DigitaLinx DL-RMKTC2H-2 Manual de usuario

DL-RMKTC2H-W Installaon Guide

The Digitalinx DL-RMKTC2H-W is a mul-funcon AV distribuon system designed to provide

HDMI video switching, system control, video extension and analog audio amplicaon in

a convenient kit. Ulizing the Valens Colligo VS2110 series chips, power, control, video up

to 1080p, and audio are transported over a single 30m (98 ) solid core Category 5e cable

between the wall plate transmier and the receiver. The wall plate control module connects

to the wall plate transmier with a second Category 6 cable. All the power needed for the

system is provided by the receiver. Addionally, the receiver features a built-in web GUI for

control and analog audio de-embedding to a built-in 2x20 wa stereo amplier.

FIRMWARE ON LINK HDCP

DL-RMKTC2H-2

RX / Receiver

OUTPUT CONTROL AUDIO MICINPUTNETWORK

2x20 Watts @ 4Ω24V DC

LINE MIC

MIC

LINE OUT

TX RX

RS232IR OUT REMOTE

MUTE

FROM

TOUCHSCREEN

TO DISPLAYHDBT IN/PoC

TCP/IP

HDMI IN 1SOURCE SELECT

TO PC HDMI IN 2

FIRMWARE

RESET

HDCPLINK

VOLUME

MIC

SOURCE

HDMI 1

HDMI 2

CONFIG

OFF

Included Accessories

Safety Precauons

• DL-RMKTC2H-W Control Keypad, Transmier and Receiver Set

• Locking Power Supply with US Power Cable

• USB Type A to Type B Cable

• IR Emier

• Two Mounng Rails with Screws

• Six Wall Box Screws

• Three 3-pole Removable Terminal Blocks

• One 2-pole Removable Terminal Block

• One 4-pole Removable Terminal Block

• Installaon Guide

To insure the best from the product, please read all instrucons carefully before using the

device. Save this manual for further reference.

• Unpack the equipment carefully and save the original box and packing material for

possible future shipment.

• Follow basic safety precauons to reduce the risk of re, electrical shock and injury to

persons.

• Do not dismantle the housing or modify the module. It may result in electrical shock or

burn.

• Using supplies or parts not meeng the products’ specicaons may cause damage,

deterioraon or malfuncon.

• Refer all servicing to qualied service personnel.

• To prevent re or shock hazard, do not expose the unit to rain, moisture or install this

product near water.

• Do not put any heavy items on the extension cable in case of extrusion.

• Do not remove the housing of the device as opening or removing housing may expose you

to dangerous voltage or other hazards.

• Install the device in a place with good venlaon to avoid damage caused by overheang.

• Keep the module away from liquids.

• Spillage into the housing may result in re, electrical shock, or equipment damage. If an

object or liquid falls or spills on to the housing, unplug the module immediately.

• Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the

device before cleaning.

• Unplug the power cord when le unused for a long period of me.

• Informaon on disposal for scrapped devices: do not burn or mix with general household

waste. Please treat them as normal electrical waste and recycle the devices properly.

Receiver Front Panel

Receiver Rear Panel

FIRMWARE ON LINK HDCP

DL-RMKTC2H-W

RX / Receiver

12 3 4 5

OUTPUT CONTROL AUDIO MICINPUTNETWORK

2x20 Watts @ 4Ω24V DC

LINE MIC

MIC

LINE OUT

TX RX

RS232IR OUT REMOTE

MUTE

FROM

TOUCHSCREEN

TO DISPLAYHDBT IN/PoC

TCP/IP

A B C D E F G H I J K L

1. Firmware Update Port

2. System Power Indicator

3. HDBaseT Link Indicator

4. HDCP Status Indicator

5. Receiver Power Indicator

A. Network Port

B. HDBaseT Input and PoC Output

C. HDMI Output

D. USB Port to Touchscreen Display

E. IR Output to Display

F. RS232 Output to Display

G. Remote Mute Contact Closure

H. Line Level Analog Audio Output

I. Line/Mic Level Selector Switch

J. Microphone Input

K. Speaker Output

L. 24V DC Power Input

Transmier Front

Transmier Rear

HDMI IN 1SOURCE SELECT

TO PC HDMI IN 2

FIRMWARE

RESET

HDCPLINK

1 2 3

4 5 6

PoC IN

HDBT OUT

POWER

RS232

DL-RMKTC2H-W

TX / Transmitter

1. Power Indicator and Source Select Buon

2. Link and HDCP Status LEDs and Reset Buon

3. HDMI Input 1 with Acvity Indicator

4. USB Port to Host PC

5. Firmware Update Port

6. HDMI Input 2 with Acvity Indicator

A. HDBaseT Output and PoC Input

B. Power and RS232 to Control Panel

Control Panel Front

Control Panel Rear

VOLUME

MIC

SOURCE

HDMI 1

HDMI 2

CONFIG

OFF

POWER

RS232

FIRMWARE

DL-RMKTC2H-W

PAD / Control Pad

A B

1. Mic/Source Indicator

2. System/Display On Buon

3. HDMI Input 1 Select Buon

4. IR Receiver

5. Mulfuncon Volume Control with Volume

Level Indicator

6. System/Display O Buon

7. HDMI Input 2 Select Buon

8. Conguraon Port

A. Power and RS232 from Transmier

B. Firmware Update Port

Cabling Requirements

TIA/EIA-568B

Orange/White

Orange

Green/White

Blue

Blue/White

Green

Brown/White

Brown

Pin 1

Pin 2

Pin 3

Pin 4

Pin 5

Pin 6

Pin 7

Pin 8

1 8

Twisted Pair Wiring

Use TIA/EIA-568B wiring for Category 6

connecon between send and receive

units.

RS232 Wiring

Connect the display RX signal to Tx on

the DL-RMKTC2H-W receiver Connect

the display TX signal to Rx on the DL-

RMKTC2H-W extender.

To ensure proper performance of the DL-RMKTC2H-W, it is recommended that you use solid

core Category 6 F/UTP cabling at a minimum between control keypad and transmier and

between transmier and receiver. Category 5e F/UTP may perform well but may not support

power over HDBaseT reliably.

When using shielded category cabling ALWAYS...

....use shielded connectors

....properly ground the category cable

Tx RXD

GND

Rx TXD

DL-RMKTC2H

(RX) Display

Speaker Wiring Conguraons

4Ω Load with 4Ω Speakers

–

4Ω

–

4Ω

4Ω Load with 8Ω Speakers

–

8Ω

–

8Ω

1. Verify all components included with the DL-RMKTC2H-W are present before installaon.

2. Turn o power and disconnect the audio/video equipment by following the manufacturer’s

instrucons.

3. Aach the included rubber feet or mounng ears to the receiver.

4. Connect an HDMI cable between the HDMI output of the Receiver and the HDMI input of

the display. The HDMI cable should not exceed 5 meters (16 feet).

5. Connect a microphone to the microphone input connector.

6. Adjust the microphone input mode selector based on the type of microphone to be

connected to the Receiver.

a. MIC – 48dB gain

b. LINE – 4dB gain

7. Connect the speakers to be used in accordance with the Speaker Wiring Conguraons. If

an external audio amplier is to be used with the system, connect the unbalanced analog

audio output of the Receiver to the input of the amplier.

8. If the display is to be controlled via IR, plug the IR emier to the IR Out port of the Receiver

and mount the IR emier bud to the IR receiver port of the display.

9. If the display is to be controlled via RS232, plug the 3-pole terminal plug end of the

included RS232 cable into the RS232 port on the Receiver and the DE9 end to the display.

10. Connect a USB cable between the displays interacve white board USB port and the USB

port labeled “From Touchscreen” on the rear of the Receiver.

11. Connect a Category 6A or greater cable between the Network TCP/IP port and the

facility’s network.

12. Connect a Category 6A or greater cable between the Input port of the Receiver and the

Output port of the Transmier. This cable cannot exceed 30 meters (98 feet).

13. Connect a Category 6A or greater cable between the Power and RS232 port on the

Transmier and the Power and RS232 port on the Control Panel.

14. Connect the included USB cable between the TO PC port on the front of the Transmier

and the PC to receive the commands from the interacve white board.

15. Plug the power supply into the power input port on the Receiver.

16. Power on the Receiver by plugging the power cable into the power supply.

17. Power on all audio/video devices.

Installaon Instrucons

Web Browser Conguraon

Logging In

The default IP address of the DL-RMKTC2H-W is 192.168.0.178. This can be changed in the

Network sengs.

To change the sengs of the web browser interface or program RS232 commands for the

display, log into the DL-RMKTC2H-W as an administrator. The User Name is admin and the

default Password is admin.

Device Control Screen

HDMI

Switch between HDMI 1 and HDMI 2.

Display

Turn the display on or o.

System

Turn the system on or o.

Volume

Mute and unmute audio sources. Volume may be changed by pressing the “+” or “-“ buons

or by dragging the volume slider.

To enter the conguraon sengs, click on the gear icon on the lower le corner of the

Control interface.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Extensor de DigitaLinx

DigitaLinx

DigitaLinx DL-1H1A1U-WPKT-W Manual de usuario

DigitaLinx

DigitaLinx DL-UHDRC70 Manual de usuario

DigitaLinx

DigitaLinx IPEX2001 Manual de usuario

DigitaLinx

DigitaLinx DL-HD70LSIR Manual de usuario

DigitaLinx

DigitaLinx DL-HD2100 Manual de usuario

DigitaLinx

DigitaLinx DL-HD70LS-TX Manual de usuario

DigitaLinx

DigitaLinx DL-HDE100-H2 Manual de usuario

DigitaLinx

DigitaLinx DL-HD70LSIR Manual de usuario

DigitaLinx

DigitaLinx DL-HDE100 Manual de usuario

DigitaLinx

DigitaLinx DL-HD50C Manual de usuario

DigitaLinx

DigitaLinx DL-HD70 Manual de usuario

DigitaLinx

DigitaLinx DL-HD70LS-H2 Manual de usuario

DigitaLinx

DigitaLinx DL-UHDRC70 Manual de usuario

DigitaLinx

DigitaLinx DL-UHDRC70 Manual de usuario

DigitaLinx

DigitaLinx DL-HD2100 Manual de usuario

DigitaLinx

DigitaLinx DL-HDE100 Manual de usuario

DigitaLinx

DigitaLinx DL-HD70 Manual de usuario

DigitaLinx

DigitaLinx DL-HD70LS Manual de usuario

DigitaLinx

DigitaLinx DL-HD2100 Manual de usuario

DigitaLinx

DigitaLinx DL-HDFO Manual de usuario

DigitaLinx

DigitaLinx DL-FHD2 Manual de usuario

DigitaLinx

DigitaLinx DL-DVI-S Instrucciones de funcionamiento

DigitaLinx

DigitaLinx DL-UHDRC70 Manual de usuario

Manuales populares de Extensor de otras marcas

SY HDBT-60T Manual de usuario

Appsys ProAudio

Appsys ProAudio ADX-16 Manual de usuario

Atlona

Atlona RS232 Manual de usuario

IDK

IDK OPF-TH1000-A Manual de usuario

Enable-IT

Enable-IT 824WP Manual de usuario

Worx

Worx Landroid RadioLink WA0864 Hoja de especificaciones

TP-Link

TP-Link TL-WA730RE Manual de usuario

Camplex

Camplex CMX-HDMI-SFPL Manual de usuario

SC&T

SC&T HE03-4K Manual de usuario

Marmitek

Marmitek MegaView70 Manual de usuario

Samsung

Samsung SCS-26UC4 Manual de usuario

Foxun

Foxun SX-GES24 Manual de usuario

MuxLab

MuxLab 500771 Manual de usuario

foxunhd

foxunhd SX-AEX01 Manual de usuario

TERK Technologies

TERK Technologies LFIRX2 Manual de usuario

Devolo

Devolo Audio Extender Manual

Edimax

Edimax EW-7438RPn V2 Manual de usuario

Shinybow USA

Shinybow USA SB-6335T5 Manual de usuario