DigitaLinx DL-SE3H1V-C Manual de usuario

11675 Ridgeline Drive
Colorado Springs, CO
80918
Rev 180115 Phone: 719-260-0061
Toll-Free: 800-530-8998
Fax: 719-260-0075
DL-SE3H1V-C Owners Manual

DL-SE3HV-C Owners Manual
2

DL-SE3H1V-C Owners Manual
3
Important Safety Instrucons
»Please completely read and verify you understand all instrucons in this manual before operang this equipment.
»Keep these instrucons in a safe, accessible place for future reference.
»Heed all warnings.
»Follow all instrucons.
»Do not use this apparatus near water.
»Clean only with a dry cloth.
»Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers)
that produce heat.
»Use only accessories specied or recommended by Intelix.
»Explanaon of graphical symbols:
◊ Lightning bolt/ash symbol: the lightning bolt/ash and arrowhead within an equilateral triangle
symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the
product enclosure which may be of sucient magnitude to constute a risk of shock to a person or
persons.
◊ Exclamaon point symbol: the exclamaon point within an equilateral triangle symbol is intended
to alert the user to the presence of important operang and maintenance (servicing) instrucons
in the literature accompanying the product.
»WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THIS APPARATUS.
»Use the mains plug to disconnect the apparatus from the mains.
»THE MAINS PLUG OF THE POWER CORD MUST REMAIN READILY ACCESSIBLE.
»Do not defeat the safety purpose polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong
is provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of
your obsolete outlet. Cauon! To reduce the risk of electrical shock, grounding of the center pin of this plug must be
maintained.
»Protect the power cord from being walked on or pinched parcularly at the plugs, convenience receptacles, and the
point where they exit from the apparatus.
»Do not block the air venlaon openings. Only mount the equipment per Intelix’s instrucons.
»Use only with the cart, stand, table, or rack specied by Intelix or sold with the equipment. When/if a
cart is used, use cauon when moving the cart/equipment combinaon to avoid injury from p-over.
»Unplug this apparatus during lightning storms or when unused for long periods of me.
»Cauon! Shock Hazard. Do not open the unit.
»Refer to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.

DL-SE3HV-C Owners Manual
4
Table of Contents
Product Overview��������������������������������������������������������������������������������������������������������������������������������������� 5
Package Contents ��������������������������������������������������������������������������������������������������������������������������������������� 5
Front and Rear Panels��������������������������������������������������������������������������������������������������������������������������������� 6
Transmier���������������������������������������������������������������������������������������������������������������������������������������������������� 6
Receiver��������������������������������������������������������������������������������������������������������������������������������������������������������� 7
Installaon Instrucons������������������������������������������������������������������������������������������������������������������������������ 8
Quick Start ���������������������������������������������������������������������������������������������������������������������������������������������������� 8
Mount the Switcher / Extender �������������������������������������������������������������������������������������������������������������������� 8
Connecng Sources��������������������������������������������������������������������������������������������������������������������������������������� 8
HDMI Input ............................................................................................................................................. 8
VGA Video Input ..................................................................................................................................... 8
Connecng a Display������������������������������������������������������������������������������������������������������������������������������������� 9
HDMI Output .......................................................................................................................................... 9
HDBaseT Output ..................................................................................................................................... 9
Connect Audio Output����������������������������������������������������������������������������������������������������������������������������������� 9
Connecng Control �������������������������������������������������������������������������������������������������������������������������������������10
RS232 Control Wiring ...........................................................................................................................10
Relay Port Wiring ..................................................................................................................................10
Apply Power ������������������������������������������������������������������������������������������������������������������������������������������������ 10
Applicaon Diagram �������������������������������������������������������������������������������������������������������������������������������� 11
RS232 and TCP/IP Control ������������������������������������������������������������������������������������������������������������������������� 12
Video Input Switching, Conguraon ���������������������������������������������������������������������������������������������������������12
Video Output Conguraon������������������������������������������������������������������������������������������������������������������������ 13
EDID Conguraon �������������������������������������������������������������������������������������������������������������������������������������13
Video Input HDCP Compliance ��������������������������������������������������������������������������������������������������������������������14
CEC Setup and Control �������������������������������������������������������������������������������������������������������������������������������� 15
RS232 Port Control / Conguraon������������������������������������������������������������������������������������������������������������16
Relay Port Control / Conguraon��������������������������������������������������������������������������������������������������������������19
IP Address Conguraon�����������������������������������������������������������������������������������������������������������������������������20
Transmier / Receiver Key Lock ������������������������������������������������������������������������������������������������������������������20
System Power / Factory Default������������������������������������������������������������������������������������������������������������������ 21
Technical Specicaons ���������������������������������������������������������������������������������������������������������������������������� 22

DL-SE3H1V-C Owners Manual
5
The Digitalinx DL-SE3H1V-C is a 4K compable, 4 input mul format A/V auto switcher, extender and video scaler
system that supports long distance transport of HDMI between transmier and receiver up to 70 meters / 230’
using Cat6 cabling.
The DL-SE3H1V-C features a total of 3 video inputs on the transmier; (2) HDMI, (1) VGA with 3.5 Audio and
(1) HDMI input located on the receiver for integraon of a local HDMI input such as a wireless BYOD / screen
share product. The receiver also features a stereo analog audio output to connect to an audio amplier for audio
reinforcement, an RS232 serial control port for display control / connecvity and two relay ports for projecon
screen or window shade control / connecvity.
The DL-SE3H1V-C can be controlled via push buon control on the transmier and receiver or by issuing telnet
and serial commands when integrated with a 3rd party control system. The system can be programmed to
automate RS232, CEC and relay control when a new video signal is introduced to the system thus creang a
stand alone, plug and play A/V automaon system that consolidates control of a connected display and room
peripherals such as a projector screen or window shade.
Product Overview
Package Contents
• DL-SE3H1V-C Transmier and Receiver Set
• Quick Install Guide
• DC12V 3A power supply with US, UK, EU and AU adapter rings
• (4) 3.5mm 3 pin phoenix male connectors
• (4) Mounng Brackets

DL-SE3HV-C Owners Manual
6
Front and Rear Panels
Transmier
1 2 3 4 5 6 7 98
1. VGA IN - VGA video input
2. FW UPDATE - USB port for transmier rmware updates
3. AUDIO IN - 3.5mm analog audio input to accompany VGA input
4. HDMI IN1 - HDMI video input #1
5. STATUS LEDS
• POWER- When solid, the transmier is receiving power
• STATUS- When solid, the transmier is working properly
• HDCP - When solid, HDCP content is being transmied, when blinking NON HDCP content is being transmied
• LINK - When solid, the link between transmier and receiver is normal. When blinking or o the link between
transmier and receiver is not operable
6. HDMI IN2 - HDMI video input #2
7. HDBT OUT - HDBaseT output to connect to HDBaseT input on receiver via category cable
8. FRONT PANEL CONTROLS
• AUTO - Enables auto switcher. When LED is on the auto switch funcon is ON
• VGA IN - VGA video input selector
• HDMI IN1 - HDMI IN1 input selector
• HDMI IN2 - HDMI IN2 input selector
LED indicator status for VGA and HDMI inputs:
• When LED is violet, the input has signal and is selected
• When LED is orange, the input has signal but is not selected
• When LED is blue, the input has no signal but is selected
• When LED is o, the input has no signal and is not selected
9. DC12V - Locking power port to connect DC12V power adapter

DL-SE3H1V-C Owners Manual
7
Receiver
1 3
2
4 5 8
67 9 10 11 12
1. LAN - RJ45 Telnet control port
2. FW UPDATE - USB port for receiver rmware updates
3. HDBT IN - HDBaseT input to connect to HDBaseT output on transmier via category cable
4. STATUS LEDS
• POWER- When solid, the transmier is receiving power
• SCALER - When solid, the scaler module is working properly
• STATUS- When solid, the transmier is working properly
• HDCP - When solid, HDCP content is being transmied, when blinking NON HDCP content is being transmied
• LINK - When solid, the link between transmier and receiver is normal. When blinking or o the link between
transmier and receiver is lost and should be reset
5. HDMI IN - HDMI receiver input for local HDMI source
6. HDMI OUT - HDMI output for display connecvity
7. AUDIO OUT - Stereo analog audio output
8. FRONT PANEL CONTROL
• AUTO - Enables auto switcher. When LED is on the auto switch funcon is ON
• HDBT IN - HDBaseT / Transmier input selector
• HDMI IN - Receiver HDMI input selector
LED indicator status for HDBT and HDMI input:
• When LED is violet, the input has signal and is selected
• When LED is orange, the input has signal but is not selected
• When LED is blue, the input has no signal but is selected
• When LED is o, the input has no signal and is not selected
9. RS232 - Serial control port for display control / 3rd party control
10. RELAY 1 / RELAY 2 - Relay port 1 and 2 for room peripheral control
11. SCALER UPDATE - USB port for scaler rmware updates
12. DC12V - DC12V - Locking power port to connect DC12V power adapter

DL-SE3H1V-C Owners Manual
8
Installaon Instrucons
Quick Start
Mount the Switcher / Extender
1. Mount the switcher / extender set
2. Connect sources
3. Connect display
4. Connect audio output (oponal)
5. Connect control (oponal)
6. Apply power
At least 2 inches of free air space is required on both sides of the DL-SE3H1V-C for proper side venlaon.
Avoid mounng the DL-SE3HV1-C near a power amplier or any other source of signicant heat.
Aach the supplied mounng rails to the sides of the receiver. Once the rails are installed the receiver can be
mounted in an A/V enclosure or on the wall behind a display or above a projector.
Aach the supplied mounng rails to the sides of the transmier. Once the rails are installed, the scaler is
ready to be mounted under a table.
VGA Video Input
Connect a VGA source device to the VGA input using a VGA cables that are less than or equal to 5 meters in
length. For source devices that are further away, a VGA extension device will be required to complete the
connecon.
Connect HDMI source devices to the HDMI inputs using HDMI cables that are less than or equal to 5 meters
in length. For source devices that are further away, an extension device will be required to complete the
connecon.
Connecng Sources
HDMI Input

DL-SE3H1V-C Owners Manual
9
L
R
L
R
AUDIO
SOURCE DL-SE3H1V-C
Connecng a Display
HDMI Output
Connect the display devices to HDMI output on the receiver using an HDMI cable that is less than or equal to
5 meters in length. For display devices that are further away, it is highly recommended to ulize the HDBaseT
output.
TIA/EIA-568B
Orange/White
Orange
Green/White
Blue
Blue/White
Green
Brown/White
Brown
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
1 8
Connect a category cable to the transmier and the HDBaseT receiver.
HDBaseT Output
Connect Audio Output
Insert the removable 3-pin phoenix connector block to the audio output. The DL-SE341V-C supports a stereo
unbalanced output
Twisted Pair Wiring
Use TIA/EIA-568B wiring for Category 6
connecon between the transmier and
receiver
To ensure proper performance of the DL-SE3H1V-C, it is recommended that you use solid core
shielded Category 6 F/UTP cabling at a minimum. Category 5e F/UTP may perform well but
may not support power over HDBaseT reliably.
For opmized performance use the following Liberty Wire and Cable branded cabling;
Category 6 plenum; 24-4P-P-L6SH
Category 6A plenum; 24-4P-P-L6ASH
Category 6 NON-plenum; 24-4P-L6SH
Category 6A NON -plenum; 24-4P-L6ASH
When using shielded category cabling ALWAYS...
....use shielded connectors
....properly ground the category cable

DL-SE3H1V-C Owners Manual
10
Connecng Control
RS232 Control Wiring
Connect the DL-SE3H1V-C receivers LAN port to an Ethernet control network for telnet control.
Connect the DL-SE3H1V-C RS232 port on the receiver for serial control.
Relay Port Wiring
Apply Power
Plug the power supply into the power input port on the rear of DL-SEH1V-C receiver The receiver will power
the transmier via HDBaseT. Twist the locking ring clockwise to prevent accidental disconnecon of power.
Note: The DL-SE3H1V-C RS232 port can either be used with a control system for serial
control of the DL-SE3H1V-C transmier and receiver or can be connected to an external
display for ON/OFF display control using telnet control.
For complete list of control commands see pg13 RS232 and TCP/IP Control
Tx RXD
GND
Rx TXD
DL-SE3H1V-C
RX
Controller or
Device
Connect the controller or device RX signal to TX port of the DL-SE3H1V-C receiver. Then connect the controller or device
TX signal to the RX port on the DL-SE3H1V-C receiver.
For the normally open contacts (NC), connect a circuit between
the NO and COM terminals of the 3-pin
For the normally closed contacts (NC), connect a circuit be-
tween the NC and COM terminals of the 3-pin phoenix connec-
tor
I/O STATE RELAY STATE
NO NC
ON CLOSED OPEN
OFF OPEN CLOSED
Otros manuales para DL-SE3H1V-C
1
Tabla de contenidos
Otros manuales de Cambiar de DigitaLinx

DigitaLinx
DigitaLinx DL-S41-H2 Manual de usuario

DigitaLinx
DigitaLinx DL-AS31-1H1DP1V Manual de usuario

DigitaLinx
DigitaLinx DL-SE3H1V-C Manual de usuario

DigitaLinx
DigitaLinx DL-S41 Manual de usuario

DigitaLinx
DigitaLinx DL-AS31-2H1V Manual de usuario

DigitaLinx
DigitaLinx DL-S41-H2 Manual de usuario

DigitaLinx
DigitaLinx IP 2000 Series Manual de usuario

DigitaLinx
DigitaLinx DL-AS21C Manual de usuario

DigitaLinx
DigitaLinx DL-SC41U-TX Manual de usuario

DigitaLinx
DigitaLinx DL-HDM88A-H2 Instrucciones de montaje























