) Quick Install Guide

• (1) 2 pin Phoenix Male Connector

• (1) 2 gang Decora wall plate cover

• (1) 2m / 6’ USB A to A Cable

DL-1H1V1U-WP-W Owners Manual

Front and Rear Panel

Transmier View

1. VGA Input

2. VGA Audio Input

3. Pass-through Audio Input

4. HDMI Input

5. HDMI LED

•When ON; HDMI signal is being transmied

•When OFF; No HDMI signal is being transmied or signal is unstable

6. VGA LED

•When ON; VGA signal is being transmied

•When OFF; No VGA signal is being transmied or signal is unstable

7. HDCP LED

•When ON; HDCP video is being transmied

•When BLINKING; Non-HDCP video is being transmied

•WHEN OFF; No video is being transmied

8. LINK LED

•When ON; HDBaseT Link is normal

•When OFF / BLINKING; No HDBaseT link or link error

9. POWER LED

•When ON; The transmier is powered on

•When OFF; The transmier is powered o

DL-1H1V1U-WP-W Owners Manual

Transmier View (connued)

10. Input Selecon Buon

11. Display On/O Buon

•Display ON; Short press to power on display immediately

•Display OFF; Press and hold for 3 seconds to power display o

12. USB A Input

13. Service Port for Firmware Update

14. HDBaseT Output

15. DC12V Power Supply Input

DL-1H1V1U-WP-W Owners Manual

Installaon Instrucons

Quick Start

1. Connect HDBaseT Link

2. Connect A/V sources

3. Connect USB peripherals

4. Connect display

5. Connect audio (oponal)

6. Connect and congure control (oponal)

7. Apply power

Connect HDBaseT Link

TIA/EIA-568B

Orange/White

Orange

Green/White

Blue

Blue/White

Green

Brown/White

Brown

Pin 1

Pin 2

Pin 3

Pin 4

Pin 5

Pin 6

Pin 7

Pin 8

1 8

Connect a category cable from the DL-1H1V1U-WP-W HDBaseT output to the DL-HD2-RX receivers HDBaseT

input.

HDBaseT Connecon

Twisted Pair Wiring

Use TIA/EIA-568B wiring for Category 6

connecon between the transmier and

receiver

To ensure proper performance of the DL-1H1V1U-WP-W it is recommended that you use solid

core shielded Category 6 F/UTP cabling at a minimum. Category 5e F/UTP may perform well

but may not support power over HDBaseT reliably.

For opmized performance use the following Liberty Wire and Cable branded cabling;

Category 6 plenum; 24-4P-P-L6SH

Category 6A plenum; 24-4P-P-L6ASH

Category 6 NON-plenum; 24-4P-L6SH

Category 6A NON -plenum; 24-4P-L6ASH

When using shielded category cabling ALWAYS...

....use shielded connectors

....properly ground the category cable

DL-1H1V1U-WP-W Owners Manual

VGA Video Input

USB Host

USB Client (Receiver)

Connect a VGA source device to the VGA input using a VGA cables that are less than or equal to 5 meters in

length. For source devices that are further away, a VGA extension device will be required to complete the

connecon.

Connect a USB host device to the USB A input using a USB A to A cable that is less than or equal to 5 meters in

length.

Connect a USB client device to any USB A port on the DL-HD2-RX receiver using a USB A to A cable that is less

than or equal to 5 meters in length.

Connect an HDMI source device to the HDMI input using HDMI cables that are less than or equal to 5 meters

in length. For source devices that are further away, an extension device will be required to complete the

connecon.

Connecng A/V Sources

Connecng USB Peripherals

HDMI Input

Connecng a Display (Receiver)

HDMI Output

Connect the display devices to HDMI output on the receiver using an HDMI cable that is less than or equal to

5 meters in length. For display devices that are further away, it is highly recommended to ulize the HDBaseT

output.

DL-1H1V1U-WP-W Owners Manual

Connecng Control (Receiver)

RS232 Control Wiring

Audio Input

Audio Output (Receiver)

Connect the DL-HD2-RX receivers RS232 port to a displays serial connecon for serial control.

Apply Power

Plug the power supply into the power input port on the rear of DL-HD2-RX receiver. The receiver will power the

transmier via HDBaseT. Twist the locking ring clockwise to prevent accidental disconnecon of power.

Note: The DL-HD2-RX RS232 port can be congured to send stored serial commands from the

DL-1H1V1U-WP-W

For direcons on RS232 conguraon see complete list of control commands on pg13 RS232 / CEC

Control Conguraon

Note: The DL-HD2-RX audio output only passes audio fed from the dedicated AUDIO IN port on the

DL-1H1V1U-WP-W transmier wall plate, it does not pass embedded HDMI audio

Tx RXD

GND

Rx TXD

DL-SE3H1V-C

Controller or

Device

Connect the display devices RX RS232 signal to TX port of the DL-HD2-RX receiver. Then connect the displays TX RS232

signal to the RX port on the DL-HD2-RX receiver.

Connecng Audio

Connect an audio source to the transmiers audio input using a 3.5mm audio cable. The DL-1H1V1U-WP-W

supports a 3.5mm stereo unbalanced input

Connect an audio amplier to the receivers audio output using a 3.5mm audio cable. The DL-HD2-RX

supports a 3.5mm stereo unbalanced output

Tabla de contenidos

Otros manuales de Transmisor de DigitaLinx

DigitaLinx

DigitaLinx DL-2H1V1U-WP-W Manual de usuario

DigitaLinx

DigitaLinx DL-HDE100 Manual de usuario

DigitaLinx

DigitaLinx DL-3H1U-WP-W Manual de usuario

DigitaLinx

DigitaLinx DL-HD70LS Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario